• Laser Solutions
• /
• v.11 no.4
• /
• pp.29-34
• /
• 2008

Ultraviolet laser micromachining has increasingly been applied to the electronics industry where precision machining of high-density, multi-layer, and multi material components is in a strong demand. Due to the ever-decreasing size of electronic products such as cellular phones, MP3 players, digital cameras, etc., flexible printed circuit board (FPCB), multi-layered with polymers and metals, tends to be thicker. In present, multi-layered FPCBs are being mechanically cut with a punching die. The mechanical cutting of FPCBs causes such defects as burr on layer edges, cracks in terminals, delamination and chipping of layers. In this study, the laser cutting mechanism of FPCB was examined to solve problems related to surface debris and short-circuiting that can be caused by the photo-thermal effect. The laser cutting of PI and FCCL, which are base materials of FPCB, was carried out using a pico-second laser(355nm, 532nm) and nano-second UV laser with adjusting variables such as the average/peak power, scanning speed, cycles, gas and materials. Points which special attention should be paid are that a fast scanning speed, low repetition rate and high peak power are required for precision machining.

• Journal of the Korean Society for Precision Engineering
• /
• v.26 no.5
• /
• pp.48-56
• /
• 2009

In this paper, laser-assisted machining(LAM) has been employed to machine hot isostatically pressed (HIPed) Si3N4 work pieces. Due to little residual flaws and porosity, HIPed $Si_3N_4$ work pieces are more difficult to machine compared to normally sintered $Si_3N_4$ workpieces. In LAM, the intense energy of laser was used to enhance machinability by locally heating the workpiece and thus reducing yield strength. In experiments, the laser power ranges from 200W to 800W and the diameter of work pieces is 16mm. While machining, the surface temperature was kept nearly constant by laser heating except for a short period of rise time of max. 58 seconds. Results showed as feed rate increases the surface temperature of $Si_3N_4$ workpieces decreases slightly, whereas the effect of depth of cut is disregardable. With a laser power of 800W, achievable maximal depth of cut as 0.7mm and feed rate was 0.03mm/rev.

• IE interfaces
• /
• v.18 no.1
• /
• pp.73-81
• /
• 2005

Injection molding has been widely used in producing plastic parts in large quantities. However, its productivity mainly depends on the expertise and experience of skilled workers because of the difficulty and complexity to determine a robust injection molding condition which is not influenced by the minor operational variation of an injection molding machine and produces good parts continuously. This study analyzes the defect types of the parts and proposes a support system to assist users in determining the robust process condition. The support system calculates the start condition from the information of an injection mold, the injection molding machine, the resin used, and the part. Through the iterative step which updates the condition using the defect information of the part tested, users can obtain the initial condition which produces the part without any problem for the first time. The support system also assists users in obtaining the robust condition from the initial condition using the technique of experimental design. To prove the validity of the support system, this study implements it in the control panel of the injection molding machine.

• Journal of the Korean Society for Precision Engineering
• /
• v.26 no.4
• /
• pp.47-54
• /
• 2009

In the last few years, lasers have found new applications as tools for ceramic machining which is laser-assisted machining(LAM). LAM process for the machining of difficult-to-machine materials such as structural ceramics, has recently been studied on silicon nitride workpiece for a wide range of operating condition. However, there have been few studies on rake angle in LAM process. In this paper we analyzed difference of machinability between positive and negative rake angle in tools. We have obtained interesting results that we could eliminate chattering, lower specific cutting and cutting ratio in case of positive rake angle. The results suggest that positive rake angled tools can make more plastic deformation and stable cutting of silicon nitride in comparison with negative rake angled one.

• Journal of the Korean Society for Precision Engineering
• /
• v.25 no.12
• /
• pp.132-138
• /
• 2008

Recently, mastering processes for high density optical disc such as Blu-ray disc rely on electron beams, which are operable in only vacuum. In the mastering process, one of the most important tasks is to design precision stages for providing precise positioning of the works with respect to the source in a high vacuum environment. In this paper, we have developed a precision rotation table usable in the electron beam mastering. The rotation table adopted air bearings for a high positioning repeatability and velocity stability. The air leakage from the air bearings has been minimized by employing the differential exhaust scheme using three steps of air drain. The design parameters such as diameters of exhaust lines, seal lengths, and pumping speeds were decided according to the optimization method using genetic algorithm. The performance on the vacuum level of the rotation table was evaluated experimentally and theoretically. The results indicate that a vacuum level of $10^{-4}$ Pa is achieved with operation of air bearings in a vacuum chamber, which is sufficient for the electron beam mastering.

• Laser Solutions
• /
• v.12 no.1
• /
• pp.25-33
• /
• 2009

In laser-assisted machining (LAM), laser beam is used to locally increase the temperature of a workpiece and thus to enhance the machinability. In order to set the temperature of the material removal area of a workpiece at an optimal value, process parameters, such as laser power, feed rate, and rotational velocity, have to be carefully controlled. In this work, the effects of laser power and feed rate on the temperature distribution of a silicon nitride rotating at a constant velocity were experimentally investigated. Using a pyrometer, temperatures at various locations of the silicon nitride were measured both in circumferential and axial directions. The measured temperatures were fitted to a quadratic equation to approximate the temperature at the cutting location. The machining results showed that cutting force and tool wear were decreased when the temperature at the cutting location was increased.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.22 no.5
• /
• pp.837-844
• /
• 2013

This study performs erection of a pendulum hanging at a free end of an arm by rotating the arm to the upright position. A mathematical model of a rotary inverted pendulum system (RIPS) is derived. A brain emotional learning based intelligent controller (BELBIC) is designed and used as a controller for swinging up and balancing the pendulum of the RIPS. In simulations performed in the study, a pendulum is initially inclined at $45^{\circ}$ with respect to the upright position. A simulation is also performed for evaluating the adaptiveness of the designed BELBIC in the case of system variation. In addition, a simulation is performed for evaluating the robustness of the designed BELBIC against a disturbance in the control input.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.9 no.2
• /
• pp.15-24
• /
• 2000

An intelligent software system which can support efficiently and systematically machine tool design by utilizing deign knowledge is described in this paper. The process of embodiment design of a machining center was modelled represented by IDEF0 and embedded in the system. A hybrid type inference engine has been introduced so that the system can effec-tively deal with knowledge represented in diversified forms The design system was developed on the basis of object-ori-ented programming and has been coded into one software system which can be ported on Windows NT.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.6 no.2
• /
• pp.83-91
• /
• 1997

Interactive measuring Part Program Generating Tools (IMPPGT) realized on the FANUC 15MA using touch trigger probes and interactive macro functions of the CNC were developed for intelligent measuring and inspection systems on the machine tools. Machine tools. Menu driven measuring and inspection functions of the IMPPGT were studied and implemented on the CNC through the macro executor and ROM writer. In order to automate measurement and inspection procedures in machine shops, measuring G Code system was also proposed. Using the developed measuring G Code system on the machine tool, untended measurement and inspection operation was able to be realized in FMS lines.

• The Journal of Korea Robotics Society
• /
• v.2 no.1
• /
• pp.103-108
• /
• 2007

Intelligent Robot is considered as one of the Next Generation Growth Engine in many countries. The application fields are expected to be widen from 80's robotics for manufacturing to many applications such as military, space, medical, personal, etc. To reduce the R&D investment risk Technical Roadmap is prepared by Japan, Europe and Korea. In this paper, the technical Roadmap of the countries was analysed to get the idea of future of Robotics. Robotics is considered as one of solutions of future aged society. Robot can assist and company with elderly people in the near future. On the other hand, Robot is considered as a core technology of manufacturing competitive power. Industrial competitiveness also would be dependent on robot technology. Special Service robot has many application areas and each country has different target based on the situation. With the comparison of technical roadmap, we have suggested some ideas to improve Korea's roadmap.