• 한국환경과학회지
• /
• 제23권7호
• /
• pp.1339-1347
• /
• 2014

This study were performed on roadside buffer green in Songpa-dong, Songpa-gu, Seoul in order to analyze the anion concentration according to the type of composition of roadside buffer green. Buffer green separating the physical structure of the measurement points and measurement locations were separated by roadside, green interior, the other side of the road. planting density and deposit of trees per each buffer green was measured in the order of mounding type> slope type> the plain type. If the measured temperature of the location-specific weather elements roadside> inside> the other side of the road in order of measurement and the temperature is lowered farther away from the road. If the relative humidity of the road on the other side> inside> the roadside in order to measure and this is the opposite of the temperature tendency. According to physical structure reduction of the temperature on the other side of the road and roadside in order of mounding type> the plain type> slope type was measured. As a result of measuring a anion therefore concentration of the anion inside of melt is in order of mounding type> the plain type> slope type, tended to match the melt characteristics. According to measured positions anion concentration is in the order of the other side of the road> inside> the roadside was measured. As a result of correlation analysis, in the case of measurement location-specific weather and anions the temperature is positive correlation, relative humidity is negative correlation and that's results of previous studies were supported.

• 전기전자학회논문지
• /
• 제19권4호
• /
• pp.590-595
• /
• 2015

본 논문은 타일 기반 레스터라이져에서 연산이 필요하지 않은 하위 계층에 대한 호출을 막아 연산의 효율을 올릴수 있는 계층 구조의 설계를 제안한다. 제안하는 계층 구조는 내외부 판정과 각 하위 계층이 가지는 타일의 최대 좌표값, 최소 좌표값을 이용하여 하위 계층을 3가지 형태로 분류한다. 각 하위 계층이 분류되는 형태에 따라 해당 계층의 연산의 필요 여부를 구분할 수 있으며 연산이 필요하지 않는 하위 계층에 대한 호출을 수행하지 않는 것으로 그래픽 처리과정의 전체 연산량을 줄일 수 있다. 제안하는 구조를 이용하여 하위 계층의 분류를 통해 그래픽 처리의 연산 시간을 줄일 수 있으며 3D 모델을 구성하는 정점의 밀집도가 클수록 높은 효율을 보인다.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2003년도 추계학술대회
• /
• pp.254-258
• /
• 2003

Electronic Speckle Pattern for quantitative evaluation of a impact defect inside of composite material plate are described. The impact on composite material makes inside delamination which is difficult to detect visual inspection and ultrasonic testing due to non-homeogenous structure. This paper proposes the quantitative evaluation technique of defects under real impact. Artificial defects are designed inside of composite plate for development of inspection technique and real defects under impact are inspected and compared with results of visual inspection.

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 2003년도 유체기계 연구개발 발표회 논문집
• /
• pp.251-256
• /
• 2003

The detailed flow characteristics inside a compression chamber due to the orbiting motion of a scroll is studied numerically. The orbiting motion of a scroll is modelled at 7 orbiting angles. At each orbit angle, the central compression chamber is modelled. All computations are carried by using an in-house code. It is based on the SIMPLE algorithm. Computation results show that the flow structure inside the compression chamber is dependent on the orbit angle. The pressure variation inside the compression chamber also shows great dependence on the orbit angle. The pressure variation shows local maxima when the orbiting motion of a scroll directs toward the center of the compression chamber.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2007년도 추계학술대회 논문집
• /
• pp.161-162
• /
• 2007

• 한국전자파학회논문지
• /
• 제28권2호
• /
• pp.155-158
• /
• 2017

전자, 통신 기술의 발달로 대부분의 장소에서 전자기기가 존재한다. 자동차, 열차, 항공기 등 다양한 장소에서 전자기기의 활용이 증가된 만큼 고출력 전자기파로 인한 오작동과 하드웨어의 치명적인 손상을 확인할 수 있는 안전성을 연구하는 것이 중요하게 되었다. 구조물 내부에 전자기기 및 여러 센서를 연결하는 케이블은 전자기파에 의한 오작동을 초래할 수 있는 원인 중 하나이기 때문에 전자파 영향에 대한 해석이 필수적이다. 본 논문에서는 상관관계 함수와 전송이론을 이용하여, 전기적으로 큰 공진기 내부에 존재하는 케이블에 유기되는 전류를 계산해 외부 전자기파에 의한 영향을 해석하였다.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2009년 춘계학술대회논문집
• /
• pp.97-103
• /
• 2009

A numerical study of the flow characteristics inside a U-type circular tube is carried out in this paper. The numerical simulations carried out by using a Navier-Stokes code which is commercially available. Before detailed numerical simulations, validation of present numerical approach is made by comparing numerical solutions with experimental data. Numerical simulations are performed to study the effect of curvature on the flow characteristics inside a U-type tube. Numerical solutions show that a significant effect on the secondary flow structure in the cross section of the tube, especially in the curved section is shown when the curvature ratio, ratio of curvature to tube diameter, is smaller than about 3.5. As the curvature ratio decreases below 3.5, a counter rotating vortex is found below the primary vortex in the cross section of the tube. Another dramatic change of the flow structure is the formation of streamwise separation zone when the curvature ratio is decreased below 1.25.

• 한국전산유체공학회지
• /
• 제14권3호
• /
• pp.105-114
• /
• 2009

A numerical study of the flow characteristics inside a U-type circular tube is carried out in this paper. The numerical simulations carried out by using a Navier-Stokes code which is commercially available. Before detailed numerical simulations, validation of present numerical approach is made by comparing numerical solutions with experimental data. Numerical simulations are performed to study the effect of curvature on the flow characteristics inside a U-type tube. Numerical solutions show that a significant effect on the secondary flow structure in the cross section of the tube, especially in the curved section is shown when the curvature ratio, ratio of curvature to tube diameter, is smaller than about 3.5. As the curvature ratio decreases below 3.5, a counter rotating vortex is found below the primary vortex in the cross section of the tube. Another dramatic change of the flow structure is the formation of streamwise separation zone when the curvature ratio is decreased below 1.25.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회B
• /
• pp.2713-2717
• /
• 2008

Whole flow fields of a room air conditioner (RAC) have been visualized by a Particle Image Velocimetry (PIV) technique to analyze the flow structure with various inlet and outlet angles, and to control an eccentric vortex which affects an efficiency and noise of the RAC. A test model with 5 stages of a cross flow fan has been manufactured and a transparent acryl has been installed at the side of the test model for the PIV experiment. The inlet and outlet flows and the flow inside the cross flow fan have been analyzed by varying the inlet grill angles and outlet blade angles. The movement of the eccentric vortex has been investigated experimentally by developing the measurement technique for the inner flow field of the cross flow fan. From the visualization of the inner flows, the origins of the noise inside the RAC and the condensation points around the outlet parts of the cold air have been observed and the solution of the problems can be proposed in this study.

• 한국산업융합학회 논문집
• /
• 제21권5호
• /
• pp.257-263
• /
• 2018

It is a small injection molding machine for table top considering the material heating mechanism and the design and structure stability by securing the mechanism that compresses the inside of the material heating tube by using the electric actuator and by providing space between the body and the material heating tube to reduce heat loss Develop body. An electric actuator suitable for applying pressure to the inside of a material heating tube is a mechanical system composed of a rigid structure. Since a large force is repeatedly applied to the electric actuator and the push rod, the interaction between the moving parts and the dynamic Maximum stress through analysis and prediction of fatigue life of critical parts The pushrod reflects the structural analysis results of the electric actuator and the push rod, and pushes the inside of the material heating tube by the push rod to inject the molten material from the nozzle into the mold. The pushrod operates by the operation of the electric actuator. The material heated by the coil heater is ejected through the nozzle by the pressure of the material heating tube, and the material heating tube and the nozzle are also lowered at the same time as the push rod is lowered, so that the material is closely adhered to the mold. We want to study the completion of the injection.