• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집E
• /
• pp.158-161
• /
• 2001

A new type baghouse with tangential inlet and inner tube was developed and it's performances were evaluated. Experiments with variable shapes of inner tube were performed to suggest an optimum shape of inner tube which might decrease the dust loading onto bag filter surface and the amount of reentrained particles by internal gas flow. The dust loading was lower when inner tubes parallel to outer casing exist. When an inner tube covering around the lower portion of bag filters was used, the dust particles detached from the filter surface by cleaning process were reentraind by internal recirculating gas flow.

• 한국자동차공학회논문집
• /
• 제19권4호
• /
• pp.24-31
• /
• 2011

Performance of the asymmetric trapezoidal fin with various upper lateral surface slopes is investigated by using the two-dimensional analytic method. For a fin base boundary condition, convection from the inner fluid to the inner wall, conduction from the inner wall to the fin base and conduction through the fin base are considered. Heat loss and fin efficiency are represented as a function of the fin base thickness, base height, inner fluid convection characteristic number, fin tip length and fin shape factor. One of the results shows that heat loss increases while fin efficiency decreases as the fin shape factor increases.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2003년도 춘계학술대회 논문집
• /
• pp.1705-1708
• /
• 2003

The purpose of this study is to investigate the manufacturing technique on the U type Draw-Bending of inner grooved tube. This bending process make the U shape tube by Hair Pin Bending machine. The U type tube requires the quality of product that satisfy sufficient conditions for a heat exchanger. The mandrel components act the important roles that prevent wrinkles and keep the shape of cross section of bended tube at bending process. We performed the FEM simulation using LS-DYNA software and the bending test of inner groove tube and then, compared bending simulation with bending test results about mandrel ball diameter, mandrel position and optimal clearance between mandrel and tube.

• 한국의상디자인학회지
• /
• 제10권2호
• /
• pp.139-147
• /
• 2008

This study aims to investigate and analyze sewing methods according to the shape of the inner collar among women's jeogories in order to understand such sewing techniques, which has emerged during modern Korea, and has utilized diversly for the shape of the jeogori's inner collar and as part of the inner collar. The study was conducted on relics possessed between 1900 to 1990, or 515 pieces of jeogories. Jeogories were classified into single-layered and double-layered jeogories according to the shape of their composition. Inner collar shapes of jeogories have also been categorized. It was found that single-layered jeogories comprise 49 inner collars with shapes identical to those of the outer collars. Double-layered jeogories comprise of the following three types: 43 pieces of godae close, 18 pieces in which the inner collar of the outer bodice are cut without a connecting line and the inner collar of the godae and inner bodice are suspended, and 405 pieces in which the share of the inner collar is identical to that of the outer collar. From the shapes of inner collars mentioned above, the following sewing methods have been derived: 1. To sew the inner collar of single-layered jeogories, a seaming technique had been used. 2. Among the inner collars of a double-layered jeogori, godae close was sewn with only a short part of the godae by using a lining, and then finished with overage and blind stitches. Godae close was a covenient way to attach inner collars, and also saved much time. 3. Inner collars with shapes identical to the outer collar are divided into two groups: those with outer collars cut out fellowing the cloth without seam and shifted towards the linings and used as an inner collar, and those with outer collars made of outer linings and inner collar of inner linings. To sew the collar, paste and needlework had been employed, where the methods of needlework were divided into blind stitch, overage stitch, and catch stitch. In sewing with paste, only godae was blind stitched or overage stitched, and the remainder had been painted with paste or the collar had been finished with heated soldering iron after the entire inner collar was painted with paste.

• Journal of the Korean Wood Science and Technology
• /
• 제46권4호
• /
• pp.315-322
• /
• 2018

Bamboo culm comprises internodes and nodes and is tapered from the bottom to the top. Anatomically, bamboo culm comprises vascular bundles and parenchymal base tissue. The gross anatomical structure of a transverse section of any culm internode is determined by the shape, size, arrangement, and number of vascular bundles. The purpose of this research was to examine the morphology of culm and the distribution and shape of vascular bundles in Ampel bamboo (Bambusa vulgaris). Bamboo culms were harvested from the base. Test samples were obtained from a central 2-cm long segment of each internode across the entire length of the culm. Results showed an uneven spread of vascular bundles in the internode cross-section. Transitioning from the outer to the inner layer of the internode, the number of vascular bundles per unit area decreased and their shape was variable. The size of vascular bundles in the middle layer of the internode was greater than that of those in the outer and inner layers. The shape of vascular bundles was circular in the outer layer, which gradually transformed into vertical oval toward the middle layer and horizontal oval toward the inner layer. Vascular bundles were of type III and IV in the bottom of the culm and type III in the middle to the top of the culm.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제5권3호
• /
• pp.454-467
• /
• 2013

A practical Ship Inner Shell Optimization Method (SISOM), the purpose of which is to improve the safety of the seagoing transport ship by decreasing the maximum Still Water Bending Moment (SWBM) of the hull girder under all typical loading conditions, is presented in this paper. The objective of SISOM is to make the maximum SWBM minimum, and the section areas of the inner shell are taken as optimization variables. The main requirements of the ship performances, such as cargo hold capacity, propeller and rudder immersion, bridge visibility, damage stability and prevention of pollution etc., are taken as constraints. The penalty function method is used in SISOM to change the above nonlinear constraint problem into an unconstrained one, which is then solved by applying the steepest descent method. After optimization, the optimal section area distribution of the inner shell is obtained, and the shape of inner shell is adjusted according to the optimal section area. SISOM is applied to a product oil tanker and a bulk carrier, and the maximum SWBM of the two ships is significantly decreased by changing the shape of inner shell plate slightly. The two examples prove that SISOM is highly efficient and valuable to engineering practice.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1995년도 춘계학술대회논문집
• /
• pp.62-70
• /
• 1995

The inner pulley is automobile component used as airconditioner clutch assembly. in cold forging of the inner pulley . the design conditions are the same between inner length and outer length, the uniform hardness and the no shape change in inner fillet radius due toa piercing. In industries, the design of forging processes is performed based on an experience-oriented technology, that is, designer's experiences and expensive trial and error. Using the rigid -plastic finite element simulation, we propose the optimal process conditons and design of preform or redesign of final product shape without defects prodicted by metal flow, distribution fo strain, forging load during forging processes form initial workpiece to final product.

• 한국해양공학회지
• /
• 제26권6호
• /
• pp.66-73
• /
• 2012

A pressure compensated chamber of a pilot mining robot isolates and protects an electrical-electronic system from the ambient highly pressured water. Since the inner pressure of the chamber is compensated with outer water pressure using hydraulic oil and pressure compensator, there exists a pressure difference, less than 1 bar, between outer and inner surface. The structural safety of the chamber is obtained relatively easier than the canister type which inner pressure is kept as the atmospheric pressure. However, due to the adoption of box shape for space efficiency and usage of the transparent engineering plastic viewport for checking inner circumstance, the viewport can be largely deformed. This large deformation can cause an additional tensile force, called the prying force, to the bolt-flange connection parts of the viewport. In this paper, we suggest the structural design equation considering the prying action for designing the structure of a box-shape pressure compensated chamber.

• 자동차안전학회지
• /
• 제10권2호
• /
• pp.6-12
• /
• 2018

Optimized section shape of aluminum bumper backbeam for enhancing the front high speed crashworthiness was investigated. Front body analysis model of a convertible vehicle was built up and parameter studies were carried out with changing the inner rib shape and the section thickness distribution. First an inner rib shape displaying most efficient structural performance was selected. Next, for the selected section the effect of section thickness combination was examined. Also, a light weighed backbeam section displaying crash performance over the current design was suggested. Finally RCAR front low speed impact analyses were carried out for the optimized models.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2008년도 정기 학술대회
• /
• pp.495-498
• /
• 2008

In this paper applicable range of U-Channel Bridge (UCB) that has recently been introduced as a new bridge type was studied. For structural analysis models used with the frame and plate elements was proposed, and verification of the models were performed. Using these structural models structural analysis of models with span length of 20m-45m and inner width of 5m-13m were performed. As a result for U-shape sections were applicable in the range of 20m span and 35m span, slab was applicable in the range of 5m inner width and 12m inner width. To increase applicable range of UCB H-shape sections and slab with rib were proposed. As a result UCB were applicable in the range of 20m span and 45m span, in the range of 5m inner width and 13m inner width.