• 한국관개배수논문집
• /
• 제8권1호
• /
• pp.88-101
• /
• 2001

Flow through culvert is very complex depending on the characteristics of hydraulic conditions. A design method using a monograph is normally employed due to wide range of flow characteristics and the difficulty of calculating inlet water depth. The presen

• 물과 미래
• /
• 제25권2호
• /
• pp.99-110
• /
• 1992

담수화호에서는 온도 및 염도차에 의하여 성층류가 발생하며 수심이 깊은 담수화호의 경우 그 형상이 더욱 뚜렷하다. 본 연구는 깊은 담수화호를 대상으로 내부환경면이 잘 발달된 이층류에 있어서 저층배수관의 유출수 염분농도를 실험을 통하여 규명하였다. 실험에 이용된 저층배수관은 세가지 유형으로 유입층과 배수관의 유출수 염분농도차를 무차원으로 수식화 하였고 유입층의 상층부 흐름이 순간적으로 배수되는 밀도층의 한계조건을 밀도 Froude수와 배수관의 직경 및 수심의 함수로 방정식을 유도하였다.

• 한국안전학회지
• /
• 제33권4호
• /
• pp.119-126
• /
• 2018

In recent years, as flood damage caused by heavy rains increased, the great-depth tunnel using urban underground space is emerging as a countermeasure of urban inundation. The great-depth tunnel is used to reduce urban inundation by using the underground space. The drainage efficiency of great-depth tunnel depends on the intake design, which leads to increase discharge into the underground space. The spiral intake and the tangential intake are commonly used for the inlet facility. The spiral intake creates a vortex flow along the drop shaft and reduces an energy of the flow by the wall friction. In the tangential intake, flow simply falls down into the drop shaft, and the design is simple to construct compared to the spiral intake. In the case of the spiral intake, the water level at the drop shaft entrance is risen due to the chocking induced by the flowrate increase. The drainage efficiency of the tangential intake decreases because the flow is not sufficiently accelerated under low flow conditions. Therefore, to compensate disadvantages of the previously suggested intake design, the multi-stage intake was developed which can stably withdraw water even under a low flow rate below the design flow rate. The hydraulic characteristics in the multi-stage intake were analyzed by changing the flow rate to compare the drainage performance according to the intake design. From the measurements, the drainage efficiency was improved in both the low and high flow rate conditions when the multi-stage inlet was employed.

• Journal of Advanced Marine Engineering and Technology
• /
• 제28권8호
• /
• pp.1195-1202
• /
• 2004

In this paper an experimental study was investigated for two-phase flow distribution in compact heat exchanger header. A test section was consisted of the horizontal bottom dividing header($\phi$: 5 mm, L: 80 mm) and 10 upward circular mini channels ($\phi$: 1.5 mm, L: 850 mm) using an acrylic tube. Three different types of tube intrusion depth were tested for the mass flux and inlet mass quality ranges of 50 - 200 kg/$m^2$s and 0.1 - 0.3, respectively. Air and water were used as the test fluids. The distribution of vapor and liquid is obtained by measurement of the total mass flow rate and the calculation of the quality. Two-phase flow pattern was observed, and pressure drop of each channel was measured. By adjusting the intrusion depth of each channel an uniform liquid flow distribution through the each channel was able to solve the mal-distribution problem.

• 한국물환경학회지
• /
• 제23권5호
• /
• pp.748-755
• /
• 2007

To develop an efficient pump operating rule for a retard basin, it is necessary to estimate inflow to the retard basin accurately which is affected by the backwater effect at the outlet of the conduit. The magnitude of the backwater effect is dependent on the water depth of a retard basin; however, the depth is determined by the amount of inflow and outflow. Thus, a real time simulation system that is able to simulate urban runoff and the pump operation with the consideration of the backwater effect is required to estimate the actual inflow to a retard basin. With this system, the efficient pump operating rule can be developed to diminish the possible flood damage on urban areas. In this study, a realtime simulation system is developed using the SWMM 5.0 DLL and Visual Basic 6.0 equipped with EXCEL to estimate inflow considering the backwater effect. The realtime simulation can be done by updating realtime input data such as minutely observed rainfall and the depth of a retard basin. Using those updated input data, the model estimates actual inflow, the amount of outflow discharged by pumps and gates, the depth of each junction, and flow rate at a sewer pipe on realtime basis. The developed model was applied to the Joonggok retard basin and demonstrated that it can be used to design a sewer system and to estimate actual inflow through the inlet sewer to reduce the inundation risk. As results, we find that the model can contribute to establish better operating practices for the pumps and the flood drainage system.

• 한국물환경학회지
• /
• 제39권1호
• /
• pp.38-45
• /
• 2023

In this study, the removal efficiency of road sweeping and sand filter facility for removing total suspended solid (TSS) as nonpoint source pollution from expressway was evaluated for the last 10 years (2012~2021) using ROADMOD. ROADMOD is a screening level model and was calibrated for runoff rate and TSS loading both at the inlet, which is the loading from the drainage area, and the outlet, from the sand filter facility. The drainage area is 715 m² and the dimensions of sand filter facility are 1.5 m (wide) × 3.8 m (length) × 1.5 m (depth). The monitoring period for model calibration was the rainfall event during Aug. 31~Sep. 1, 2021 and the amount of rainfall was 74.5 mm. As a result of calibration, the determination coefficients (R²) of the flow rate were 0.66 and 0.86, for the inlet and outlet, respectively, and those of TSS loading were 0.50 and 0.84, for the inlet and outlet, respectively. Considering that ROADMOD is a screening level model, the calibration results were reasonable to evaluate the best management practices (BMPs) on the expressway. Using ROADMOD simulation results for 2012~2021, the average yearly runoff rate from the expressway was 82% and removal efficiency was 9% for road sweeping, 35% for sand filter facility, and 39% for both road sweeping and sand filter facility.

• Structural Engineering and Mechanics
• /
• 제63권4호
• /
• pp.567-574
• /
• 2017

Sedimentation tanks are essential structures to filter the suspended sediments in the inlet flow which are constructed at the inlet of the basins forked from rivers and irrigation canals. The larger the constructed tank, the better the sedimentation process is conducted. However, the construction and dredging costs increase. In this regard, improving the performance and sedimentation efficiency seem necessary by alternative methods. One of these effective methods is using baffle plates. Most of the studies carried out in this field are on the use of these baffles in the primary and secondary sedimentation tanks. Hence, this study is carrier out with the objective of increasing the retention efficiency in the irrigation sedimentation tanks using baffles. To reach this goal, the experiments were carried out in a flume with length 8 meters, width 0.3 meters, and height 0.5 meters, considering a sedimentation tanks with a length of 3 meters, in three different inlet concentration, three flow rates and three Froude numbers. The baffles were mounted at the bottom of the tank and the effects of the angle, height and position in the tanks were investigated. The results showed that on average, employing the baffles increased the sedimentation efficiency 5 to 6% and the highest value was obtained for angle 60 with respect to the flow direction. According to the results of this study, the most favorable height and position of these baffles were obtained to be in 40% of the depth of the flow and 50% of the length of the sedimentation tank, respectively. Also, by increasing the number of baffles, the sedimentation efficiency decreased. Regarding the sedimentation regions in this case, more than 80% of the settled sediments were observed in the middle of the tank measured from the inlet.

• 한국환경복원기술학회지
• /
• 제15권5호
• /
• pp.129-144
• /
• 2012

This study was conducted to understand the community characteristics of benthic macroinvertebrates according to Growth Environment at 6 Palustrine Wetlands in a rural area. As growth environment factors, size, water depth, water inlet and water outlet, land-use and water environment was analyzed. Two years' quantitative collection of benthic macroinvertebrate was carried out, and it executed community analysis and ESB index calculation and also carried out twinspan, MDS and correlation analysis. As a result, the collected benthic macroinvertebrate was 1254 individuals with 3 Phylums, 6 Classes, 14 Orders, 35 Families, 52 Genera and 61 Species. Odonata and Coenagreionidae had the highest species and individuals. Dominance Index was 0.252~0.698, Diversity Index was 1.661~2.902, Evenness Index was 0.414~0.724, and Species Richness Index was 1.990~6.224. As a result of community analysis, when correlation analysis was executed, Dominance Index had the opposite tendency with Diversity Index and Evenness Index, which had the same tendency with the previous studies. When ESB Index was calculated, Grade 2 (polluted) had the highest species with 48 species (78.7%). It is determined from the Environmental quality evaluation and saprobity evaluation result according to ESB index that there is a need to revise environmental evaluation system more specifically. As a result of MDS analysis, the subject spots A and D had the highest similarity, and the subject spot E and D had a relatively high similarity. The life environment that is the closest related with species diversity is estimated by the land-use. As for number of Individual, it seems to have the closest relation with inlet, which is to be determined as a characteristics of Palustrine Wetland. Through such investigation, this study is expected to be utilized for various types of habitats including ecological pond and to be utilized for the increase of species diversity in rural areas.

• International Journal of Fluid Machinery and Systems
• /
• 제7권4호
• /
• pp.174-182
• /
• 2014

The ultimate objective of this study is to develop a water turbine appropriate for low-head open channels to effectively utilize the unused hydropower energy of rivers and agricultural waterways. The application of a cross-flow runner to open channels as an undershot water turbine has been considered and, to this end, a significant simplification was attained by removing the turbine casing. However, the flow field of an undershot cross-flow water turbine possesses free surfaces, and, as a result, the water depth around the runner changes with variation in the rotational speed such that the flow field itself is significantly altered. Thus, clear understanding of the flow fields observed with free surfaces to improve the performance of this turbine is necessary. In this study, the performance of this turbine and the flow field were evaluated through experiments and numerical analysis. The particle image velocimetry technique was used for flow measurements. The experimental results reflecting the performance of this turbine and the flow field were consistent with numerical analysis. In addition, the flow fields at the inlet and outlet regions at the first and second stages of this water turbine were clarified.

• 상하수도학회지
• /
• 제21권1호
• /
• pp.131-138
• /
• 2007

A rainwater utilization facility consists of its catchment area, treatment facility, storage tank, supply facility and pipes in general. The rainwater storage tank which occupies the largest area of the facility has been usually considered quantitatively for determining the storage capacity. Hence, there is little information on water quality improvement by sedimentation in a rainwater storage tank in operation. In this study, we measured the rainwater quality in a rainwater storage tank in operation during late spring and summer, and showed water quality improvement of turbidity removal of 25~46% by sedimentation in a rainwater storage tank under a fixed water level without inflow and outflow after runoff ceased. It is necessary to have a considerable distance between the inlet and outlet of the tank and, if possible, it is recommended that the design should allow for an effective water depth of over 3 m and supply rainwater near the water surface. The operation method which increases the retention time by stopping rainwater supply for insuring low turbidity is recommended when the turbidity of rainwater runoff is high. And also more efficient operation and maintenance of the rainwater utilization facility is expected through the tailored design and operation of the facility considering particle removal and behavior.