• 제목/요약/키워드: initial crack length

검색결과 104건 처리시간 0.028초

평활시험편에 있어서 균혈형상비 변화에 따른 표면균열의 피로수명과 균열관통거동 (The Fatigue Life and Penetration Behavior by Variety of Aspect Ration on Smooth Specimen)

  • 남기우;엄윤성
    • 수산해양기술연구
    • /
    • 제28권2호
    • /
    • pp.197-207
    • /
    • 1992
  • Fatigue life and penetration behavior were examined analytically by variety of initial front face crack length and initial crack depth. The fatigue crack shape before penetration is almost semielliptical, and the aspect ratio by calculation using the Newman-Raju's formula is smaller than the value obtained by the experiment. It is found that the crack growth behavior on the back surface after penetration is unique and can be divided into three stage a, b and c. By using the K value proposed by the authors, particular crack growth behavior and the change in crack shape can be evaluated quantitatively. It is found that fatigue life and penetration behavior were more dependent on initial front face crack length than initial crack depth.

  • PDF

일반구조용 압연강재의 부식피로균열전파거동에 미치는 시험편 두께의 영향 (Effect of Specimen Thickness to Corrosion Fatigue Crack Propagation Behavior of Structure Rolled Steel)

  • 조약래
    • 수산해양기술연구
    • /
    • 제28권3호
    • /
    • pp.286-294
    • /
    • 1992
  • In this paper, the corrosion fatigue crack propagation behavior of structure rolled steel (SWS 41C) was investigated by changing the thickness, and this experiment was done by the three point bending corrosion fatigue tester. The main results obtained are as follows: 1) As the thickness of specimen becomes thicker, the corrosion sensitivity to initial stage crack becomes some sensitive, and that the fatigue life becomes more sensitive. 2) The crack growth rate to initial stage crack (da/dN) was retarded as the thickness of specimen becomes thicker. But after initial stage crack, as the thickness of specimen is more thicker, da/dN is more rapid. 3) As the corrosion fatigue crack length grows, the accelerative factor of thick specimen (t=12mm) is more higher than that of thin specimen (t=6mm). 4) As the corrosion fatigue crack length grows, the corroson potential of both thick specimen and thin specimen becomes more less noble potential, however thick specimen (t=12mm) tends to more less noble potential than that of thin specimen(t=6mm).

  • PDF

초기 균열길이 및 섬유방향이 CFRP/GFRP 하이브리드 적층재의 층간 파괴에 미치는 영향 (The Effects of the Initial Crack Length and Fiber Orientation on the Interlaminar Delamination of the CFRP/GFRP Hybrid Laminate)

  • 권오헌;권우덕;강지웅
    • 한국안전학회지
    • /
    • 제28권1호
    • /
    • pp.12-17
    • /
    • 2013
  • Considering the wind power system and the rotor blades which are composed of much technology, the wind power blade would be the most dangerous part because it revolves at high speed and weighs about dozens of tons, if the accident happens. Therefore, the light weight composite materials have been replacing as substitutional materials. The object of this study is to examine the delamination and damage for CFRP/GFRP hybrid composite that is used for strength improvement of a wind power blade. The influence of the initial crack length and fiber orientation for the interlaminar delamination was exposed for the blade safety. Plain woven CFRP instead of GFRP was inserted into the layer of the box spar for improving the strength and blade life. DCB(Double Cantilever Beam) specimen was used for evaluating fracture toughness and damage evaluation of interlaminar delamination. The material used in the experiment is a commercial material known as CF 3327 EPC in plain woven carbon prepreg(Hankuk Carbon Co.) and UD glass fiber prepreg(Hyundai Fiber Co.). From the results, crack growth rate is not so different according to the variation of the initial crack length. Mode I interlamainar fracture toughness of fiber direction $0^{\circ}$ is higher than that of $45^{\circ}$. Interlaminar fracture has an effect on fiber direction and K decreased with lower value according to increasing initial crack length. Also energy release rate fracture toughness was evaluated because CFRP/GFRP hybrid composite with a different thickness is under the mixed mode loading condition. The interlaminar fracture was almost governed by mode I fracture even though the mixed mode.

Effect of initial coating crack on the mechanical performance of surface-coated zircaloy cladding

  • Xu, Ze;Liu, Yulan;Wang, Biao
    • Nuclear Engineering and Technology
    • /
    • 제53권4호
    • /
    • pp.1250-1258
    • /
    • 2021
  • In this paper, the mechanical performance of cracked surface-coated Zircaloy cladding, which has different coating materials, coating thicknesses and initial crack lengths, has been investigated. By analyzing the stress field near the crack tip, the safety zone range of initial crack length has been decided. In order to determine whether the crack can propagate along the radial (r) or axial (z) directions, the energy release rate has been calculated. By comparing the energy release rate with fracture toughness of materials, we can divide the initial crack lengths into three zones: safety zone, discussion zone and danger zone. The results show that Cr is suitable coating material for the cladding with a thin coating while Fe-Cr-Al have a better fracture mechanical performance in the cladding with thick coating. The Si-coated and SiC-coated claddings are suitable for reactors with low power fuel elements. Conclusions in this paper can provide reference and guidance for the cladding design of nuclear fuel elements.

응력집중부를 갖는 표면균열재의 균열길이 변화에 따른 피로거동 (The Fatigue Behavior by Variety of Crack Length of Surface Cracked Plate with Stress Concentration Part)

  • 남기우;김선진
    • 한국해양공학회지
    • /
    • 제9권1호
    • /
    • pp.83-91
    • /
    • 1995
  • Surface defects in structural members are apt to be origins of fatigue cracks growth, which may cause serious failure of whole structures. Most structure has a part where stress concentrates such as welded joints, corner parts, etc. And then, analysis on crack growth and penetration from these defects, therefore, is one of the most important subjects for the reliability of LBB design. The present paper has performed an experimental and analysis on the fatigue crack propagation by variety in crack length of surface cracked plate with stress concentration part. The crack growth behavior can be explained quantitatively by using Newman-Raju equation and the stress partitioning method proposed by ASME B&P Code Sec. XI. The stress concentration factor $K_t$ has affected on the crack growth. The crack growth after penetration depends upon the initial front side crack length.

  • PDF

세라믹스의 피로수명에 대한 통계적 분석 (Statistical Analysis for Fatigue Lifetime of Ceramics)

  • 박성은;김성욱;이홍림
    • 한국세라믹학회지
    • /
    • 제34권9호
    • /
    • pp.927-934
    • /
    • 1997
  • Static and cyclic fatigue tests were carried out for alumina specimen to study the statistical analyses (normal, lognormal and Weibull distribution) of fatigue lifetime data and nominal initial crack length data. Fatigue lifetime data followed Weibull distribution better than normal or lognormal distribution, for the shape parameter of the notched specimen was larger than that of the unnotched specimen. The nominal initial crack length data obtained from fatigue lifetime followed the lognormal and Weibull distribution better than normal distribution, for the coefficient of variation of the unnotched specimen was larger than that of the notched specimen, and shape parameter of unnotched specimen was smaller than that of the notched specimen.

  • PDF

휨응력을 받는 바닥강판의 피로균열진전해석 (Fatigue Crack Growth Analysis of Steel Deckplates Under Bending Stress)

  • 최준혁;경갑수;최동호;장동일
    • 한국강구조학회 논문집
    • /
    • 제11권4호통권41호
    • /
    • pp.409-416
    • /
    • 1999
  • 반복하중을 받는 용접구조물의 피로수명 추정에 있어서 파괴역학을 이용한 피로균열 진전해석방법은 매우 유용하다. 휨응력을 받는 바닥강판의 피로균열 진전해석 문제에서는 균일한 축하중 하에서의 피로균열 진전해석 절차를 동일하게 적용할 수 있다. 본 연구에서는 휨응력하에서 피로균열 진전수명을 계산하는 방법을 제시하고 2차원 균열 문제에서의 피로균열 진전을 다루었다. 수치적으로 계산된 균열진전은 균열길이가 증가함에 따라 피로균열의 진전속도가 점차 감소하고 실험결과와 잘 일치하였다. 피로 수명은 초기균열길이와 균열형상에 따라 달라짐을 알 수 있었다.

  • PDF

콘크리트의 축압축강도에 대한 크기효과 (Size Effect on Axial Compressive Strength of Concrete)

  • 이성태;김민욱;김진근
    • 콘크리트학회논문집
    • /
    • 제13권2호
    • /
    • pp.153-160
    • /
    • 2001
  • 본 연구에서는 콘크리트 부재에서의 축압축강도에 대한 크기효과를 검토하였다. 이를 위하여 두 가지 대표적인 압축파괴모드 중의 하나인 모드 I 파괴에 대한 실험적 연구를 이중 캔틸레버 보를 이용하여 수행하였다. 각 캔틸레버의 축에 대한 작용하중의 편심거리와 초기 균열길이를 변화시킴에 의하여 콘크리트의 축압축강도에도 크기효과가 존재하는 지의 여부를 확인하였고, 최소자승법을 이용하여 수정된 크기효과법칙의 새로운 실험상수들을 제시하였다. 연구결과로부터 초기 균열이 있는 콘크리트 부재의 축압축강도에도 크기효과가 존재함을 확인하였다. 하중의 편심거리에 있어서는 균열선단에서의 인장과 압축응력의 영향이 매우 중요하며 이 경우에 뚜렷한 크기효과가 나타났다. 즉 균열선단에서 인장응력의 영향이 증가하면 콘크리트의 크기효과는 증가한다. 그러나 초기 균열길이의 경우, 축압축강도의 크기효과에 미치는 영향은 존재하지만 균열길이에 따른 차이는 뚜렷하지 않았는데 이는 고강도 콘크리트 부재의 경우 부재의 세장비 차에도 불구하고 파괴진행영역의 크기가 서로 비슷한데 그 원인이 있는 것으로 판단된다.

Al/Epoxy 이종재 접합 계면의 초음파 감쇠계수에 의한 균열길이의 측정 (Measurement of Crack Length by Ultrasonic Attenuation Coefficients on Interfaces of Al/Epoxy Bonded Dissimilar Materials)

  • 박성일;정남용
    • 대한기계학회:학술대회논문집
    • /
    • 대한기계학회 2003년도 추계학술대회
    • /
    • pp.1109-1114
    • /
    • 2003
  • The initial crack often occurs on the bonded interface and it is the general cause of the interface fracture. It is very significant to establish the measurement method of interfacial crack by applying the ultrasonic technology into the interface of bonded dissimilar materials. In this paper, the interfacial crack length was measured by ultrasonic attenuation coefficient in the Al/Epoxy bonded dissimilar materials of double-cantilever beam(DCB). The energy release rate, G, was obtained by the experimental and Ripling's equation measurement of compliance. The experimental results represent that the relation between interfacial crack length for the ultrasonic attenuation coefficient and energy release rate is increased proportionally. From the experimental results, a measurement method of the interfacial crack length by the ultrasonic attenuation coefficient was proposed and discussed.

  • PDF

연성 균열성장 개시의 미시적 파괴조건 (Microscopic fracture criterion of crack growth initiation)

  • 구인회
    • 대한기계학회논문집
    • /
    • 제11권5호
    • /
    • pp.740-745
    • /
    • 1987
  • 본 연구에서는 파괴조건(4)와 유사하게 임계 스트레인 조건을 사용하나 기존 스트레인이 없는 재료의 날카로운 균열선단을 가진 시편의 파괴인성실험치(.delta.$_{IC}$)로 부터 재료의 고유상수인 특성길이를 결정하는 방법이 제안되었다.이 파괴조건을 이 용하여 처음노치선단의 유한한 반경과 재료의 기존 스트레인이 시편의 파괴개시에 미 치는 영향을 예측하고자 한다.