• 연구논문집
• /
• s.30
• /
• pp.5-13
• /
• 2000

The computation scheme of simulating gas turbine transient behavior was developed. The basic principles of this scheme and main input data required are described. Calculation results are presented in terms of whole operating regime of the cycle. The influence of main initial parameters such as starting engine power, moment of inertia of the rotor, fuel supplying schedule etc. on performance characteristics of has turbine during transient operation is studied In addition, bleeding air influence on transient behavior was also considered For validation of the developed code, comparison of present calculation with that of measurement data of the experimental data for the range of operating period studied.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.11a
• /
• pp.81-84
• /
• 2000

In this paper, we have the investigated the Influence of Filler Shape on Dielectric & Electric Charge-Discharge Properties of Filled Epoxy Resin. In the low frequency range from 50Hz to a few kHz, the magnitude of tan$\delta$ become larger in the order, NON, RAS, SAS, SCS. The electrical Discharge of RAS measured for 60 min, decreased after 10$^2$∼10$^3$.

• Proceedings of the KIPE Conference
• /
• 1998.10a
• /
• pp.598-602
• /
• 1998

This paper refers to fundamental investigations and simulations of conducted electromagnetic inference emissions produced by power electronic devices in a frequency range from 2 to 10 kHz. The emissions of different industrial power converters were measured and compared. The influence of different working conditions over the altitude of the EMI are represented. Simulations of the power converter system including the line impedance stabilisation network certify the measurements.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.707-710
• /
• 2009

As the inner diameter of CCFL is increased in the range of outer diameters 3~5 mm, the luminance efficiency is increased by the low power consumption. For the outer diameter 5 mm, the efficiency is linearly increased even at the range of a high current.

• Journal of the Korean Society of Safety
• /
• v.28 no.5
• /
• pp.71-77
• /
• 2013

This Study aims at investigating actual condition on attending school road of children and analyzing empirically the characteristics of cognition and the influence of safety on school road. This study findings are as follows : 1) Walking alone to go to school is the highest rates among Commuting Mode, and Commuting distance to school is nearly doubles than range of school zone(300 m). 2) Among characteristics of urban spatial structure affecting on influence classify safety of school road, 'Commuting Distance' has been drawn to most influential variable. Especially, there are 4 types classified by commuting distance and it became obvious that the longer the distance, the lower the safety score(under 127 m=76.9 points, Over 451 m=58.3 points). 3) As a result of investigating the influence of Safety on attending school road, Vehicle commuting speed urder 127 m as internal of school zone, and Walking and crossing convenience over 451 m as external of school zone have a lot of influence on safety cognition on school road. Therefore Safety on school road should be considering the commuting distance to school among surrounding characteristics, needed for improvement plan and program based on real safety cognition of children.

• Proceedings of the KSME Conference
• /
• 2007.05b
• /
• pp.2775-2780
• /
• 2007

The ballistic range has long been employed in a variety of engineering fields such as high-speed impact engineering, projectile aerodynamics and aeroballistics, since it can create very high-pressure states in a short time. Since the operation of the ballistic range includes many complicated processes, each should be studied in detail for the best operation of the device. One of the main processes which have a major influence in its operation is the compression of the driver gas. Most of the studies available in this field hardly discuss this process in detail and thus lack a proper understanding of its effect. In the present study, a computational analysis has been made to investigate the compression process in the pump tube of a ballistic range. The results obtained are validated with some experimental data. It is seen that the pump tube parameters and the piston mass significantly affect the compression process and the time to build up the required diaphragm rupture pressure.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.11
• /
• pp.2944-2953
• /
• 1994

Active range finders using laser beam have been widely used for the factory automation and quality assurance, but they may be unreliable if the object' slope is steep or its surface is specular. The reliability of an active range finder was analyzed for the variation of the reflected laser beam intensity. First, the properties of the object's reflection were modeled by using the bidirectional reflectance-distribution function(BRDF), and then the variation of the laser beam brightness was formulated for the different configuratioin of the object and sensor. The experimental data of the laser beam reflection were obtained for two materials, mild steel and stainless steel. The parameters of the proposed model were obtained by fitting the data of the mild steel to the model and it was found that the results calculated from the proposed model were in good agreement with the experimental data.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1994.11a
• /
• pp.147-151
• /
• 1994

In order to investigate the dielectric characteristic insulating oil is chosen insulating oil for electric cable, and experiment is performed in the temperature range of 30∼120[$^{\circ}C$] and frequency range of 30∼1${\times}$10$\^$6/[㎐]. As a result, the observed linear decrease in tan $\delta$ value at the low frequency range is due to the influence of frequency, whereas the increase in tan $\delta$ value at high frequency range is contributed by the electrode's resistance and dielectric loss. The dipole moment and activation energy of specimen are obtained 1.22(debye) and 12.75∼18.66[㎉/㏖e] of high temperature region, 15.68 ∼ 20.6[㎉/㏖e] of low temperature region respectively.

• Nuclear Engineering and Technology
• /
• v.55 no.7
• /
• pp.2489-2497
• /
• 2023

Co and Eu impurities in the SSCs are nuclides that dominantly influence the neutron-induced radioactive inventory in metal and concrete radwastes (radioactive wastes) during NPP decommission. The impurity concentrations provided by NUREG/CR-3474 were used for the practical range of Co and Eu impurity concentrations to be applied to the code calculations. Metal structures near the core were evaluated to be ILW (intermediate-level waste) for the whole range of Co impurity concentration, so the boundary line between ILW and LLW (low-level waste) has no change for the whole concentration range provided by NUREG/CR-3474. Also, the boundary line between VLLW (very low-level waste) and CW (clearance waste) in the concrete shield could alter a little depending on the Eu impurity concentration within the range provided by NUREG/CR-3474. From this work, it is found that the concentration of material impurities of SSCs gives no critical impact on determining radwaste levels.

• Journal of the Korean Institute of Gas
• /
• v.22 no.3
• /
• pp.38-44
• /
• 2018

Ammonia is used primarily as a refrigerant in refrigeration facility and SCR of a plant, and is frequently involved in leakage accidents. This study was conducted by selecting ammonia, a material with a wide influence range when evaluated, as a material with higher vapor pressure and lighter than air. In this study, the influence ranges were computed using KORA(Korea Off-site Risk Assessment supporting tool) with four different environmental factors : ground roughness, sealing, operating temperature, pressure, and leakage hole size. As a result, the difference in the influence range of ground roughness is approximately 4.62 times, while the ammonia storage tank shows a difference in the reduction rate of 0.64 when sealed. The extent of impact increased with increasing leakage depending on storage temperature and pressure, and when storing higher than the saturation vapor pressure, the impact range showed an average growth rate of 3.45 % per 0.1 Mpa($45^{\circ}C$). The influence ranges based on the size of the leakage holes is shown to be proportional to the area of the leakage zone.