• Transactions on Control, Automation and Systems Engineering
• /
• v.2 no.1
• /
• pp.56-61
• /
• 2000

Majority of industrial robots are controlled by a simple independent joint control of joint actuators rather than complex controllers based on the nonlinear dynamic model of the robot manipulator. In this independent joint control scheme, the performance of actuator control is influenced significantly by the joint disturbance torques including gravity, Coriolis and centrifugal torques, which result in the trajectory tracking error in the joint control system. The control performance of a redundant manipulator under independent joint control can be improved by minimizing this joint disturbance torque in resolving the kinematic redundancy. A 3 DOF planar robot is studied as an example, and the dynamic programming method is used to find the globally optimal joint trajectory that minimize the joint disturbance torque over the entire motion. The resulting solution is compared with the solution obtained by the conventional joint torque minimization, and it is shown that joint disturbance can be reduced using the kinematic redundancy.

• Journal of Institute of Control, Robotics and Systems
• /
• v.19 no.1
• /
• pp.45-55
• /
• 2013

With the recent advancement of control method and battery technology, the electric vehicle have been researched to replace the conventional vehicle with electric vehicle with the view point of the environmental concerns and energy conservation. An electric vehicle which is equipped with the independent front steering system and in-wheel motors has advantage in terms of control. For example, the different torque which generated by left and right wheels directly can make yaw moment and the independent steering using outer wheel control is able to reduce the sideslip angle. Using of independent steering and driving system, the 4 wheel electric vehicle can improve a performance better than conventional vehicle. In this paper, we consider the method for improving the cornering performance of independent front steering system and in-wheel motor used electric vehicle with the compensated outer wheel angle and direct yaw moment control. Simulation results show that the method can improve the cornering performance of 4 wheel electric vehicle. We also apply the steering motor failure to steer the vehicle turned by the torque difference without steering. This paper describes an independent front steering and driving, consist of three parts; Vehicle Model, Control Algorithm for independent steering and driving and simulation. First, vehicle model is application of TruckSim software for independent front steering and 4 wheel driving. Second, control algorithm describes the reduced sideslip and direct yaw moment method in view of cornering performance. Last is simulation and verification.

• Proceedings of the KIEE Conference
• /
• 1998.11b
• /
• pp.435-437
• /
• 1998

In this productive system, it needs to control the each axis motion harmoniously to perform accurately for the manufacturing, transporting and printing. Independent Axis Control usually used for this objection. However, if Independent Axis Control mismatched the parameter of each axis system or in the case of free curve tracking or the case of high speed control, there would be big contour error so that cannot achieve control objection. As a result, there is Contour Control method suggested to supply for this defect. This paper carried modeling of biaxial system and implemented Independent Axis Control & Contouring Control on straight line, circular, and coner path by simulation and experiment. If feedrate increased, contour error growed. In consequence, according to this factor, we introduced contouring controller, so we could find the fact that contour error was reduced more than that of independent axis control about each path.

• Journal of the Korean Society for Precision Engineering
• /
• v.19 no.2
• /
• pp.126-132
• /
• 2002

Robot manipulator has highly nonlinear dynamics. Therefore the control of multi-link robot arms is a challenging and difficult problem. In this paper an independent joint adaptive fuzzy sliding mode scheme is developed leer control of robot manipulators. The proposed scheme does not require an accurate manipulator dynamic model, yet it guarantees asymptotic trajectory tracking despite gross robot parameter variations. Numerical simulation for independent joint control of a 3-axis PUMA arm will also be included.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.28 no.12
• /
• pp.95-102
• /
• 2014

This paper proposes a coordinated control for an independent multi-phase transverse flux linear synchronous motor (IM-TFLSM) based on magnetic levitation. The stator structures of the IM-TFLSM are composed of a two set, which has independent three-phase windings and a double-sided air-gap as opposed to the conventional Y-connected three-phase linear motors. A suitable control algorithm is necessary to operate the applied linear machine. This study proposes a coordinated control algorithm for adjusting the mover air-gap and thrust force of the IM-TFLSM in order to maintain air-gap and phase shifted current control of the independent 3-phase modules. In addition, the principle of operation and its special structures are described in detail and the validity and effectiveness of the control algorithm is verified through multiple experimental results.

• Journal of Power Electronics
• /
• v.16 no.5
• /
• pp.1773-1780
• /
• 2016

This paper proposes a wide air-gap control method for the multi-module permanent magnet linear synchronous motor (MM-PMLSM) based on independent vector control. In particular, the MM-PMLSM consists of symmetrical multi-module and multi-phase structures, which are basically three-phase configurations without a neutral point, unlike conventional three-phase machines. In addition, there are no additional magnetic levitation windings to control the normal force of the air-gap between each stator and mover. Hence, in this paper, a dq-axis current control applying a d-q transformation and an independent vector control are proposed for the air-gap control between the two symmetric stators and mover of the MM-PMLSM. The characteristics and control performance of the MM-PMLSM are analyzed under the concept of vector control. As a result, the proposed method is easily implemented without additional windings to control the air-gap and the mover position. The effectiveness of the proposed independent vector control algorithm is verified through experimental results.

• Journal of Power Electronics
• /
• v.14 no.1
• /
• pp.115-124
• /
• 2014

This paper presents the implementation of two-arm modulation (TAM) technique for the independent control of a two-induction motor drive fed by a five-leg inverter (FLI). A carrier-based space vector pulse width modulation technique for TAM is proposed to generate switching signals for FLI. Two independent three-phase space vector modulators are utilized to control two motors. The motor drive system applies two separate indirect field-oriented control methods. The stationary voltage outputs from the vector control are synthesized in the three-phase space vector modulator to generate switching signals for FLI. The performance of the independent control of the motors and the voltage utilization factor are likewise analyzed. Simulation and experimental results verify the effectiveness of the proposed method for the independent control of the two-motor drive system. The proposed technique is successfully validated by dSPACE DS1103 experimental work.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.16 no.3
• /
• pp.240-249
• /
• 2013

This paper discusses the maneuvering control algorithm based on all-wheel independent driving and steering control techniques for special purpose 6WD/WS vehicles. The maneuvering control algorithms considering superior dynamic characteristics of high power in-wheel motors and independent steering system are designed to perform driving, steering, vehicle stability, and fault tolerant control. The maneuvering controller applies sliding and optimal control theories considering optimal torque distribution and friction circle related to the vertical tire force. The fault tolerant control algorithm is applied to obtain the similar maneuverability to that of the non-faulty vehicle. The simulations using the Matlab/Simulink dynamics model and experiments using HIL simulator mounting the real controllers with the designed control algorithms prove the improved performances in terms of vehicle stability and maneuverability.

• Journal of Institute of Control, Robotics and Systems
• /
• v.9 no.12
• /
• pp.994-1000
• /
• 2003

A new relative motion control methodology for a following system to an independent leading system is proposed for controlling relative position, velocity, and tension etc. It is based on maintaining minimum relative error between two independent systems. The control command of the following system to a leading system is generated by adding the current command and the output of the relative error compensation. The proposed control method is implemented on the experimental equipment which is a wire winding-unwinding system to control the tension of the line. The results show the unwinding system(follower) following the independent motion of the winding system(leader) to control the constant tension of the line in order to keep the roller dancer in reference position. The relative motion control method proposed in this paper can be applied to high precision equipment for unwinding and winding fine wire, fine fiber, and tape etc.

• Journal of Institute of Control, Robotics and Systems
• /
• v.17 no.4
• /
• pp.313-320
• /
• 2011

Multi-axle driving vehicles that are used in special environments require high driving performance, steering performance, and stability. Among these vehicles, 6WS/6WD vehicles with middle wheels have structural safety by distributing the load and reducing the pitch angle during rapid acceleration and braking. 6WS/6WD vehicles are favored for military use in off road operations because of their high maneuverability and mobility on extreme terrains and obstacles. 6WD vehicles that using in-wheel motor can generate the independent wheel torque without other mechanical parts. Conventional vehicles, however, cannot generate an opposite driving force at each side wheel. Using an independent steering and driving system, six-wheel vehicles can show better performance than conventional vehicles. Using of independent steering and driving system, the 6 wheel vehicle can improve a performance better than conventional vehicle. This vehicle enhances the maneuverability under low speed and the stability at high speed. This paper describes an independent 6WS/6WD vehicle, consists of three parts; Vehicle Model, Control Algorithm for 6WS/6WD and Simulation. First, vehicle model is application of TruckSim software for 6WS and 6WD. Second, control algorithm describes the optimum tire force distribution method in view of energy saving. Last is simulation and verification.