• Journal of the Korean Wood Science and Technology
• /
• 제20권2호
• /
• pp.61-72
• /
• 1992

This study was carried out to investigate the fracture behavior and the fracture criterion of yellow lauan(Shorea spp.), when has used for furniture and wood structures, and to offer a reliability for wood structure and basic data for wood fracture criterion in experiments which are fracture tested under mode I, mode II and mixed mode loading condition. The results were summarized as follows; 1. Fractures in specimens which have inclined grain in yellow lauan procedeed from crack tip in the radial direction along the grain. 2. In yellow lauan, $K_{IC}RL$ was 42.1kg/$cm^{3/2}$ and $K_{IIC}RL$ was 15.8kg/$cm^{3/2}$. 3. The fracture criteria of lauan were; ($K_I/K_{IC}$)+($K_{II}/K_{IIC}$)=1 in RL system with inclined grain at $45^{\circ}$, ($K_I/K_{IC}$)+$(K_{II}/K_{IIC})^2$=1 with inclined grain at $15^{\circ}$ and $(K_I/K_{IC})^2$+$(K_{II}/K_{IIC})^2$=1 with inclined grain at $30^{\circ}$, $60^{\circ}$, $75^{\circ}$ and $90^{\circ}$, respectively. 4. The fracture criterion of wood could vary with the species, and the load applying condition. In order to measure the fracture criterion strictly, along with standardization of specimen geometry a large amount of experimental data is needed. 5. $K_{IC}$(critical stress intensity factor) can be predicted by grain angle. As the grain inclined angle increased, $K_{IC}$ and $K_{IIC}$ are increased.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 춘계학술대회 논문집
• /
• pp.1253-1256
• /
• 2005

An Experiment was carried out to study burr minimization in drilling on the inclined exit surface. Several different drills, exit surface angles and cutting conditions were selected to determine their influences on burr formation. In drilling operation, there are not only flat exit surfaces but also inclined exit surfaces which is described as inclination angle. Inclination of exit surface causes a quiet different burr formation when comparing with flat surface. Burr formation mechanisms are analyzed according to the drill geometries and cutting conditions. Several schemes for burr minimization on inclined exit surface were proposed. Burr geometry in each drill and cutting condition are measured by laser measurement system.

• 한국자동차공학회논문집
• /
• 제6권6호
• /
• pp.234-242
• /
• 1998

It has been demonstrated that the in-cylinder turbulence is enhanced by inclined swirl with a SCV(swirl control valve). The inclined-tumble flow measurement and analysis were performed for various types of intake systems that generated several different combinations of swirl ratio and tumble ratio in the cylinder. Experiments were conducted in a 4-valve optically accessed transparent research engine using a backward-scatter LDV mode under motoring condition at 1,000rpm. The influence of swirl/tumble levels on the characteristics of turbulence was analysed. This study presents experimental results of the inclined-tumble flow structure, including the flow motion phenomena, angular momentum and turbulence intensity.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2003년도 봄 학술발표회 논문집
• /
• pp.241-248
• /
• 2003

In August 2002, side wall of OO tunnel, at the Bonghwa, Kungbuk province, Korea, was collapsed by abruptly applied heavy soil and water pressure to side wall from a inclined shaft when there was a heavy rain. These days, Inclined shaft is used for the purpose of reducing construction time, using ventilation system, using the out of carrying equipment and mucking when we construct tunnel in the world. Recently constructed tunnel has the source of inclined shafts, but the more time elapse, we lose the source of the inclined shaft such as exact position, condition, and the fact that whether inclined shaft is exist or not. Therefore, this study inspected the interior's appearance, analyzed structure to evaluate the reason of collapsing side wall and this study also performed the repairing work. Finally, we show improving maintenance method to prevent that similar accident that might be happened.

• 대한기계학회논문집
• /
• 제14권3호
• /
• pp.624-635
• /
• 1990

본 연구에서는 마멸과정을 선형파괴역학적 관점에서 해석하여, 탄성체의 표면 에 산재되어 있는 표면균열의 전파거동을 마멸과정규명의 입장에서 살펴보고자 한다. 우선 마멸거동에 관한 파괴역학적 접근방식에 의한 마멸이론의 확립을 위해서, 표면균 열이 내부균열보다 그 전파 가능성이 높다고 한 Keer등의 주장에 착안하여 Hertz 접촉 압력하의 경사진 표면균열의 전파거동을 선형파괴역학적으로 해석하고자 한다. 이론 해석에 있어서는 표면균열을 인상전립의 연속분포로 치환하고, 전립밀도분포함수에 관 한 특이적분방정식을 유도해서 Erdogangupta의 방법을 이용하여 그 해를 구하였다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집D
• /
• pp.433-439
• /
• 2001

An experimental study was carried out on the characteristics of the mixed-convection heat transfer from a protruding heat source module which had uniform heat flux and was located on a flat plate in the inclined channel. The effects of the inclined channel(${\varphi}=0{\sim}90^{\circ}$) was studied for the input power($Q=3,\;7W$) and inlet air velocities($V_{i}=0.1{\sim}0.9m/s$). Experimental results indicate that the input power was most effective parameter on the temperature differences between inlet air and module. The effects of the inclined angle was negligible when the inlet velocities were above 0.5m/s and 0.9m/s at Q = 3W, 7W respectively. As the inclined angle of the channel increases, the temperatures of the module are decreased. So we obtained the best condition on the adiabatic board at the vertical channel.

• 한국지능시스템학회논문지
• /
• 제20권5호
• /
• pp.617-623
• /
• 2010

본 논문에서는 차륜형 역진자에 적용되는 LMI 제어기 설계와 그 수치 시뮬레이션이 수행되었다. 차륜형 역진자는 2개의 평형점을 갖고 있는 역진자의 일종이다. 불안정한 평형점에 대하여 평형을 유지하기 위하여 차륜형 역진자는 지속적으로 제어되어야 한다. 경사면을 고려하여 차륜형 역진자의 동역학 방정식이 유도되었다. 경사면을 적극적으로 고려하여 차륜형 역진자를 안정화 시킬 수 있는 제어기를 구성하는데 선형행렬부등식 기법이 적용되었다. LMI 기반 제어기가 평면과 경사면에 대해서 유효함을 보이기 위해서 다양한 수치 시뮬레이션이 수행되었다.

• 한국해양공학회지
• /
• 제18권6호
• /
• pp.79-83
• /
• 2004

The curved blocks which compose the bow and stem of a ship contain many skewed joints that are inclined horizontally and vertically. Most of these joints have a large fitness error and are continuously changing their form and are not easily accessible. The welding position and parameter values should be appropriately set in correspondence to the shape and the inclination of the joints. The welding parameters such as current, voltage, travel speed, and melting rate, are related to each other and their values must be in a specific limited range for the sound welding. These correlations and the ranges are dependent up on the kind and size of wire, shielding gas, joint shape and fitness. To determine these relationships, extensive welding experiments were performed. The experimental data were processed using several information processing technologies. The regression method was used to determine the relationship between current voltage, and deposition rate. When a joint is inclined, the weld bead should be confined to a the limited size, inorder to avoid undercut as well as overlap due to flowing down of molten metal by gravity. The dependency of the limited weld size which is defined as the critical deposited area on various factors such as the horizontally and vertically inclined angle of the joint, skewed angle of the joint, up or down welding direction and weaving was investigated through a number of welding experiments. On the basis of this result, an ANN system was developed to estimate the critical deposited area. The ANN system consists of a 4 layer structure and uses an error back propagation learning algorithm. The estimated values of the ANN were validated using experimental values.

• 한국멀티미디어학회논문지
• /
• 제15권5호
• /
• pp.606-614
• /
• 2012

AdaBoost 알고리즘을 이용한 얼굴 검출 방법은 가장 빠르고 신뢰성 있는 얼굴 검출 알고리즘의 하나로 이를 향상하거나 확장한 많은 알고리즘들이 제안되었다. 그러나 이전의 접근들은 대부분 정면 얼굴만을 다루고 있고 AdaBoot 알고리즘을 정면과 기울어진 얼굴에 동일한 특징으로 적용함으로써 기울어진 얼굴에 대한 분별 성능이 제한적이었다. 또한 회전된 얼굴을 검출하기 위하여 입력된 영상을 회전하여 정면 얼굴 검출 방법을 적용하거나 회전된 각도에 따라 다른 검출기를 적용하는 기존 기법들은 연산량이 많고 검출률이 저하되는 문제를 가지고 있다. 본 논문에서는 이러한 문제를 극복하기 위해 JointBoost를 이용한 기울어진 얼굴 검출 방법을 제안한다. JointBoost를 통해 클래스간의 공유된 feature들를 찾음으로써 연산량과 샘플 복잡도를 감소시켰다. 실험 결과를 통해 제안된 방법의 검출률이 동일한 반복 횟수를 가지는 학습에서 기존의 AdaBoost 기법에 비해 2% 이상 우수함을 보인다. 또한 제안된 방법은 얼굴의 존재를 검출할 뿐만 아니라 기울어진 방향에 대한 정보도 제공할 수 있다.

• 대한토목학회논문집
• /
• 제28권5B호
• /
• pp.591-594
• /
• 2008

본 연구에서는 사각격자체계를 이용하는 수치해석기법을 대상으로 격자내에 생성되는 경사면의 합리적인 처리 및 경계조건을 검토하기 위하여 사각격자내에 존재하는 불투과성 및 투과성구조물의 경사면에 대한 새로운 처리기법과 경계조건을 제안한 후, 파 구조물 해저지반/해빈의 상호간섭을 직접 해석할 수 있는 3D-수치모델(LES-WASS-3D; 허와 이, 2007)을 이용하여 수치계산을 실시하였다. 이로부터 얻어진 계산결과와 종래의 계단식 격자구성을 이용한 수치해석결과를 비교 검토하여 제안한 사각격자내의 경사면 처리기법에 대한 타당성을 검증하였다.