• Journal of the Microelectronics and Packaging Society
• /
• v.12 no.4 s.37
• /
• pp.281-287
• /
• 2005

in-situ electromigration test was carried out for edge drift lines of eutectic SnPb solder using Scanning Electron Microscopy (SEM). The electromigration test for the eutectic SnPb solder sample was conducted at temperature of $90^{\circ}C$ and the current density of $6{\times}10^4A/cm^2$. Edge drift at cathode and hillock growth at anode were observed in-situ in a SEM chamber during electromigration test. It was clearly revealed that eutectic SnPb solder lines has an incubation stage before void formation during electromigration test, which seemed to be related to the void nucleation stage of flip chip solder electromigration behaviors.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1994.11a
• /
• pp.106-108
• /
• 1994

Electromigration(EM) tests were carried out on Al and Cu films in HV systems to study surface migration. The Al films were made on oxidized silicon wafers by thermal evaporation, in-situ annealed at 300$^{\circ}C$, patterned, and EM tested at 260$^{\circ}C$ and 4.5MA/$\textrm{cm}^2$. SEM observation with back scattered electron mode on the EM tested Al films disclosed that thinning took place under the native Al oxide. In the case of Cu films, tested using in-situ TEM, thinning was also observed at the early stage of void formation even though the thinned areas were much less than those of the Al films.

• Applied Microscopy
• /
• v.24 no.3
• /
• pp.87-93
• /
• 1994

In order to elucidate the machinability of lead brass, orthogonal machining experiment was conducted in SEM(Scanning Electron Microscope) equipped with a micro-machining device at a cutting speed of $7{\mu}m/s$ for brass containing 0.2 to 3wt% Pb. The microfactors (i.e., shear angle, contact length between chip and tool) were determined by in-situ observations. Machinability of brass containing lead is discussed in terms of the microfactors and the cutting resistant force tested by lathe cutting. The dynamic behavior of the chip formation of lead brass during the machining process was examined: The chips of lead brass form as a shear angle type. The shear angle increases with the content of lead in (6:4) brass. The pronounced effect of lead on the contact length between chip and tool was observed above 1% Pb. The cutting resistant force tested by lathe decreases remarkably with the lead content in brass. The observed microfactors are in close relation to the tested resistant force in macromachining.

• Journal of the Korean Society for Precision Engineering
• /
• v.14 no.9
• /
• pp.146-154
• /
• 1997

Ion implantation has been used successfully as a surface treatment technology to improve the wear. fatigue and corrosion resistances of materials. A modified surface layer by ion implantation is very thin(under 1 m), but it has different mechanical properties from the substrate. It has also different wear characteristics. Since wear is a dynamic phenomenon on interacting surfaces with relative motion, an effective method for investigtating the wear of a thin layer is the observation of wear process in microscopic detail using in-situ system. The change of wear properties produces the transition of wear mode. To know the microscopic wear mechanism of this thin layer, it is very important to clarify its microscopic wear mode. In this paper, using the SEM and AFM Rribosystems as in-situ system, the microscopic wear of Ti ion-implanted 1C-3Cr steel, a material for roller in the cold working process, was investigated in repeated sliding. The depth of wear groove and the speciffc wear amount were changed with transition of microscopic wear mode. The depth of wear groove with friction cycles in AFM tribosystem and specific wear amount of Ti ion-implanted 1C-3Cr steel were less about 2-3 times than those of non-implanted 1C-3Cr steel. The microscopic wear mechansim of Ti ion-implanted 1C-3Cr steel was also clarified. The microscopic wear property was quantitatively evaluated in terms of microscopic wear mode and specific wear amount.

• 한국생물공학회:학술대회논문집
• /
• 2005.10a
• /
• pp.860-863
• /
• 2005

The microcapsules containing fragrant oil as functional material were prepared by in-situ polymerization with prepolymer that was made from melamine-formaldehyde (MF) as wall material of microcapsules. The effects of polymerization variables, such as the nature and concentration of surfactants, stirring rate, and stirring time, on the size and distribution of the particles were investigated. Fourier transform-infrared spectroscopy (FT-IR), thermal analysis, particle size analysis, scanning electron microscopy (SEM) observation were used to investigate the characteristics of microcapsules. Through the FT-IR and SEM analysis, we found that the prepared microcapsules were containing fragrant oil and the shape of particle was spherical. The nature and concentration of surfactants, stirring rate, and stirring time had profound effects on the particle size and particle size distribution.

• Nuclear Engineering and Technology
• /
• v.52 no.10
• /
• pp.2394-2401
• /
• 2020

Octadecylamine is an effective film-forming amine that protects carbon steel from corrosion. In the present study, the effect of octadecylamine concentration on adsorption on a carbon steel surface was investigated in anaerobic alkaline solution by using SEM/EDS, TEM and the Materials Studio simulation techniques. TEM morphology observation and EDS elemental detection determine the thicknesses of octadecylamine film on a carbon steel surface, which are confirmed by the in-situ electrochemical impedance spectroscopy measurement and resistance calculation. The Materials Studio simulation reveals the number of octadecylamine film layers at different concentrations. Results obtained in this study indicate that adsorption of octadecylamine film on carbon steel proceeds with the multi-layer adsorption mechanism.

• Progress in Superconductivity
• /
• v.9 no.1
• /
• pp.68-73
• /
• 2007

We fabricated the in-situ $MgB_2$ wires using the powder-in-tube method and investigated the effects of sintering temperature and SiC contents on the microstructure and superconducting properties. Pure $MgB_2$ wires and 5, 10, 20 wt.% SiC doped $MgB_2$ wires were sintered at $600-1000^{\circ}C$ for 30 minutes in Ar atmosphere. We found that $MgB_2$ phase was mostly formed at the sintering temperature of $700^{\circ}C$ and above, and the critical temperature ($T_c$) increased with increasing sintering temperature. For the $MgB_2$ sintered at $850^{\circ}C$, the highest critical current density ($J_c$) was obtained to be $3.7{\times}10^5\;A/cm^2$ at 5 K and 1.6 T by a magnetic properties measurement system (MPMS). The addition of SiC to the $MgB_2$ wires changed microstructure and critical properties. SEM observation showed that the $MgB_2$ core had considerable micro-cracks in undoped wire and the density of micro-cracks decreased with increasing SiC contents. The critical temperature decreased as the SiC contents increased, on the other hand, the critical current density of SiC doped $MgB_2$ wires in high magnetic field was enhanced compared to that of undoped $MgB_2$ wires.

• Journal of Powder Materials
• /
• v.20 no.1
• /
• pp.53-59
• /
• 2013

Fe-TiC composite powder was fabricated via two steps. The first step was a high-energy milling of FeO and carbon powders followed by heat treatment for reduction to obtain a (Fe+C) powder mixture. The optimal condition for high-energy milling was 500 rpm for 1h, which had been determined by a series of preliminary experiment. Reduction heat-treatment was carried out at $900^{\circ}C$ for 1h in flowing argon gas atmosphere. Reduced powder mixture was investigated by X-ray Diffraction (XRD), Field Emission-Scanning Electron Microscopy (FE-SEM) and Laser Particle Size Analyser (LPSA). The second step was a high-energy milling of (Fe+C) powder mixture and additional $TiH_2$ powder, and subsequent in-situ synthesis of TiC particulate in Fe matrix through a reaction of carbon and Ti. High-energy milling was carried out at 500 rpm for 1 h. Heat treatment for reaction synthesis was carried out at $1000{\sim}1200^{\circ}C$ for 1 h in flowing argon gas atmosphere. X-ray diffraction (XRD) results of the fabricated Fe-TiC composite powder showed that only TiC and Fe phases exist. Results from FE-SEM observation and Energy-Dispersive X-ray Spectros-copy (EDS) revealed that TiC phase exists uniformly dispersed in the Fe matrix in a form of particulate with a size of submicron.

• Parasites, Hosts and Diseases
• /
• v.23 no.2
• /
• pp.203-213
• /
• 1985

The in situ posture of anterior body of Metagonimus yokogawai was observed in experimental metagonimiasis of dog. The metacercariae were collected from naturally infected sweetfish by peptic digestion; a total of 8 dogs was orally infected with 10,000 metacercariae respectively. Two dogs were killed on 3 days, 9 days, 4 weeks and 10 weeks after the infection. The postures of worms in histological section of small intestine and of whole worms collected from the fixed intestinal mucosa were examined by light and scanning electron microscope. The results were summarized as follows: 1. The recovery rates of worms were 42.6% on 3 days, 55.0% on 9 days, 33.2% on 4 weeks and 9. 8% on 10 weeks after the infection respectively. 2. In histological sections of small intestine, most of worms were found at intervillous spaces as ovoid sections of posterior body. However, many worms, especially in 3 day-old worms, revealed protruded anterior body in glandular lumens of crypt. Some sections of anterior body were bifurcated or sacculated. 3. The worms collected from fixed intestinal mucosa under dissecting microscope exhibited a variety of postures. Many worms showed flat shapes with a concavity or curvatures. However, in many worms, the anterior body made a single or multiple protrusions. 4. By SEM observation of protruded anterior body, a longitudinal groove was found. 5. The frequency of worms with protruded anterior body decreased in 9 days, 4 weeks and 10 weeks than in 3 day-old worms. The above findings indicated that the anterior body of juvenile and adult M. yokogawai protruded to lumens of glandular crypt by folding their lateral portions to make a reversible tubelike structure. Frequent multiple protrusions were considered to be made to adapt the microniche of glandular crypts of dog intestine.

• Journal of Life Science
• /
• v.17 no.9 s.89
• /
• pp.1284-1289
• /
• 2007

The Biological Activated Carbon (BAC) process in the water treatments represents a kind of biofiltration process which capabilities of bacteria to remove organic matters are maximized. It enables to eliminate organic matters and effectively reduce microbial regrowth potentials. As attached bacteria employ natural organic matter as a substrate, they are significantly dependent on indigenous microorganisms. In this study, characteristics of bacterial community by culturable and unculturable Methods have been conducted in a pilot plant using SAC in water treatment process at the downstream of the Nakdong River. Based on the results, HPC and bacterial- production for coal-based activated carbon material were $1.20{\sim}56.2{\times}l0^7$ cfu/g and $1.2{\sim}3.7\;mgC/m^{3}h$, respectively, in the SAC process. The highest level of attached bacteria biomass and organic carbon removal efficiency was found in the coal-based activated carbon. The genera Pseudomonas, Flavobacterium, Alcaligenes, Acilzetobacter, and Spingomonas were identified for each activated carbon material. Pseudomonas vesicularis was the dominant species in the coconut- and coal-based materials, where as Pseudomonas cepacia was the dominant species in the wood-based material. The Scanning Electron Microscope (SEM) observation of the activated carbon surface also found the widespread distribution of rod form and coccus. The community of attached bacteria was investigated by performing Fluorescent in situ hybridization (FISH) analysis. a group was dominant in coal, wood and coccunt-based materials, ${\alpha},\;{\beta}\;and\;{\gamma}$ group ranged from 27.0 ${\sim}$ 43.0%, 7.1 ${\sim}$ 22.0%, 11.3 ${\sim}$ 28.6%, respectively. These results suggest that a group bacterial community appears to be regulated removal efficiency of organic material in water treatment process.