• Tribology and Lubricants
• /
• 제14권4호
• /
• pp.114-120
• /
• 1998

The T-curve, wear and erosion behaviors of two different silicon carbides, i.e., the fine grained SiC and the in situ-toughened SiC(IST-SiC). Both materials exhibited an increasing T-curve behavior, although the T-curve of IST-SiC was steeper than that of fine grained SiC. The fracture toughness of IST-SiC was larger than that of fine grained SiC at long crack regime, whereas an opposite tendency occurred at short crack regime. The rate of material removal during wear and erosion tests was higher in IST-SiC compared to fine grained SiC. The difference between the material removal rates of two materials was discussed in the light of their R-curve behaviors.

• 한국세라믹학회지
• /
• 제44권4호
• /
• pp.189-193
• /
• 2007

Effect of additive composition on fracture toughness of in situ-toughened $SiC-Si_3N_4$ composites was investigated for five different additive compositions. The highest toughness $(6.4MPa{\cdot}m^{1/2})\;in\;SiC-Si_3N_4$ composites investigated herein was obtained when an Y-Mg-Si-Al-O-N oxynitride glass was used as a sintering additive. The improvement in fracture toughness was produced by enhanced bridging and deflection by $Si_3N_4$ grains.

• 한국세라믹학회:학술대회논문집
• /
• 한국세라믹학회 2000년도 춘계총회,특별강연,심포지움,연구발표회
• /
• pp.44.1-44.1
• /
• 2000

• 한국세라믹학회지
• /
• 제38권12호
• /
• pp.1075-1079
• /
• 2001

The R-curve for in situ-toughened SiC-30 wt% TiC composites was estimated by the indentation-strength method and compared to that of monolithic SiC with toughened microstructure. Both materials exhibited rising R-curve behavior. The SiC-TiC composites, however, displayed better damage tolerance and higher resistance to crack growth. Total volume fractions of SiC key grains, which take part in toughening mechanisms such as crack bridging and crack deflection, were 0.607 for monolithic SiC ceramics and 0.614 for SiC-TiC composites. From the microstructural characterization and the residual stress calculation, it was inferred that this superior performance of SiC-TiC composites can be attributed to stress-induced microcracking at heterophase (SiC/TiC) boundaries and some contribution from carck deflection by TiC grains.

• 한국세라믹학회:학술대회논문집
• /
• 한국세라믹학회 2000년도 춘계총회,특별강연,심포지움,연구발표회
• /
• pp.43.2-43.2
• /
• 2000

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1998년도 제27회 춘계학술대회
• /
• pp.139-145
• /
• 1998

This paper addresses the R-curve properties, wear resistance, and erosion resistance of the two silicon carbide ceramics with different microstructures, i.e. , fine grained SiC and in situ-toughened SiC(IST SIC). Fine grained SiC exhibits a relatively flat R-curve behavior whereas the IST SiC exhibits a increasing R-curve behavior. The increasing R-curve behavior in IST SiC is attributed to relatively weak grain boundaries. The rate of material removal during wear tests and erosion tests was higher for IST SiC than that for fine grained SiC. This is attributed to the weaker grain boundaries in IST SiC than that in fine grained SiC. It is implied that fracture toughness in short crack regime should be taken into consideration in the interpretation of the microscopical material removal process. We show that the higher the strength of grain boundaries is, the higher wear and erosion resistances are.

• 한국세라믹학회:학술대회논문집
• /
• 한국세라믹학회 2000년도 춘계총회,특별강연,심포지움,연구발표회
• /
• pp.45.1-45.1
• /
• 2000

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2000년도 추계학술대회논문집 - 한국공작기계학회
• /
• pp.386-391
• /
• 2000

It is known that Si$_3$N$_4$ceramic insert has less hardness than A1$_2$O$_3$ceramic insert. But Si$_3$N$_4$ceramic insert has not only high toughness and strength but also low thermal expansion coefficient, which makes it has longer tool life under thermal stress condition. In this study, commercial Si$_3$N$_4$ ceramic insert and home-made SiC-Si$_3$N$_4$ceramic insert which has different sintering time and chemical composition is tested under various cutting conditions. The experimental result is compared in terms of tool life and cutting force. Generally, As the cutting speed and the feed rate increased, the cutting force and the flank wear increased too. The performance of SiC-Si$_3$N$_4$ceramic insert shows the possibility to be a new ceramic tool.

• The Korean Journal of Ceramics
• /
• 제2권3호
• /
• pp.152-156
• /
• 1996

Fine (~0.09 $\mu$m) $\beta$-SiC Powders with 3.3wt% of large (~0.44$\mu$m) $\alpha$-SiC of $\beta$-SiC particles (seeds) added were hotpressed at 175$0^{\circ}C$ using $Y_2O_3$, $Al_2O_3$ and CaO as sintering aids and then annealed at 185$0^{\circ}C$ for 4 h to enhance grain growth. The resultant microstructure and polytypes were analyzed by high resolution electron microscopy (HREM).Growth of $\beta$-SiC with high density of microtwins and formation of ${\alpha}/{\beta}$ composite grains consisting of $\alpha$-SiC domain sandwiched between $\beta$-SiC domains were found in both specimens. When large $\alpha$-SiC (mostly 6H) seeds were added, the $\beta$-SiC transformend preferentially to the 6H polytype. In contrast, when large $\beta$-SiC (3C) seeds were added, the fine $\beta$-SiC transformed preferentially to the 4H polytype. Such results suggested that the polytype formation in SiC was influenced by crystalline form of seeds added as well as the chemistry of sintering aids. The ${\alpha}/{\beta}$ interface played and important role in the formation of elongated grains as evidenced by presence of ${\alpha}/{\beta}$ composite grains with high aspect ratio.

• 한국안광학회지
• /
• 제5권2호
• /
• pp.207-210
• /
• 2000

일축가압 소결 및 열처리하여 SiC-TiC 안경렌즈 절삭용 재료를 제조하였다. TiC의 함량은 0, 10, 20, 30wt%이었다. 일축가압소결 후 열처리한 안경렌즈 절삭용 복합재료의 미세구조는 TiC의 양에 크게 의존하였다. TiC의 함량이 증가할수록 파괴인성값이 증가됨을 알 수 있었다. 광학현미경과 X-ray 회질분석을 통하여 미세구조와 상분석을 하였다. 시편의 미세구조는 길게자란 SiC입자와 기지형의 TiC입자로 구성되었다. 본 연구에서 연구된 안경렌즈 절삭용 시편의 대표적인 경도와 파괴인성은 각각 14.9GPa과 $5.7MPa{\cdot}m^{1/2}$이었다.