• Proceedings of the Korean Geotechical Society Conference
• /
• 2009.09a
• /
• pp.463-471
• /
• 2009

Cemented soils or concrete are usually cured under moisture conditions and their strength increases with curing time. An insufficient supply of water to cemented soils can contribute to hydration process during curing, which results in the variation of bonding strength of cemented soils. In this study, by the consideration of in situ water supply conditions, cemented sand with cement ratio less than 20% was prepared by air dry, wrapped, and underwater conditions. A series of unconfined compression tests were carried out to evaluate the effect of curing conditions on the strength of cemented soils. The strength of air dry curing specimen was higher than those of wrapped cured specimen when cement ratio was less than 10%, whereas it was lower when cement ratio was greater than 10%. Regardless of cement ratio, air dry cured specimens were stronger than underwater cured specimens. A strength increase ratio with cement ratio was calculated based on the strength of 4% cemented specimen. The strength increase ratio of air dry cured specimen was lowest and that of wrapped and underwater cured ones increased by square. Strength of air dry cured specimen dropped to maximum 30% after wetting when cement ratio was low. However, regardless of cement ratio, strength of wrapped specimens dropped to an average 10% after wetting.

• Journal of Ginseng Research
• /
• v.41 no.3
• /
• pp.290-297
• /
• 2017

Background: The use of X-ray phase-contrast microtomography for the investigation of Chinese medicinal materials is advantageous for its nondestructive, in situ, and three-dimensional quantitative imaging properties. Methods: The X-ray phase-contrast microtomography quantitative imaging method was used to investigate the microstructure of ginseng, and the phase-retrieval method is also employed to process the experimental data. Four different ginseng samples were collected and investigated; these were classified according to their species, production area, and sample growth pattern. Results: The quantitative internal characteristic microstructures of ginseng were extracted successfully. The size and position distributions of the calcium oxalate cluster crystals (COCCs), important secondary metabolites that accumulate in ginseng, are revealed by the three-dimensional quantitative imaging method. The volume and amount of the COCCs in different species of the ginseng are obtained by a quantitative analysis of the three-dimensional microstructures, which shows obvious difference among the four species of ginseng. Conclusion: This study is the first to provide evidence of the distribution characteristics of COCCs to identify four types of ginseng, with regard to species authentication and age identification, by X-ray phase-contrast microtomography quantitative imaging. This method is also expected to reveal important relationships between COCCs and the occurrence of the effective medicinal components of ginseng.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.18 no.4
• /
• pp.304-309
• /
• 2015

To evaluate the degree of contamination caused by oil spill accident in the sea, the in-situ sensors which are based on the scientific method are needed in the real site. The sensors which are based on the fluorescence detection theory can provide the useful data, such as the concentration of oil. However these kinds of sensors commonly are composed of the ultraviolet (UV) light source such as UV mercury lamp, the multiple excitation/emission filters and the optical sensor which is mainly photomultiplier tube (PMT) type. Therefore, the size of the total sensing platform is large not suitable to be handled in the oil spill field and also the total price of it is extremely expensive. To overcome these drawbacks, we designed the fluorimeter for the oil spill detection which has compact size and cost effectiveness. Before the detail design process, we conducted the experiments to measure the excitation and emission spectrum of oils using five different kinds of crude oils and three different kinds of processed oils. And the fluorescence spectrometer were used to analyze the excitation and emission spectrum of oil samples. We have compared the spectrum results and drawn the each common spectrum regions of excitation and emission. In the experiments, we can see that the average gap between maximum excitation and emission peak wavelengths is near 50 nm for the every case. In the experiment which were fixed by the excitation wavelength of 365 nm and 405 nm, we can find out that the intensity of emission was weaker than that of 280 nm and 325 nm. So, if the light sources having the wavelength of 365 nm or 405 nm are used in the design process of fluorimeter, the optical sensor needs to have the sensitivity which can cover the weak light intensity. Through the results which were derived by the experiment, we can define the important factors which can be useful to select the effective wavelengths of light source, photo detector and filters.

• Journal of the Korean institute of surface engineering
• /
• v.45 no.1
• /
• pp.15-19
• /
• 2012

Tris(8-quinolinolato)aluminum(III); $Alq_3$ has been frequently used as an electron transporting layer in organic light-emitting diodes. Either Ba with a low work function or Au with a high work function was deposited on $Alq_3$ layer in vacuum. And then, the behaviors of electron transition at the $Alq_3$/Ba and $Alq_3$/Au interfaces were investigated by using the near edge x-ray absorption fine structure (NEXAFS) spectroscopy. In the each interface, the energy levels of unoccupied obitals were assigned as ${\pi}^*$(LUMO, LUMO+1, LUMO+2 and LUMO+3) and ${\sigma}^*$. And the relative intensities of these peaks were investigated. In an oxygen atom composing $Alq_3$ molecule, the relative intensities for a transition from K-edge to LUMO+2 were largely increased as Ba coverage (${\Theta}_{Ba}$, 2.7 eV) with a low work function was in-situ sequentially increased on $Alq_3$ layer. In contrast, the relative intensities for the LUMO+2 peak were reduced as Au coverage (${\Theta}_{Au}$, 5.1 eV) with a high work function were increased on $Alq_3$ layer. This means that the electron transition by photon in oxygen atom which consists in the unoccupied orbitals in $Alq_3$ molecule, largely depends on work function of a metal. Meanwhile, in the case of electron transition in a carbon atom, as ${\Theta}_{Ba}$ was increased on $Alq_3$, the relative intensity from K-edge to ${\pi}_1{^*}$ (LUMO and LUMO+1) was slightly decreased, and from K-edge to ${\pi}_2{^*}$ (LUMO+2 and LUMO+3) was somewhat increased. This rising of the energy state from ${\pi}_1{^*}$ to ${\pi}_2{^*}$ exhibits that electrons provided by Ba would contribute to the process of electron transition in the $Alq_3$/Ba interfaces. As shown in above observation, the analyses of NEXAFS spectra in each interface could be important as a basic data to understand the process of electron transition by photon in pure organic materials.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.29 no.7
• /
• pp.523-531
• /
• 2018

An analysis technique for detecting moving targets on a single-channel airborne frequency-modulated continuous-wave (FMCW) technology and synthetic aperture radar (SAR) image is presented. To analyze the relative velocities of moving targets, an FMCW-based signal model for stationary and moving targets was studied, and a SAR ambiguity function considering its signal model was simulated. The relative velocities of the moving targets on a reconstructed SAR image can be estimated by peak searching of the SAR ambiguity function, and the stationary and moving targets are easily distinguished when there is a large variation of the relative velocity. Analysis results of the moving targets on a reconstructed FMCW-SAR image, using practical airborne data and a SAR ambiguity process, are compared with the in situ testing in the study area.

• International Journal of Highway Engineering
• /
• v.6 no.4 s.22
• /
• pp.25-33
• /
• 2004

The waste concrete produced by the process of the highway construction and management, has been crushed in-situ, and the waste aggregate has been experimentally used for anti-freezing layer and lean concrete. After testing the bearing capacity on anti-freezing layer, it was found that when the waste aggregates mixed with natural sand would be within the required gradations, the layer meets the requirements of limitation and the percentage to passing 2$\sim$20mm sieve increased by 5$\sim$13% because the flimsy mortars on aggregate were re-crushed by vibrated-roller compactor. The compressive strength of lean concrete using recycled aggregate was 71$\sim$85% of the natural coarce aggregate made, but nevertheless the recycled aggregates are applicable to the lean concrete because they largely exceeded the required strength, $57.5kgf/cm^2$.

• Journal of the Korean Geotechnical Society
• /
• v.30 no.4
• /
• pp.101-106
• /
• 2014

The penetration testing provides 1 dimensional profiles of properties applicable to limited investigation areas, although N-value has been linked to a wide range of geotechnical design parameters based on empirical correlations. The nondestructive test using elastic waves is able to produce 2 or 3 dimensional property maps by inversion process with high efficiency in time and cost. As both N-value and elastic wave velocities share common dominant factors that include void ratio, degree of saturation, and in-situ effective stress, the correlation between the two properties has been empirically proposed by previous studies to assess engineering properties. This study presents the experimentally measured elastic wave velocities of Jumunjin sands under at-rest lateral displacement condition with varying the initial void ratio and degree of saturation. Results show that the stress condition predominantly influences the wave velocities whereas void ratio and saturation determine the stress-velocity tendency. The correlation among the dominant factors is proposed by multiple regression analysis with the discussion of relative impacts on parameters.

• Korean Chemical Engineering Research
• /
• v.43 no.5
• /
• pp.603-608
• /
• 2005

The molded macroporous poly (glycidyl methacrylate-co-ethylene glycol dimethacrylate) rods produced by a facile molding process were polymerized in situ within a tubular mold, chromatographic column ($4.6{\times}100mm$) by free radical polymerization. It was complemented by epoxy derivatized monolithic column and chemical modification of the epoxide groups with the sulphuric acid. By variation of the polymerization conditions, such as the ratio of the monomers, the porogen (pore generating material), and the temperature, the pore size could be varied, so the retention time of the samples may be adjusted. For the mixture of caffeine and tryptophan in the prepared monolithic column, the influences of polymerization material compositions to the efficiency, selectivity, and resolution of the monolithic column were investigated.

• Macromolecular Research
• /
• v.14 no.5
• /
• pp.552-558
• /
• 2006

Biodegradable nanofibrous poly(L-lactic acid) (PLLA) scaffold was prepared by an electrospinning process for use in tissue regeneration. The nanofiber scaffold was treated with oxygen plasma and then simultaneously in situ grafted with hydrophilic acrylic acid (AA) to obtain PLLA-g-PAA. The fiber diameter, pore size, and porosity of the electrospun nanofibrous PLLA scaffold were estimated as $250\sim750nm,\;\sim30{\mu}m$, and 95%, respectively. The ultimate tensile strength was 1.7 MPa and the percent elongation at break was 120%. Although the physical and mechanical properties of the PLLA-g-PAA scaffold were comparable to those of the PLLA control, a significantly lower contact angle and significantly higher ratio of oxygen to carbon were notable on the PLLA-g-PAA surface. After the fibroblasts were cultured for up to 6 days, cell adhesion and proliferation were much improved on the nanofibrous PLLA-g-PAA scaffold than on either PLLA film or unmodified nanofibrous PLLA scaffold. The present work demonstrated that the applications of plasma treatment and hydrophilic AA grafting were effective to modify the surface of electrospun nanofibrous polymer scaffolds and that the altered surface characteristics significantly improved cell adhesion and proliferation.

• Journal of Soil and Groundwater Environment
• /
• v.18 no.6
• /
• pp.32-37
• /
• 2013

The scope of this study was to develop, design, and build an ex-situ remediation system of using the heating and water sparging treatment for the highly volatile DNAPL (Dense Non-Aqueous Phase Liquid) contaminated groundwater, and to conduct pilot testing at the site contaminated with DNAPL. The TCE (Trichloroethylene) removal was at the highest rate of 94.6% with the water sparging at $70^{\circ}C$ in the lab-scale test. The pilot-scale remediation system was developed, designed, and fabricated based on the results of the lab-scale test conducted. During the pilot-scale testing, DNAPL-contaminated groundwater was detained at heat exchanger for the certain period of time for pre-heating through the heat exchanger using the thermal energy supplied from the heater. The heating system supplies thermal energy to the preheated DNAPL-contaminated groundwater directly and its highly volatile TCE, $CCl_4$ (Carbontetrachloride), Chloroform are vaporized, and its vaporized and treated water is return edback to the heat exchanger. In the pilot testing the optimum condition of the HWSRS was when the water temperature at the $40^{\circ}C$ and operated with water sparging concurrently, and its TCE removal rate was 90%. The efficiency of the optimized HWSRS has been confirmed through the long-term performance evaluation process.