• Journal of Welding and Joining
• /
• v.24 no.2
• /
• pp.42-47
• /
• 2006

While it is known that the weld toe grinding method may give 3.4 times of fatigue strength improvement, this improvement may significantly vary according to weld bead shapes and loading modes. Although tremendous interest have been given in improving fatigue strength improvement for ship structures, quantitative results are yet in need. In this context, a series of fatigue tests is carried out for a type of test specimen that are typically found in ship structures. Weld burr grinding is carried out using a electric grinder in order to remove surface defects and improve the weld bead profile. The test results are compared with the same type of test specimen without applying the fatigue improvement technique in order to obtain a quantitative measure of the fatigue strength improvement. On the other hand, both hot spot stress and structural stress methods are employed to compare the effectiveness of the two methods in evaluating the fatigue strength improvement of welded structures.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2008.11a
• /
• pp.93-96
• /
• 2008

This research performed strength improvement analysis after evaluating strength characteristics by estimated temperatures to evaluate the real time strength performance of 50 to 80 MPa high performance concrete equipped with heat resistance, and the results are as follows. The lesser W/B and the lesser target slump flow value difference, compression strength was shown to increase, and the more curing temperature becomes, the strength increased accordingly. According to the correlation review result of strength improvement analysis by estimated temperature change performed using logistic analysis model, the compression strength value predicted with logistic curve expression and the compression strength value measured in experiment were shown to have similar correlation, and the strength improvement analysis value by logistic model was shown to be estimated good when W/B is high.

• Proceedings of the KSR Conference
• /
• 1998.11a
• /
• pp.103-110
• /
• 1998

Several soil improvement methods are applied to stabilize soft ground. But their improvement effects are known to be reduced in view of strength under poor conditions such as marine clay. The purpose of this paper is to investigate the strength increase effects of super injection grouting on the marine clay, A series of laboratory tests and chemical analysis tests has been peformed. Through this study, the causes of strength inferiority of treated soil was analyzed and soil improvement effects of grouted soil was presented.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2004.03b
• /
• pp.692-697
• /
• 2004

This study is on the increasement of strength about soft ground improvement material using waste residual(paper fly ash, coke ash, slag) by fire. Through this study the authors have analyzed the strength improvement of mixed soft silty sand with improvement materials. The strength of mixed soils with high mixture ratio and more curing days increased. But CA-30(cokes 60%) make more low strength improvement than others. Therefore the authors find out that paper fly ash+cokes, paper fly ash+slag or cokes+slag improvement material is more effect in improvement of soft silty sand than cokes+cenlent. And Ettringite reaction is free mixed soils with more than two materials.

• Proceedings of the Korean Geotechical Society Conference
• /
• 1999.10a
• /
• pp.227-232
• /
• 1999

In this paper, a laboratory investigation was carried out to estimate the strength improvement of quicklime mixture for the effective use of surplus soils, and the shear strength with curing time was estimated at the content of lime. The effect of strength improvement has been established through the change of lime content with chlorides and sulfates from the samples taken at Samsan region, Ulsan. The test results indicated that the presence of calcium sulphate encouraged the efficiency of lime stabilization, and increased shear strength. Furthermore, it is necessary for inquiring into the relationship between the characteristics of strength and the chemical components.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2000.11a
• /
• pp.55-62
• /
• 2000

In this paper, a laboratory investigation was carried out to estimate the strength improvement of quicklime mixture with fly ash and rice husk ash for the effective use of surplus soils, and the shear strength with curing time was estimated at lime 10 percent with the change of fly ash and rice husk ash content. The effect of strength improvement has been established through the change of fly ash and rice husk ash content from the samples taken at Samsan region, Ulsan. The test results indicated that the presence of lime with fly ash and rice husk ash encouraged the stabilization efficiency of lime with fly ash and rice husk ash, and increased shear strength. Furthermore, it is necessary for inquiring into the relationship between the characteristics of strength and the chemical components.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1993.04a
• /
• pp.79-88
• /
• 1993

The purpose of this study is to provide a firm base for the quality improvement of high strength concrete and the development of ultra high strength concrete as well as enviromental con-servation and utilization of byproducts from industrial processing such as Fly ash and Silica fume. A comprehensive experimental study was performed to investigate the effects on the quality improvement of high strength concrete using mineral admixtures. As results, 400~500kg/$\textrm{cm}^2$ compressive strength and excellent flowability can be obtained if fly ash is replaced with cement in the range of 305. In case of using powder type silica fume, 600~700 kg/$\textrm{cm}^2$ compressive strength is showed and 600~800kg/$\textrm{cm}^2$ compressive strength cam be obtained with liquid type silica fume. But it is necessary to increase dosage of high range water reducer for flowability using powder type silica fume. Especially, higher strength concrete cam be obtained when maximum size of coarse aggregate is lower than 25mm.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2005.03a
• /
• pp.1023-1030
• /
• 2005

This study is an experiment paper about the ground improvement material which using the waste residual(slag and paper fly ash) by fire. we are research to concern according to the soil to mix the ground improvement material at show strength effectiveness. Also, we can expect a long time strength increase effectiveness as reduce the dryness contraction. They are distinguished to the clay of the reclamation ground and silty sand soil. We examined around an uniaxial compress test and scanning electron microscopy. The uniaxial stress increases according to the increase of the mixed ratio of ground improvement material and the water contents have been reduced the strength value. A clay's improvement effectiveness is big but in the silty sand soil to express small effectiveness. A ground improvement material mixing of the quantity to write can not expect the effect of Ettringite.

• Geomechanics and Engineering
• /
• v.8 no.1
• /
• pp.53-66
• /
• 2015

Plastic wastes, particularly polyethylene terephthalate (PET) generated from used bottled water constitute a worldwide environmental issue. Reusing the PET waste for geotechnical applications not only reduces environmental burdens of handling the waste, but also improves inherent engineering properties of soil. This paper investigated factors affecting shear strength improvement of PET-mixed residual soil. Four variables were considered: (i) plastic content; (ii) plastic slenderness ratio; (iii) plastic size; and (iv) soil particle size. A series of unconfined compression tests were performed to determine the optimum configurations for promoting the shear strength improvement. The results showed that the optimum slenderness ratio and PET content for shear strength improvement were 1:3 and 1.5%, respectively. Large PET pieces (i.e., $1.0cm^2$) were favorable for fine-grained residual soil, while small PET pieces (i.e., $0.5cm^2$) were favorable for coarse-grained residual soil. Higher shear strength improvement was obtained for PET-mixed coarse-grained residual soil (148%) than fine-grained residual soils (117%). The orientation of plastic pieces in soil and frictional resistance developed between soil particles and PET surface are two important factors affecting the shear strength performance of PET-mixed soil.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.31 no.3
• /
• pp.47-53
• /
• 1999

The effect of coating of liner components with oxidized starch on the properties of corrugated box was examined . Coating was carried out on liner components of B flute, single-wall corrugated board(SK180/S120/K200) , and corrugated box was made from the treated corrugated board. Box was made in a regular slotted container (RSC) style, and box compression strength was determined in the direction of top-to-bottom compression. The compression strength of box coated on outside liner component showed 15.4% improvement for 1.58g㎡ coating. On the other hand, the strength of box coated on outside liner component showed only 1.45% improvement for 1.41g/㎡ coating and 3.46% improvement for 2.32g/㎡ coating. Coating on inside liner component with oxidized starch at low coating weight more significantly improved box compression strength than coating on outside liner component, and the improvement was marked at the coating weight of 1.5-2.5g/㎡. In estimating top-to-bottom box compression strength, the experimental values were closer to the calculated values from McKee's equation suing edgewise compression strength of the combined board measured by column crush test than those from Kellicutt's equation using compression strength of component paperboards measured by ring crush test.