• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.45 no.4
• /
• pp.94-104
• /
• 2008

In this paper, we propose a new architecture of multiplier-and-accumulator (MAC) for high speed multiplication and accumulation arithmetic. By combining multiplication with accumulation and devising a hybrid type of carry save adder (CSA), the performance was improved. Since the accumulator which has the largest delay in MAC was removed and its function was included into CSA, the overall performance becomes to be elevated. The proposed CSA tree uses 1's complement-based radix-2 modified booth algorithm (MBA) and has the modified array for the sign extension in order to increase the bit density of operands. The CSA propagates the carries by the least significant bits of the partial products and generates the least significant bits in advance for decreasing the number of the input bits of the final adder. Also, the proposed MAC accumulates the intermediate results in the type of sum and carry bits not the output of the final adder for improving the performance by optimizing the efficiency of pipeline scheme. The proposed architecture was synthesized with $250{\mu}m,\;180{\mu}m,\;130{\mu}m$ and 90nm standard CMOS library after designing it. We analyzed the results such as hardware resource, delay, and pipeline which are based on the theoretical and experimental estimation. We used Sakurai's alpha power low for the delay modeling. The proposed MAC has the superior properties to the standard design in many ways and its performance is twice as much than the previous research in the similar clock frequency.

• Journal of the Institute of Electronics Engineers of Korea CI
• /
• v.45 no.3
• /
• pp.175-183
• /
• 2008

In wireless sensor networks with ad hoc networking capability, sensor nodes are battery operated and are usually disposable once deployed. As a result, each sensor node senses and communicates with limited energy and, thus, energy efficiency has been studied as a key design factor which determines lifetime of a wireless sensor network, and it is more improved recently by using so-called cross-layer optimization technique. In this paper, we propose and implement a new energy saving mechanism that reduces energy consumption during data collection by controlling transmission power at sensor nodes and then measure its performance in terms of lifetime improvement for the wireless sensor network platform ZigbeX. When every sensor node transmits sensed data to its clusterhead, it controls its transmission power down to as low level as communication is possible, resulting in energy saving. Each sensor node controls its transmission power based on RSSI(Received Signal Strength Indicator) of the packet received from its clusterhead. In other words, the sensor node can save energy by controlling its transmission power down to an appropriate level that its clusterhead safely receives the packet it transmits. According to the repetitive experiment of the proposed scheme on the ZigbeX platform using the packet analyzer developed by us, it is observed that the network lifetime is prolonged by up to 21.9% by saying energy during the data collection occupying most amount of network traffic.

• Journal of Korean society of Dental Hygiene
• /
• v.4 no.2
• /
• pp.193-207
• /
• 2004

The aims of the study are as following : First, define and clarify the role and function of the dental hygienist. Second, based on thai definition, present an improved dental hygienist curriculum, improving their special competence. This study seeks to present a way for promoting role of dental hygienists as independent specialists, rather than as auxiliaries, contributing to better dental service in the process. The research was pursued by surveying by questionnaire those directly related to dental hygiene. They are 58 professors of dental hygiene, 164 dentists, 253 dental hygienists and 496 dental hygiene students, selected by the method of simple random sampling. Due to the small size of the sample, professors' group was analysed only through frequency and probabilities. For groups with larger samples(dentists, dental hygienists, dental hygiene students), methods of chi square(${\chi}^2$) tests, frequency analysis and one-way ANOVA were used in their analysis. Conclusions of the study are as following : First, role and function of the dental hygienist was defined and clarified. According to the analysis of the survey, main role of the dental hygienists as perceived by 62.9% of dentists was supporting treatments and managing patients and facility. This perception by dentists differs significantly to perception of other groups, which saw main role of dental hygienists as preventive dental treatment and dental hygiene education. Also, only 20.2% of dental hygienists perceived patients and facility management as their main role. This divergence of perception between groups weakens speciality competence of dental hygienists. To strengthen dental hygienists' speciality competence, preventive dental treatment and dental hygiene education must be defined as main role of dental hygienists. Furthermore, role of dental hygienists can be categorized into cooperative and auxiliary role. Second, in order to strengthen speciality competence of dental hygienists, their education must be augmented with curriculum emphasizing cooperative role. Specifically, courses on preventive dental treatment, dental hygiene education and dental X-ray photography must become compulsory, as well as becoming more comprehensive and organized. Also, training in schools and hospitals must be focused on those subjects. In addition, courses concerning auxiliary role must be incorporated into optional courses and more pedagogical courses are needed to widen students' career choices. Third, practical relevance of national dental hygienist certification examination must be heightened. In the survey, all groups gave negative response to questions concerning practical relevance of national dental hygienist certification test. Specifically, contents of the tests must be changed to test participants' competence in the cooperative area. Also, the test itself must be strengthened by adding practical examination to the certification scheme, as well as having more difficult examinations.

• Journal of Korean Society for Atmospheric Environment
• /
• v.30 no.6
• /
• pp.555-568
• /
• 2014

The construction equipment is one of the major sources for hazardous air pollutants in Korea, and the its management has been of great concern recently. The objective of this study was to estimate each contribution of emission of construction equipments according to their production year, electric power consumption and type. To achieve this goal, we developed pollutant emission factors for the machineries manufactured after 2009, which are excluded from the present framework of Korean air pollutants inventory, CAPSS. More than 800 data obtained from emission investigations were utilized for the estimation. Compared with the previous estimation, the scheme used this study was modified to incorporate new emission factors as well as to include the corresponding activity data. Such improvement allow us to gain more detailed emission informations which are better characterized by specifications of construction equipments. The total amount of pollutants emitted from construction equipments in 2011 were estimated as 126.8, 7.0, 58.3, and 17.0 kton for $NO_x$, PM, CO, and VOC, respectively. The estimation results indicate that the increase in the emission of equipments is significantly related to their age and power consumption. The emissions of the older ones manufactured from 1992~1996 were estimated to be the contribution ranged from 23.7% to 26.8%, whereas the newer ones (2009~2011) showed the attributions of 11.3~21.5%. In addition, the results show that the emission of each equipment was increased with the increase in the electric power consumption of engine, probably due to their average output power. Among the nine types of machinery compared, excavators and forklifts were investigated to contribute relatively higher emissions in the level of 39.8~44.0% and 32.0~34.2%, respectively.

• Journal of Korea Water Resources Association
• /
• v.44 no.2
• /
• pp.97-107
• /
• 2011

For the purpose of enhancing usability of NWP (Numerical Weather Prediction), the quantitative precipitation prediction scheme was suggested. In this research, precipitation by leading time was predicted using 3-hour rainfall accumulation by meso-scale numerical weather model and AWS (Automatic Weather Station), precipitation water and relative humidity observed by atmospheric sounding station, probability of rainfall occurrence by leading time in June and July, 2001 and August, 2002. Considering the nonlinear process of ranfall producing mechanism, the ANN (Artificial Neural Network) that is useful in nonlinear fitting between rainfall and the other atmospheric variables. The feedforward multi-layer perceptron was used for neural network structure, and the nonlinear bipolaractivation function was used for neural network training for converting negative rainfall into no rain value. The ANN simulated rainfall was validated by leading time using Nash-Sutcliffe Coefficient of Efficiency (COE) and Coefficient of Correlation (CORR). As a result, the 3 hour rainfall accumulation basis shows that the COE of the areal mean of the Korean peninsula was improved from -0.04 to 0.31 for the 12 hr leading time, -0.04 to 0.38 for the 24 hr leading time, -0.03 to 0.33 for the 36 hr leading time, and -0.05 to 0.27 for the 48 hr leading time.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.13 no.5
• /
• pp.492-499
• /
• 2002

Performance analysis and comparison of the hybrid DS-SFH spread-spectrum (SS) system using coherent MSK and QPSK modulation techniques over Rayleigh fading channel are considered in the presence of MTJ(multi-tone jamming). To analyze the BER performance of the hybrid systems with or without the Rake receiver, signal-to-noise plus interference ratio is derived as a function of the average signal-to-noise ratio, the jammer-to-signal ratio and other system parameters. Numerical results show that the performance difference between the two modulation schemes, MSK and QPSK, is negligible for low JSR, while it becomes significant with the increase of JSR. In multi-path Rayleigh fading channel without Rake receiver, the performances of the two modulation schemes are slightly improved as the DS spreading gain is increased when the total SS bandwidth is fixed. In particular, there is an optimum DS spreading gain for large JSR, in which a minimum BER is achieved, while only DS spreading gives the best performance for small JSR. For hybrid systems with Rake receiver, it is shown that the hybrid system of the MSK modulation scheme provides better anti-jamming performance and larger performance improvement with the increase of multi-path resolution capability of Rake receiver than that of QPSK modulation for all conditions.

• KIPS Transactions on Computer and Communication Systems
• /
• v.2 no.6
• /
• pp.265-278
• /
• 2013

With the recent advancements in various wireless communication technologies, the importance of mobile multicasting is coming to the fore, in an effort to use network resources more efficiently. In the past, when various mobile IP-based multicast techniques were proposed, the focus was put on the costs needed for network delivery for providing multicast services, as well as on minimizing the multicast handover delay. For techniques using MIPv6 (Mobile IPv6), a host-based mobility management protocol, however, it is fundamentally difficult to resolve the problems of handover delay and tunnel convergence. To resolve these problems, a network-based mobility management protocol called PMIPv6 (Proxy Mobile IPv6) was standardized. Although performance is improved in PMIPv6 over MIPv6, it still suffers from the problems of handover delay and tunnel convergence. In this paper, to overcome these limitations, a technique called LFH (Low-cost and Fast Handoff) is proposed for fast and low-cost mobility management with multicasting support in PMIPv6 networks. To reduce the interactions between the complex multicast routing protocol and the multicast messages, a simplified proxy method called MLD (Multicast Listener Discovery) is implemented and modified. Furthermore, a TCR (Tunnel Combination and Reconstruction) algorithm was used in the multicast handover procedure within the LMA (Local Mobility Anchor) domain, as well as in the multicast handover procedure between domains, in order to overcome the problem of tunnel convergence. As a result, it was found that LFH has reduced multicast delay compared to other types of multicast techniques, and that it requires lower costs as well.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.24 no.4
• /
• pp.11-20
• /
• 2016

Depletion of natural resources and reduction of greenhouse gas emissions are an important issue which we have to solve. The recycling of waste has emerged as a global concern. In Korea, the development of cost-effective treatment and recycling technologies also need to be improved. In this study, we compared and analyzed the cost per unit of treatment and recycling of organic waste, and presented an effective recycling scheme. We investigated the current status of treatment and costs for six types of organic wastes from 80 workplaces, including organic wastewater treatment sludge, processed organic sludge, and plant residues. In addition, environmental costs for greenhouse gas reduction were calculated. It's an economic way that organic waste is composted and used as cement additives. In particular, the economic analysis was done by realistic results of the survey target companies. In conclusion, in order for reliable processing and recycling of organic wastes, wastewater treatment sludge and sewage sludge need to be classified based on hazard characteristics. Finally, technical difficulties need to be further resolved such as odors, leachate, and debris on recycling organic wastes.

• Earthquakes and Structures
• /
• v.12 no.6
• /
• pp.603-617
• /
• 2017

This paper presents investigation into the behavior of beam-column joints, with the joint region concrete being replaced by steel fiber reinforced concrete (SFRC) and by ultra-high performance concrete (UHPC). A total of ten beam-column joint specimens (BCJ) were tested experimentally to failure under monotonic and cyclic loading, with the beam section being subjected to flexural loading and the column to combined flexural and axial loading. The joint region essentially transferred shear and axial stresses as received from the column. Steel fiber reinforced concrete (SFRC) and ultra-high performance concrete (UHPC) were used as an innovative construction and/or strengthening scheme for some of the BCJ specimens. The reinforced concrete specimens were reinforced with longitudinal steel rebar, 18 mm, and some specimens were reinforced with an additional two ties in the joint region. The results showed that using SFRC and UHPC as a replacement concrete for the BCJ improved the joint shear strength and the load carrying capacity of the hybrid specimens. The mode of failure was also converted from a non-desirable joint shear failure to a preferred beam flexural failure. The effect of the ties in the SFRC and UHPC joint regions could not be observed due to the beam flexural failure. Several models were used in estimating the joint shear strength for different BCJ specimens. The results showed that the existing models yielded wide-ranging values. A new concept to take into account the influence of column axial load on the shear strength of beam-column joints is also presented, which demonstrates that the recommended values for concrete tensile strength for determination of joint shear strength need to be amended for joints subject to moderate to high axial loads. Furthermore, finite element model (FEM) simulation to predict the behaviour of the hybrid BCJ specimens was also carried out in an ABAQUS environment. The result of the FEM modelling showed good agreement with experimental results.

• Journal of Korean Library and Information Science Society
• /
• v.20
• /
• pp.351-381
• /
• 1993

The purpose of this study is to analyze the various processes and patterns to build or synthesize class numbers in the 800 class of the Dewey Decimal Classification, Edition 20(1989). The results of the analysis are as follows: 1. The 800(Literature and rhetoric) class in the DDC system is the main class added analytico-synthetic principle positively to an enumerative scheme. 2. The facets to be a n.0, pplied in literature are language literary form literary period ; kind, scope, or medium ; notation 08(collection) or 09(criticism) literary feature, subject, author, etc. 3. In the 800 class, there are the five tables of precedence for literary forms aspects ; specific kinds of persons ; literary, period in relation to the aspects for works treating more than one literary form subforms, aspects and literary periods in the works treating a specific literary form. 4. The basic number synthesis of literary works proceeds through the various facets in the following sequence, as far as necessary for the item : base no. + literary form + literary time or period + kind, scope, or medium + notation 08 or 09 + subform + additional notation from T3C and other tables. 5. In view of the multiplicity of facets, their synthesis formulas take the following order : (1) Works about the literature : base no.(schedule) + language(T6) or form(T3B) (2) Works by or about individual author : base no.(schedule) + form (T3A) + period(schedule) + subform(T3A) (3) Works by or about more than one author, not restricted by language facet : base no.(schedule) + period(T1) ; base no.(schedule) + kind, scope, medium(T3B), or feature(T3C), or person(T5). (4) Works by or about more than one author, restricted by language facet : base no.(schedule) + form (T3B) + period(schedule) + subform(T3B) + notation 08 or 09(T3B) ; base no.(schedule) + notation 08 or 09(T3B) + 9(T3C) + area notation(T2) : base no.(schedule) + form (T3B) + notation 008 or 009(T3B) : base no.(schedule) + form (T3B) + kind, scope, medium(T3B) + notation 08 or 09(T3B) + period(schedule). (5) Affiliated literatures for which period numbers are not us base no.(schedule) + form (T3A or T3B), or notation 08 or 09(T3B) : base no.(schedule) + kind, scope, medium(T3B), feature(T3C), or person(T5) 6. The problems in the number building of the 800 class are the complexity and difficulty of number synthesis, the intrinsic weakness of from distinction and the inconvenience of retrieval inherent in the form class. In order to solve these problems, therefore, the citation orders and methods of DDC should be improved and synthesis patterns simplified from the point of view of its applicability and its usefulness in the "literature class".