• The Journal of Korean Academy of Prosthodontics
• /
• v.39 no.1
• /
• pp.84-95
• /
• 2001

Titanium is widely used in dentistry for its low density, high strength, fatigue resistance, corrosion resistance, and biocompatibility. But it has a tendency of surface damage under circumstance of friction and impact for its low hardness of the surface. Coating is one of methods fir increasing surface hardness. Its effect is to improve surface physical characteristics without change of titanium. Diamond-like carbon and titanium nitride are known for its high hardness of the surface. So that this study was aimed at the wear test and the cytotoxicity test of the commercially pure titanium and Ti-6Al-4V alloy which were deposited by diamond-like carbon film or titanium nitride film to acertain improvement of the surface hardness and the biocompatibility. A disk (25mm diameter, 2mm thickness) was made of commercially pure titanium and Ti-6Al-4V alloy and these substrates were deposited by diamond-like carbon film or titanium nitride film. Diamond-like carbon film was deposited by the method of radiofrequency plasma assisted chemical vapor deposition and titanium nitride film was deposited by the method of reactive arc ion plating. Then these substrates were tested about wear characteristics by the pin-on-disk type wear tester in which ruby ball was used as a wear causer under the load of 32N, The fracture cycles were measured by rotating the substrates until their films were fractured. The wear volume was measured after 150 cycles and 3,000 cycles using surface profiler. The cytotoxicity test was peformed by the method of the MTT assay. The results were as follows : 1. In the results of the wear volume test, commercially pure titanium and titanium alloy which were coated by diamond-like carbon film or titanium nitride aim had higher resistance against wear than the substrates which were not coated by any films (P<0.05). 2. In the results of the fracture cycle test and the wear volume test, diamond-like carbon film had higher resistance against wear than titanium nitride film (P<0.05). 3. In both coatings of diamond-like carbon aim and titanium nitride film, Ti-6Al-4V alloy had higher resistance against wear than commercially pure titanium (P<0.05) 4. In the results of the cytotoxicity test, diamond-like carbon film and titanium nitride film had little cytotoxicity as like commercially pure titanium or Ti-6Al-4V alloy (P>0.05).

• Journal of the Korea Concrete Institute
• /
• v.28 no.6
• /
• pp.673-683
• /
• 2016

In recent years, frequent terror or military attack by explosion, impact, fire accidents have occurred. Particularly, World Trade Center collapse and US Department of Defense Pentagon attack on Sept. 11 of 2001. Also, nuclear power plant incident on Mar. 11 of 2011. These attacks and incidents were raised public concerns and anxiety of potential terrorist attacks on major infrastructures and structures. Therefore, the extreme loading researches were performed of prestressed concrete (PSC) member, which widely used for nuclear containment vessel and gas tank. In this paper, to evaluate the blast resistance capacity and its protective performance of bi-directional unbonded prestressed concrete member, blast tests were carried out on $1,400{\times}1,000{\times}300mm$ for reinforced concrete (RC), prestressed concrete without rebar (PSC), prestressed concrete with rebar (PSRC) specimens. The applied blast load was generated by the detonation of 55 lbs ANFO explosive charge at 1.0 m standoff distance. The data acquisitions not only included blast waves of incident pressure, reflected pressure, and impulse, but also included displacement, acceleration, and strains at steel, concrete, PS tendon. The results can be used as basic research references for related research areas, which include protective design and blast simulation under blast loading.

• The KIPS Transactions:PartC
• /
• v.14C no.5
• /
• pp.417-424
• /
• 2007

Mesh networks using WLAN technology have been paid attention as a key wireless access technology. However, many technical issues still exist for its successful deployment. One of those issues is the routing problem that addresses the path setup through a WLAN mesh network for the data exchanges between a station and a wired network. Since the characteristics of a WLAN mesh network can be very dynamic, the use of single routing protocol would not fit for all environments whether it is reactive or proactive. Therefore, it is required to develop an adaptive routing protocol that modifies itself according to the changes in the network parameters. As a logical first step for the development, an analytical model considering all the dynamic features of a WLAN mesh network is required to evaluate the performance of a reactive and a proactive routing scheme. In this paper, we propose an analytical model that makes us scrutinize the impact of the network and station parameters on the performance of each routing protocol. Our model includes the size of a mesh network, the density of stations, mobility of stations. and the duration of network topology change. We applied our model to the AODV that is a representative reactive routing protocol and DSDV that is a representative proactive routing protocol to analyze the tradeoff between AODV and DSDV in dynamic network environments. Our model is expected to help developing an adaptive routing protocol for a WLAN mesh network.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.23 no.1
• /
• pp.97-104
• /
• 2015

This study is a part of the high pressure injection system development on the Turbo GDI engine in order to reduce smoke emission in case of using the low volatile(high DI) fuel which is used as normal gasoline fuel in the US market. Firstly, theoretical approach was done regarding gasoline fuel property, performance, definition of particle matters and its creation as well as problems of the high DI fuel. In this experimental study, 2L Turbo GDI engine was selected and optimized system parameter was inspected by changing fuel, fuel injection mode (single/multiple), fuel pressure, distance between injector tip and combustion chamber, start of injection, intake valve timing in engine dyno at all engine speed range with full load. In case of normal gasoline fuel, opacity was contained within 2% in all conditions. On the other hands, in case of low volatile fuel (high DI fuel), it was confirmed that the opacity was rapidly increased above 5,000 rpm at 14.5 ~ 20 MPa of fuel pressure and there were almost no differences on the opacity(smoke) between 17 MPa and 20 MPa fuel pressure. According to the SOI retard, smoke decrease tendency was observed but intake valve close timing change has almost no impact on the smoke level in this area. Consequently, smoke decrease was observed and 16% at 6000rpm respectively with injector washer ring installed. By removing injector washer to make injector tip closer to the combustion chamber, smoke decrease was observed by 46% at 5,500 rpm, 42% at 6,000 rpm. It is assumed that the fuel injection interaction with cylinder head, piston head, intake and exhaust valve is reduced so that impingement is reduced in local area.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.5
• /
• pp.1-9
• /
• 2016

Railroad bridges account for 25% of the entire high-speed rail network. Railway bridges are subject to gradual structural degradation or fatigue accumulation due to consistent and repeating excitation by fast moving trains. Wireless sensing technology has opened up a new avenue for bridge health monitoring owing to its low-cost, high fidelity, and multiple sensing capability. On the other hand, measuring the transient response during train passage is quite challenging that the current wireless sensor system cannot be applied due to the intrinsic time delay of the sensor network. Therefore, this paper presents a framework for monitoring such transient responses with wireless sensing systems using 1) real-time excessive vibration monitoring through ultra-low-power MEMS accelerometers, and 2) post-event time synchronization scheme. The ultra-low power accelerometer continuously monitors the vibration and trigger network when excessive vibrations are detected. The entire network of wireless smart sensors starts sensing through triggering and the post-event time synchronization is conducted to compensate for the time error on the measured responses. The results of this study highlight the potential of detecting the impact load and triggering the entire network, as well as the effectiveness of the post-event time synchronized scheme for compensating for the time error. A numerical and experimental study was carried out to validate the proposed sensing hardware and time synchronization method.

• Journal of radiological science and technology
• /
• v.28 no.1
• /
• pp.45-53
• /
• 2005

This study is aimed at analyzing the relationship between personal factors of radiological technologists and their job stressors. For this aim, a survey was conducted by means of 890 questionnaires from the middle of July to the end of August 2003 to the subjects of radiological technologists who are working for 44 general hospitals in 16 cities and provinces across the country. The results of the survey could be summed up as follows: 1. The biggest stressor that affects a radiological technologist personally under the working situation turned out to be position, job satisfaction and physical symptom(p<0.001), while job satisfaction and physical symptom also played an important role in personal relationship(p<0.001). 2. In terms of job conflicts, colleagues, immediate seniors, job satisfaction and physical symptoms appeared to exercise great impact(p<0.001), As for job autonomy, age, position and job satisfaction were known to be heavily influential(p<0.001). 3. With regard to job load, job satisfaction and behavioral symptom turned out to have great influence while, in job stability, position and job satisfaction seemed to be immensely influential(p<0.001). The present study has a limit in that it covers only radiological technologists who are working at the 3rd reference hospitals but excludes those who are working at the first and second reference hospitals. The findings, however, are surely believed to be able to serve as basic data to improve the medical service quality as they will help reduce the stressors of and enhance mental and physical health for radiological technologists who play important roles as teammates with expertise in the medical field. These outcomes could also be referred to in future studies in this area.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.7 no.3
• /
• pp.243-254
• /
• 2019

In this study, problems of the waterproofing methods in which water leakage occurs in the upper slab of the underground parking lot of apartment houses and the requirements considering the characteristics of the upper slab, and selected the appropriate performance(proposal) for the composite polyurea process are reviewed. As a result of the study, it is necessary to review performance such as responsiveness to upper slab of the multi-unit underground parking lot that is comprised of (1) crack and behavior responsiveness, (2) surface integrity, (3) vertical watertight stability, (4) pressure layer construction, (5) impact and pressure response and (6) vehicle moving load. As a result of evaluating 5 items corresponding to the requirements for the soft and hard complex polyurea, all of them were found to meet the conditions, and each materials were improved by compounding the materials that had problems when applying a single-ply method, thereby clarifying the advantages and disadvantages of the material property. However, in order to apply to the actual site, additional evaluation on site applicability such as mock-up evaluation should be conducted, and subsequent studies on the applicability of the market through review of economic feasibility and maintenance is required.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.23 no.6
• /
• pp.699-709
• /
• 2017

We measured the grain size, total organic carbon (TOC), total nitrogen (TN), and heavy metals (As, Cd, Cr, Cu, Fe, Hg, Mn, Pb, and Zn) in order to understand the spatial distribution and pollution level of organic matter and metals in surface sediment around Goseong Bay, a shellfish farming area, Korea. The surface sediments were composed of finer sediments such as mud and clay. The concentration of TOC, TN, and heavy metals were much higher in the innermost bay than in the mouth and outside of bay. The spatial distribution of organic matter and heavy metals and C/N ratio (5-10) in sediment showed that the organic matter and heavy metals in sediment of the study region were significantly influenced by oceanic origin organic matter and anthropogenic sources, respectively. Based on the results of four assessment techniques (sediment quality guideline, geoaccumulation index, pollution load index, ecological risk index), the sediments around the Goseong Bay were a little polluted for heavy metals and the high metal concentrations in the northern region of bay could adverse impact on benthic organisms in sediment. Thus, the systematic management plan for the improvement of water and sediment environment and the concentrated monitoring of pollutants for sustainable aquaculture and seafood safety around Goseong Bay are necessary in the future.

• Journal of Wetlands Research
• /
• v.21 no.1
• /
• pp.9-15
• /
• 2019

The Daegi-cheon watershed is located in the upper part of the Han River, which has the representative highland vegetable growing complexes. This watershed has a large impact on the water quality and aquatic ecosystem in the upstream of the Han River by discharging a large amount of turbid water during rainfall season. For proposing an efficient turbid water management and policy, the analysis of the characteristics of flow rate and SS and its causes needs to be carried out preferentially. In this study, the relationship between flow rate and SS concentration was analyzed in the Daegi-cheon watershed, and in turn the turbidity characteristics were analyzed. As a result of the study, in the normal flood flow condition, it was shown that SS concentration changed arbitrarily due to various environmental factors. On the other hand, the SS concentration was considerably high in the very high flow condition. Based on the field survey, this could be the reason why the effects of the steep valley and slope collapse according to the very high flow rate as well as the source in the agricultural fields were greatly contributed. Therefore, it is necessary to develop a structural best management practice that can stabilize the steep slope and reduce river bed loss along with the typical source managements plans.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.8
• /
• pp.8-14
• /
• 2019

Bird-strike is one of the most important design factors for safety in the aviation industry. Bird-strikes have been the cause of significant damage to aircraft and rotorcraft structures and the loss of life. This study used DYTRAN software to simulate the transient response of an Euler-Lagrangian composite helicopter blade that has been impacted by a bird. The Arbitrary Lagrangian Eulerian (ALE) method and a suitable equation of state were applied to model the bird. ALE was applied to the bird-strike analysis due to the large difference between the properties of the blade and bird. The debris of the bird was assumed to be a fluid and applied as Euler elements after the collision. Through the analysis of bird impacts, the leading-edge of the rotor blade (50.8 mm) was used to identify a positive margin of 1.18 based on the TSAI-FILL criteria. The results are assessed to be sufficiently reliable and may be evaluated to replace tests with various analysis conditions. The structural stability of the rotor blade could be assessed by applying various load conditions and different modeling methods in the future.