• 대한치과재료학회지
• /
• 제43권4호
• /
• pp.317-322
• /
• 2016

The effect of ice-quenching after degassing on the hardness change during simulated porcelain firing in a metal-ceramic Pd-Au-Ag alloy was investigated by means of hardness test, field emission scanning electron microscopic observations, and X-ray diffraction analysis. The hardness decreased by ice-quenching after degassing, which was induced by the homogenization of the ice-quenched specimen. The decreased hardness by ice-quenching after degassing was recovered from the 1st opaque stage which was the first stage of the remaining firing process for bonding porcelain. The microstructural change showed that the increase in hardness during the remaining firing process was caused by precipitation. The ice-quenching after degassing did not affect the hardness change during the subsequent porcelain firing process.

• 대한치과재료학회지
• /
• 제44권3호
• /
• pp.197-206
• /
• 2017

본 연구에서는 포세린 소성과정 동안 금속하부구조물의 경도가 하강하는 문제점을 개선하기 위해 모의소성 시 산화처리 단계에서 서냉(bench cooling) 대신 급랭(ice-quenching)으로 합금을 냉각시킴으로써 나머지 소성단계 동안 경화효과를 얻을 수 있을 것으로 예측하고, 이를 확인하기 위해 실험을 진행하였다. 본 연구에서는 Pd-Ag-Sn-Au계 금속-세라믹용 합금을 사용하여 실험을 진행하여 다음과 같은 결과를 얻었다. 산화처리 후 stage 0으로 냉각한 시편과 산화처리 후 급랭한 시편을 glaze까지 모의소성한 결과, 두 시편 모두 소성 첫 단계에서 경도가 상승한 후 지속적으로 경도가 하강하였으나, 산화처리 후 급랭한 시편의 최종 경도가 더 높게 나타났다. 소성 첫 단계에서 일어난 경도의 상승은 면심입방구조의 Pd-Ag-rich 기지에서 면심정방구조의 Pd3(Sn, Ga, In)상의 석출로 인해 기지와 석출물간의 계면에 생성된 격자변형에 기인하였다. 모의소성과정에 따른 경도의 하강은 석출물이 조대화됨에 따라 석출물과 기지사이의 계면의 면적이 감소되어 격자 뒤틀림이 해소된 것에 기인하였다.

• 한국조명전기설비학회지:조명전기설비
• /
• 제6권5호
• /
• pp.27-37
• /
• 1992

We studied the dielectric and dynamic mechanical losses according to the quenching condition in low density polyethylene being used to power cables. According to severe quenching condition, characteristics of the temperature in internal friction los peak have decreased the magnitude of loss peak as amorphous region lengthen. From now on, the frequency dependent characteristics of dielectric loss have investigated at room temperature, and the dielectric loss peak due to interface polarization, between crystal and amorphous region, occurs about 30[Hz], and that, the peak due to orientation polarization in correspondence to the loss peak in internal friction has observed at about 3 [MHz]. As quenching velocity increased, the effect on quenching condition about the dielectric loss has decreased the magnitude of the loss peak. Thus, estimation has been carried out on the activation energies nd the degree of crystallinity by means of X-ray diffraction are obtained as follows: room quenching : 26.4 [kal/mole] and 54.73 [%], ice quenching : 25.6 [kcal/mole] and 48.47 [%], liquid nitrogen quenching specimens : 22.56 [kcal/mole] and 40.95 [%].

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1983년도 하계학술회의강연.논문초록집
• /
• pp.223-224
• /
• 1983

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1996년도 추계학술대회 논문집
• /
• pp.164-168
• /
• 1996

The relation between crystallinity and thermal history in low density polyethylene thin films and their effect on electric conduction phenomena and dielectric breakdown was studied. The low density polythylene thin films obtained by the solution growth method heat-treated at 140[$^{\circ}C$] for 2 h and subsequently cooling to various ways. The degree of crystallinity was estimated by the X-ray diffraction measurement for the specimen of slowly cooling, ICE quenching and liquid nitrogen quenching. The result shows that the crystallinity decreases become faster as the cooling speed increased, and that conduction phenomenon is governed by the space charge limited current in high field. It was found that the dielectric breakdown field increases with an increase in cooling speed and test number in self-healing breakdown method.

• 한국정밀공학회지
• /
• 제28권10호
• /
• pp.1210-1216
• /
• 2011

The purpose of this study is to establish the analysis method for prediction of temperature during cryogenic heat treatment. Experimental cryogenic heat treatment is conducted to observe the phenomena such as boiling of fluid, ice layer on the material surface and to measure the temperature distribution of Al6061 tube. The CFD analysis considering the observed phenomena in the experiment is performed to predict the temperature distribution and convection heat transfer coefficient at each stage of cryogenic heat treatment, in which the boiling of fluid is considered as the multi-phase condition of vapour and liquid. The formation of ice layer on the tube surface is also modeled between material and fluid. The predicted results are in good agreement with the experimental ones. From the results, it is shown that the analysis method can predict the temperature distribution and convection heat transfer coefficient during cryogenic heat treatment.

• 한국재료학회지
• /
• 제30권5호
• /
• pp.231-238
• /
• 2020

The composition of martensite transformation in NiAl alloy is determined using pure nickel and aluminum powder by vacuum hot press powder metallurgy, which is a composition of martensitic transformation, and the characteristics of martensitic transformation and microstructure of sintered NiAl alloys are investigated. The produced sintered alloys are presintered and hot pressed in vacuum; after homogenizing heat treatment at 1,273 K for 86.4 ks, they are water-cooled to produce NiAl sintered alloys having relative density of 99 % or more. As a result of observations of the microstructure of the sintered NiAl alloy specimens quenched in ice water after homogenization treatment at 1,273 K, it is found that specimens of all compositions consisted of two phases and voids. In addition, it is found that martensite transformation did not occur because surface fluctuation shapes did not appear inside the crystal grains with quenching at 1,273 K. As a result of examining the relationship between the density and composition after martensitic transformation of the sintered alloys, the density after transformation is found to have increased by about 1 % compared to before the transformation. As a result of examining the relationship between the hardness (Hv) at room temperature and the composition of the matrix phase and the martensite phase, the hardness of the martensite phase is found to be smaller than that of the matrix phase. As a result of examining the relationship between the temperature at which the shape recovery is completed by heating and the composition, the shape recovery temperature is found to decrease almost linearly as the Al concentration increases, and the gradient is about -160 K/at% Al. After quenching the sintered NiAl alloys of the 37 at%Al into martensite, specimens fractured by three-point bending at room temperature are observed by SEM and, as a result, some grain boundary fractures are observed on the fracture surface, and mainly intergranular cleavage fractures.

• 한국재료학회지
• /
• 제8권11호
• /
• pp.1031-1037
• /
• 1998

Zircaloy-4와 Zr-2.5Nb 합금의 부식에 미치는 냉각속도와 소둔온도의영향을 조사하기 위해서 여러 가지 방법으로 열처리된 시편에 대해서 autoclave 부식시험을 실시하였다. 냉각속도의 영향을 조사하기 위해서 시편을 $1050^{\circ}C$에서 30분 가열 후 염빙수냉, 수냉, 유냉, 공냉, 노냉의 방법에 의해 열처리하였으며, 소둔온도의 영향을 조사하기 위해서 $\alpha$온도, $\alpha$+$\beta$온도, $\beta$온도구역에서 열처리하였다. $500^{\circ}C$부식시험 결과, Zircaloy-4합금에서는 nodule형 부식이 발생되는 반면에 Zr-2.5Nb 합금에서는 nodule형 부식이 발생되지 않았다. Zirfcaloy-4 합금에서는 nodule형 부식이 발생되는 반면에 Zr-2.5Nb 합금에서는 nodule형 부식이 발생되지 않았다. Zircaloy-4합금은 냉각속도가 빠를수록 내식성이 증가하는 반면에 Zr-2.5Nb합금은 냉각속도가 빠를수록 내식성이 감소하는 경향을 보였다. 또한 소둔온도가 증가할수록 Zr-2.5Nb 합금의 내식성은 감소하는 결과를 보였다. Zircaloy-4의 내식성은 Fe, Cr 원소의 기지내 분포와 석출물의 분포에 의해 지배를 받으며 Zr-2.5Nb 합금의 내식성은 기지조직내의 Nb 농도와 $\beta_{-Nb}$상에 의해 지배를 받는 것으로 사료된다.

• 대한치과기공학회지
• /
• 제23권1호
• /
• pp.65-73
• /
• 2001

The purpose of this study was to investigate the microstucture and hardness, corrosion of pure Ti alloy, which is widely used as partial denture frame work these days, depending on the cooling method, followed by casting. The first group was bench cooling at room temperature($18^{\circ}C$), the second group was slowly cooled in the furnace from $700^{\circ}C$ to room temperature, and third. rapidly cooled in $0^{\circ}C$ water. The microstructure of each specimen observed by means of photomicrograph taken by electron microscope, in add to the physical characteristics of each specimen were obtained using the rockwell Hardnest Number. the characteristics of corrosion. The results were obtained as follows: 1. From Potentiodynamic plot. we conclude furnace-cooled specimen had the best stabiltity of passive film and that air-cooled specimen showed similar characteristics. The density of electric current of quenched specimen was the highest, which formed kind of unstable passive film. 2. Specimen cooled at room temperature (air cooling) had the highest value of hardness of 81.26HRB, specimen cooled at ice-water, $0^{\circ}C$, had the value of 78.42HRB, and specimen furnace-cooled at $700^{\circ}C$ had lowest value of 77.1HRB. 3. Quenching treated micro-structure formed martensite structure by and large. In case of air cooling, we could see $\alpha$-structure widmanstatten formed overall. In furnace cooling, widmanstatten structure and various shape $\alpha$-structures forming colony with direction were detected.

• Journal of Korean Dental Science
• /
• 제10권1호
• /
• pp.10-21
• /
• 2017

Purpose: The purpose of this study was to investigate the electrochemical characteristics of nanotubular Ti-25Nb-xZr ternary alloys for dental implant materials. Materials and Methods: Ti-25Nb-xZr alloys with different Zr contents (0, 3, 7, and 15 wt.%) were manufactured using commercially pure titanium (CP-Ti), niobium (Nb), and zirconium (Zr) (99.95 wt.% purity). The alloys were prepared by arc melting in argon (Ar) atmosphere. The Ti-25Nb-xZr alloys were homogenized in Ar atmosphere at $1,000^{\circ}C$ for 12 hours followed by quenching into ice water. The microstructure of the Ti-25Nb-xZr alloys was examined by a field emission scanning electron microscope. The phases in the alloys were identified by an X-ray diffractometer. The chemical composition of the nanotube-formed surfaces was determined by energy-dispersive X-ray spectroscopy. Self-organized $TiO_2$ was prepared by electrochemical oxidation of the samples in a $1.0M\;H_3PO_4+0.8wt.%$ NaF electrolyte. The anodization potential was 30 V and time was 1 hour by DC supplier. Surface wettability was evaluated for both the metallographically polished and nanotube-formed surfaces using a contact-angle goniometer. The corrosion properties of the specimens were investigated using a 0.9 wt.% aqueous solution of NaCl at $36^{\circ}C{\pm}5^{\circ}C$ using a potentiodynamic polarization test. Result: Needle-like structure of Ti-25Nb-xZr alloys was transform to equiaxed structure as Zr content increased. Nanotube formed on Ti-25Nb-xZr alloys show two sizes of nanotube structure. The diameters of the large tubes decreased and small tubes increased as Zr content increased. The lower contact angles for nanotube formed Ti-25NbxZr alloys surfaces showed compare to non-nanotube formed surface. The corrosion resistance of alloy increased as Zr content increased, and nanotube formed surface showed longer the passive regions compared to non-treatment surface. Conclusion: It is confirmed that corrosion resistance of alloy increased as Zr content increased, and nanotube formed surface has longer passive region compared to without treatment surface.