• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.49 no.4
• /
• pp.232-238
• /
• 2000

PZT thin films(3500 ) have been prepared onto $Pt/Ti/SiO_2/Si$ substrates with a RF magnetron sputtering system using PB1.05(Zr0.52,Ti0.48)O3 ceramic target. We used two-step annealing techniques. As the RTA times and temperatures were increased, crystallization of PZT thin films were enhanced. The ferroelectric characteristics of PZT capacitors fabricated at $700^{\circ}C$ for 60 seconds were like these remanent polarization were $12.1 \muC/cm^2$, coercive field were 110 kV/cm, leakage current density were $4.1\times10-7 A/cm^2,\; \varepsilonr=442,$ and remanent polarization were decreased by 22% after 1010 cycles, respectively.

• Proceedings of the KIEE Conference
• /
• 2008.04c
• /
• pp.86-88
• /
• 2008

The rotational loss is one of the most important problems for the practical use of the high power Flywheel Energy Storage System (FESS). This rotational loss is divided as the mechanical loss by windage and bearing and iron loss by hysteresis loop and eddy current in the part of the magnetic field. So, In this paper, a double-sided PMSM/G without the iron loss is designed by analytical method of the magnetic field and estimation of the back-EMF constant represented as the design parameter. This design model consists of the double-sided PM rotor with Halbach magnetized any and coreless 3-phase winding stator. The results show that the double-sided PMSM/G without iron loss can be applicable to the high power FESS.

• Proceedings of the KIEE Conference
• /
• 1996.07a
• /
• pp.56-58
• /
• 1996

The Preisach model needs a density function to simulate the hysteresis phenomena. To obtain this function, many experimental data obtained from the first order transition curves are required to get accurate density function. However, it is difficult to perform this procedure, especially for the hard magnetic materials. In this paper, we compare the density function obtained from the experimental data with that computed from the mathematical function like the Gaussian function, and propose a simple technique to get mathematical equation of the density function or Everett function which is obtained from the initial curve, major and minor loop.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.23 no.6
• /
• pp.616-621
• /
• 2003

There are various Non-Destructive Evaluation (NDE) techniques used for measurement of residual stresses in material, such as magnetic methods, X-ray diffraction, Ultrasonic velocity measurement etc. The capabilities, applications and limitations of these techniques for evaluation of cold work/plastic deformation were studied and compared. Mild steel plates were subjected to different degree of cold deformation and were analyzed by Magneto-mechanical Acoustic Emission (MAE), Barkhausen Noise (BN) and magnetic properties (hysteresis loop parameters analysis). Further, these specimens were analyzed by X-ray diffraction and ultrasonic velocity measurements. The microhardness measurement and microstructure studies of these cold worked plates were also carried out. The results of all these studies and comparison of different techniques are discussed in this paper.

• Journal of the Korean Ceramic Society
• /
• v.29 no.11
• /
• pp.870-876
• /
• 1992

Lead lanthanum zirconate titanate (PLZT, 6/65/35) powders, crack-free and dense thin films have been prepared by polymeric sol-gel process. Pyrolysis of the gel, crystallization and optical transmittance behavior of the PLZT thin film onto sapphire substrate have been studied. Esterification occurs during synthesis of PLZT complexation. Crystalline Pb phase was transiently formed near 450$^{\circ}C$. Content of perovskite phase in the films were increased with increasing thickness of film, but the kinetics of formation of perovskite phase in films was slower than that of powders. Transmittance of the films was decreased with increasing the temperature of heat treatment. Ferroelectric hysteresis loop measurements indicated increments of remanent polarization and coercive field for plenty more of perovskite phase.

• Proceedings of the KIEE Conference
• /
• 1992.07b
• /
• pp.1055-1059
• /
• 1992

Instantaneous Voltage Control of inverter for uninterruptible power supply(UPS) is presented. In order to improve the transient response, the authors propose a control scheme based on a double regulation loop with sinusoidal hysteresis band. And also, using 8097 single chip microprocessor, software synchronization and static switch control scheme is impremented with minimal hard ware structure.

• Structural Engineering and Mechanics
• /
• v.52 no.6
• /
• pp.1177-1191
• /
• 2014

Reinforced concrete (RC) shear walls are one of the most commonly used lateral-load resisting systems in high-rise buildings. RC Parallel redundancy walls studied herein consist of two parts nested to each other. These two parts have different mechanical behaviors and energy dissipation mechanisms. In this paper, experimental studies of four 1/2-scale specimens representing this concept, which are subjected to in-plane cyclic loading, are presented and test results are discussed. Two specimens consist of a wall frame with barbell-shaped walls embedded in it, and the other two consist of a wall frame and braced walls nested each other. The research mainly focuses on the failure mechanism, strength, hysteresis loop, energy dissipation capacity and stiffness of these walls. Results show that the RC parallel redundancy wall is an efficient lateral load resisting component that acts as a "dual" system with good ductility and energy dissipation capacity. One main part absorbs a greater degree of the energy exerted by an earthquake and fails first, whereas the other part can still behave as an independent role in bearing loads after earthquakes.

• Journal of Magnetics
• /
• v.1 no.2
• /
• pp.90-93
• /
• 1996

For the design of high efficiency electric machines, analysis of higher harmonic frequency components of the magnetic induction is necessary. We have measured ac magnetic properties of non-oriented silicon steel under harmonic frequencies ranging from $3^rd$ (180 Hz) to $9^th$(540 Hz) and harmonic amplitude components from 10% to 50% of the total amplitude ($B_max$=1.5T). From the experiment, it is found that, if the magnetic induction waveform has above $9^th$ harmonic frequency components of the magnetic induction, the core losses only depended on the harmonic amplitude component, but if harmonic frequency becomes lower than 9th harmonic frequency, the core losses depend on the phase angle and the harmonic amplitude, and phase angle should be considered in the design of electric machine.

• Journal of Korean Association for Spatial Structures
• /
• v.20 no.1
• /
• pp.79-86
• /
• 2020

The performance enhancement of various damping systems from natural hazards has become an highly important issue in engineering field. In this paper, ENTA hysteretic dampers were tested under cyclic loadings to evaluate their performance in terms of ductility and energy dissipation. The test results showed that the hysteretic dampers are effective damping systems to enhance the buildings performance for remodeling and retrofit of buildings. Also, the hysteretic dampers were modeled in FEM(Finite Element Method) structural analysis program. As comparing the computer modeling and the experiment, this study model reflects the nonlinear behavior of steel and derives the hysteresis loop.

• Journal of the Korean Ceramic Society
• /
• v.24 no.6
• /
• pp.586-592
• /
• 1987

The role of the strain energy and phase stability in the diffuse phase transition have been investigated in the highly disordered solid solution, (Pb1-xBax)(Zr0.4Ti0.6)O3 (0.2 x 0.4). X-ray diffraction analysis indicates that tetragonality (c/a) decreases with the increasing Ba content. Also as the Ba content increases, phase transition becomes more diffuse and at the same time dielectric relaxation as a function of measured frequencies in the 1KHz-10MHz range occurs very pronouncedly. In the Ba content range, 0.2 x 0.35, hysteresis loops are routinely observed and the loop is observed to narrow shape as the Ba content increases but becomes very slim at 40mol% Ba content. Moreover thermal analysis shows that there is no abrupt change in the thermal expansion coefficient below the apparent transition temperature at which dielectric constant becomes maximum. From the above results, it has been concluded that creation of the strain energy due to the distorthion that occurred during the phase transition suppresses diffuse phase transition.