• Journal of the Korean Society of Propulsion Engineers
• /
• v.26 no.2
• /
• pp.20-27
• /
• 2022

Hypergolic propellant ignited spontaneously when fuel and oxidizer contact without ignition system. Due to this characteristic, the risk of accidents is high when new propellants are evaluated. Prevention of accidents is very important because the damage can be large when the accident occur. In this work, we proposed non-ignition evaluation method which can replace conventional ignition evaluation method by using microreactor. The reactor was fabricated by MEMS. The heat of reaction as according to fuel and NaBH₄ was estimated. At the condition of highest heat of reaction ignition was observed by drop test.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.26 no.6
• /
• pp.74-85
• /
• 2022

Since the late 1990s, the demand for developing green or reduced-toxic storable propellants has been rising to replace the existing toxic propellants. Most of the research activities are focusing on development of new hypergolic fuels and either white fuming nitric acid or hydrogen peroxide is utilized as an oxidizer. The newly-developed hypergolic fuels are classified as three types, catalytic fuel, reactive fuel, and ionic fuel. In the present study, recent R&D trend of ionic liquid propellants is described and the main results in the previous studies are analyzed.

• Journal of the Korean Electrochemical Society
• /
• v.3 no.4
• /
• pp.200-203
• /
• 2000

Boron doped conducting diamond thin films were grown on Si substrate by microwave plasma chemical vapor deposition from a gaseous feed of hydrogen, acetone/methanol and solid boron. The doping level of boron was ca. $10^2ppm\;(B/C)$. The Si substrate was tilted ca. $10^{\circ}$ to make Si substrate, which have different height and temperature. Experimental results showed that different crystalline of diamond thin films were made by different temperature of Si substrate. There appeared $3\~4$ steps of different crystalline morphology of diamond. To characterize the boron-doped diamond thin film, Raman spectroscopy was used for identification of crystallinity. To survey surface morphology, microscope was used. Grain size was changed gradually by different temperature due to different height. The Raman spectrum of film exhibited a sharp peak at $1334cm^{-1}$, which is characteristic of crystalline diamond. The lower position of diamond film position, the more non-diamond component peak appeared near $1550 cm^{-1}$.

• Journal of the Korean Vacuum Society
• /
• v.6 no.4
• /
• pp.348-353
• /
• 1997

Hydrogenated amorphous carbon(a-C:H) films were deposited on p-type Si(100) by DC saddle-field plasma enhanced CVD to investigate the effect of substrate bias on optical properties and structural changes. They were deposited using pure methane gas at a wide range of substrate bias at room temperature and 90 mtorr. The substrate bias voltage ($V_s$) was employed from $V_s=0 V$ to $V_s=400 V$. The information of optical properties was investigated by photoluminescence and transmitance. Chemical bondings of a-C:H have been explored from FT-IR and Raman spectroscopy. The thickness and relative hydrogen content of the films were measured by Rutherford backscattering spectroscopy (RBS) and elastic recoil detection (ERD) technigue. The growth rate of a-C:H film was decreased with the increase of $V_s$, but the hydrogen content of the film was increased with the increase of $V_s$. The a-C:H films deposited at the lowest $V_s$ contain the smallest amount of hydrogen with most of C-H bonds in the of $CH_2$ configuration, whereas the films produced at higher $V_s$ reveal dominant the $CH_3$ bonding structure. The emission of white photoluminescence from the films were observed even with naked eyes at room temperature and the PL intensity of the film has the maximum value at $V_s$=200 V. With $V_s$ lower than 200 V, the PL intensity of the film increased with V, but for V, higher than 200 V, the PL intensity decreased with the increase of $V_s$. The peak energy of the PL spectra slightly shifted to the higher energy with the increase of $V_s$. The optical bandgap of the film, determined by optical transmittance, was increased from 1.5 eV at $V_s$=0V to 2.3 eV at $V_s$=400 V. But there were no obvious relations between the PL peak and the optical gap which were measured by Tauc process.

• Parasites, Hosts and Diseases
• /
• v.54 no.1
• /
• pp.21-29
• /
• 2016

The sodium hydrogen exchanger 1 (NHE1), which functions in maintaining the ratio of $Na^+$ and $H^+$ ions, is widely distributed in cell plasma membranes. It plays a prominent role in pH balancing, cell proliferation, differentiation, adhesion, and migration. However, its exact subcellular location and biological functions in Toxoplasma gondii are largely unclear. In this study, we cloned the C-terminal sequence of T. gondii NHE1 (TgNHE1) incorporating the C-terminal peptide of NHE1 (C-NHE1) into the pGEX4T-1 expression plasmid. The peptide sequence was predicted to have good antigenicity based on the information obtained from an immune epitope database. After induction of heterologous gene expression with isopropyl-b-D-thiogalactoside, the recombinant C-NHE1 protein successfully expressed in a soluble form was purified by glutathione sepharose beads as an immunogen for production of a rabbit polyclonal antiserum. The specificity of this antiserum was confirmed by western blotting and immunofluorescence. The antiserum could reduce T. gondii invasion into host cells, indicated by the decreased TgNHE1 expression in T. gondii parasites that were pre-incubated with antiserum in the process of cell entry. Furthermore, the antiserum reduced the virulence of T. gondii parasites to host cells in vitro, possibly by blocking the release of $Ca^{2+}$. In this regard, this antiserum has potential to be a valuable tool for further studies of TgNHE1.

• Journal of Pharmaceutical Investigation
• /
• v.29 no.1
• /
• pp.29-36
• /
• 1999

Aceclofenac is an non-steroidal antiinflammatory drug which has been used in the treatment of rheumatoidal rthritis and osteo-arthritis. In order to decrease the gastric ulcerogenic effects and contol the plasma level of aceclofenac, we have developed the transdermal delivery system of aceclofenac plaster, which were formulated employing matrix polymers of acrylates and penetration-enhancers such as $Lauroglycol^{\circledR}$, $Transcutol^{\circledR}$, oleic acid and linoleic acid. Using Franz diffusion cells mounted with a rat skin, transdermal penetration characteristics of the formulations were evaluated by the HPLC assay of aceclofenac and diclofenac, an active metabolite, in the receptor compartment of pH 7.2 phosphate buffered solution. Skin penetration was increased when the content of aceclofenac increased, showing the flux $(J,\;{\mu}g/cm^2/hr)$ of 0.37 and 2.50 for 2% and 6.75% of the content, respectively. The flux$(J,\;{\mu}g/cm^2/hr)$ from plasters made of $Durotak^{\circledR}$ 87-2074, $Durotak^{\circledR}$ 87-2510 and $Durotak^{\circledR}$ 87-2097 were 2.50, 2.77 and 4.39, respectively. $Durotak^{\circledR}$ 87-2074 showed the lowest penetration due to the carboxylic acid group in the polymer, which might form a strong hydrogen bonding with a secondary amine of aceclofenac. Although both $Durotak^{\circledR}$ 87-2510 and $Durotak^{\circledR}$ 87-2097 are amine-resistant adhesives, $Durotak^{\circledR}$ 872510 showed lower penetration than $Durotak^{\circledR}$ 87-2097 because of the hydroxyl group in $Durotak^{\circledR}$ 87-2510, which might form a weak hydrogen bonding with aceclofenac. These results reveal that the functional group in acrylic polymers would greatly affect the release of aceclofenac from the matrix, which is the rate-limiting step in the penetration of aceclofenac through rat skins. The penetration of aceclofenac from plasters using different penetration-enhancers increased in the following order: Transcutol < linoleic acid < oleic acid. And the flux from the plasters containing oleic acid as a penetrationenhancer was 2.22 times greater than that of creams, which suggest that a newly deveolped aceclofenac plaster could be used in the treatment of rheumatoidal arthritis and osteo-arthritis as an advanced transdermal delivery system.

• Asian-Australasian Journal of Animal Sciences
• /
• v.28 no.1
• /
• pp.111-119
• /
• 2015

A growth trial was conducted to determine the optimal incorporation level of dietary magnesium hydrogen phosphate (MHP, $MgHPO_4$), which was manufactured from swine manure and phosphorus (P), required by juvenile far eastern catfish (Silurus asotus). Graded MHP of 0.5%, 1.0%, 1.5%, and 2.0%, and 2.0% monocalcium phosphate (MCP) each was added to the basal diet (control) in lieu of cellulose to become the range of available P (AP) from 0.4% to 0.8% of which diets were designated as control, MHP0.5, MHP1.0, MHP1.5, MHP2.0, and MCP, respectively. Control diet contained fish meal (20%), soybean meal (40%), wheat flour (27%), corn gluten meal (5%), fish oil (2%) and soy oil (2%) as main ingredients. Following a 24 h fasting, 540 fish with a mean body weight of 11.8 g were randomly allotted to 6 groups in triplicate, whereby 18 tanks ($0.4{\times}0.6{\times}0.36cm$, water volume of 66 L) were prepared. The feeding experiment lasted for 8 weeks. Fish group fed the control diet showed the lowest weight gain (WG) and feed efficiency (FE) among treatments. The WG was, however, not significantly different (p>0.05) from that of fish group fed MHP0.5. Fish group fed MHP2.0 showed the highest WG and FE of which values were not significantly different from those of fish groups fed diets MHP1.0 and MHP1.5 as well as MCP (p>0.05) except fish groups fed control and MHP0.5. Aspartate aminotransferase was significantly decreased with an increase in available P, while alanine aminotransferase did not show a significant difference among treatment. The highest inorganic P in plasma was observed in fish fed MHP2.0. From the present results, a second-order regression analysis revealed that the optimal dietary MHP level and the AP requirement were found to be 1.62% and 0.7%, respectively.

• Proceedings of the KWS Conference
• /
• 2009.11a
• /
• pp.30-30
• /
• 2009

GTA 용접에서 용입, 용접부의 크기와 형상이 형성되는 아크 물리학적 현상을 이해함에 있어서 에너지 분포특성은 매우 중요한 인자이다. GTA 용접에서 아크 길이의 변화와 사용된 실드 가스 종류에 따라 음극인 텅스텐 전극 팁의 아크 루트 직경에 큰 변화를 주며, 양극인 모재 쪽의 에너지 분포에 영향을 미치며 된다. 기존의 연구자들은 저전류나 중전류 영역의 GTA 용접에서 텅스텐 전극의 선단각과 용입 형태와 의 관계를 plasma 기류 등에 의해 고찰하거나, 최대 아크압력에 미치는 전극형상의 영향에 대하여 연구하였다. 용접부에 작용하는 아크 압력의 분포는 결국 운동 에너지의 분포이다. 기존의 연구자들에 비하여 보다 간편한 실험을 통하여 양극 모재위의 아크 압력에 의한 에너지 분포특성을 규명하는 연구가 필요하다. 본 연구의 목적은 GTA 용접의 용접전류 100A~200A 영역에서 아크 길이 변화와 Ar 가스에 $H_2$ 혼합에 따른 측정된 아크 압력으로부터 기존연구자들의 아크 물리학적 결과들을 활용하여 양극 모재 위에 작용하는 전류밀도 분포를 유도하는 것이다. GTA 용접에서 아크 길이의 변화와 Ar 가스에 $H_2$ 혼합은 아크 압력분포에 큰 영향을 미치며, 이에 따라 에너지 분포특성에 많은 영향을 미친다. 아크 길이가 증가함에 따라 Ar가스와 $H_2$ 혼합가스의 에너지 분포는 감소하였고, Ar가스에 $H_2$ 혼합에 의해 아크 에너지가 증가하여 용입형상에 큰 영향을 미칠 것으로 판단된다. 이에 대한 연구는 향후 GTA 용접 응용분야 확대 적용될 것이며, 아크 물리학 연구에 기초적이고 아주 중요한 과학적인 자료가 될 것으로 판단된다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.421-422
• /
• 2011

The first part is about development of a liquid target for a neutron source, which is designed to overcome many of the limitations of traditional beam-target neutron generators by utilizing a liquid target neutron source. One of the most critical aspects of the beam-target neutron generator is the target integrity under the beam exposure. A liquid target can be a good solution to overcome damage to the target such as target erosion and depletion of hydrogen isotopes in the active layer, especially for the one operating at high neutron fluxes with no need for water cooling. There is no inherent target lifetime for the liquid target neutron generator when used with continuous refreshment of the target surface exposed to the energetic beam. In this work, liquid target containing hydrogen has been developed and tested in vacuum environment. Potentially, liquid targets could allow a point neutron source whose spatial extension is on the order of 1 to $10{\mu}m$. And the second is about the vacuum ultraviolet (VUV) spectrometer which is designed as a five-channel spectral system for ITER main plasma measurement. To develop and verify the design, a two-channel prototype system was fabricated with No. 3 (14.4 nm~31.8 nm) and No. 4 (29.0 nm~60.0 nm) among the five channels. For test of the prototype system, a hollow cathode lamp is used as a light source. The system is composed of a collimating mirror to collect the light from source to slit, and two holographic diffraction gratings with toroidal geometry to diffract and also to collimate the light from the common slit to detectors. The two gratings are positioned at different optical distances and heights as designed. To study the appropriate detector for ITER VUV system, two different electronic detectors of the back-illuminated charge coupled device and the micro-channel plate electron multiplier were installed and the performance has been investigated and compared in the same experimental conditions. The overall system performance was verified by measuring the spectrums.

• Journal of the Korean Vacuum Society
• /
• v.7 no.4
• /
• pp.403-409
• /
• 1998

In this study, the effects of multi-dipole type of magnets on the characteristics of the inductively coupled plasmas and $SiO_2$ etch properties were investigated. As the magnets, 4 pairs of permanent magnets were used and, to etch $SiO_2, C_2F_6, CHF_3, C_4F_8, H_2$, and their combinations were used. The characteristics of the magnetized inductively coupled plasmas were investigated using a Langmuir probe and an optical emission spectrometer, and $SiO_2$ etch rates and the etch selectivity over photoresist were measured using a stylus profilometer. The use of multi-dipole magnets increased the uniformity of the ion density over the substrate location even though no significant increase of ion density was observed with the magnets. The use of the magnets also increased the electron temperature and radical densities while reducing the plasma potential. When $SiO_2$ was etched using the fluorocarbon gases, the significant increase of $SiO_2$ etch rates and also the increase of etch uniformity over the substrate were obtained using the magnets. In case of gas combinations with hydrogen, $C_4F_8/H_2$ showed the highest etch rates and etch selectivities over photoresist among the gas combinations with hydrogen used in the experiment. By optimizing process parameters at 1000 Watts of inductive power with the magnets, the highest $SiO_2$ etch rate of 8000 $\AA$/min could be obtained for 50% $C_4F_8/50% H_2$.