• 제어로봇시스템학회:학술대회논문집
• /
• 2003.10a
• /
• pp.548-552
• /
• 2003

In the braking system, the friction force is the most important factor of the design. For long time, many researchers have been strived for getting the exact friction coefficients. But the friction coefficients are affected by the road condition and changed by lots of parameters, such as normal force and characteristics between two contacted materials, temperature, etc. For the development of ABS of the aircraft, HILS(Hardware-In-the-Loop-Simulation) test and dynamometer test was carried out. For the calculation of the friction coefficients, the wheel moments were measured using the load cell mounted on the housing of the wheel. The test conditions were dry and greasy, as the 0.7 and 0.4 in friction coefficient, respectively. In this paper, the test results of the friction coefficients were represented and the improvement method was suggested.

• Journal of the Korean Society for Precision Engineering
• /
• v.14 no.8
• /
• pp.146-154
• /
• 1997

Solenoid-folw control type ABS is used with a 'dump and reapply' pressure control arrangement instead of using 2/2 (normal open/close) solenoid valves in convensional systems(sol. -sol. control type), a flow control valve is used which replaces the (no) inlet valve. The flow control valve controls fluid flow providing a nearly constant reapply rate( .theta. ) after the dump plase of ABS operation. In this study, to investigate a characteristics of brake pressure by PWM control, test rig was consisted of ABS hydraulic modulator, digital controller, pneumatic power supply and brake master cylinder. For comparison with experi- mental results, system modelling and computer simulation were performed. As a result, experiment results showed fairly agreement with the simulation. Also, it is shown that the pressure gradient (tan .theta. ) is affected by pressure, frequency, duty ratio and expressed with an exponential funtion.

• 제어로봇시스템학회:학술대회논문집
• /
• 2001.10a
• /
• pp.35.3-35
• /
• 2001

Developed is an optical auto-inspection system to detect some microscopic defects on the Inside surface of the hydraulic automobile brakes at the production line. A small cylindrical detection module with a solid laser source at its center has two rings of optical fibers to separately collect light reflected and scattered from the defects on the surface. The cylindrical brake part rotates with respect to the detection module that will move parallel to the rotational axis of the cylinder. Thus, the optical module can scan the whole inside surface area. The automatic detection of the defects is to compare the intensity distributions ...

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.13 no.2
• /
• pp.69-74
• /
• 2004

In general the surge pressure generated in hydraulic systems causes noise, vibration and odd effect to the system. To reduce the surge pressure, high frequency PWM control of 20KHz was attempted. To estimate the braking noise caused by surge, a vehicle equipped with on-board ABS hydraulic modulator has been experimented with respect to the various breaking condition. Thorough this experiments, it was found that breaking noise has been reduced using high frequency PWM control method compare with low frequency method. To evaluate high frequency control m practice, including verification of general functionality, EMI tests was experimented. Its was found that it is necessary to have the solution to electromagnetic interference(EMI) generated by switching elements.

• Journal of the Korean Society for Precision Engineering
• /
• v.21 no.6
• /
• pp.84-93
• /
• 2004

This study carries out the performance improvement and simplification of hydraulic modulator that plays an important role in vehicle stability control systems. The mathematical models for each component of a modulator, such as pump, wheel cylinder, check and solenoid valve, accumulator, damper are derived in detail. All the mathematical models are combined to form a modulator system and implemented through a computer program, which can be controlled by a user friendly GUI. To verity the simulation, comparison between simulation and experiments has been made. After the verification of the validity of the simulation, the effects of the design parameters of the modulator on the wheel cylinder pressure is investigated. The results show that the modulator without MPA has advantage in early time pressure rise rate, and it can be simplified.

• 제어로봇시스템학회:학술대회논문집
• /
• 2005.06a
• /
• pp.1983-1989
• /
• 2005

Industrial robots are powerful, extremely accurate multi-jointed systems, but they are heavy and highly rigid because of their mechanical structure and motorization. Therefore, sharing the robot working space with its environment is problematic. A novel pneumatic artificial muscle actuator (PAM actuator) has been regarded during the recent decades as an interesting alternative to hydraulic and electric actuators. Its main advantages are high strength and high power/weight ratio, low cost, compactness, ease of maintenance, cleanliness, readily available and cheap power source, inherent safety and mobility assistance to humans performing tasks. The PAM is undoubtedly the most promising artificial muscle for the actuation of new types of industrial robots such as Rubber Actuator and PAM manipulators. However, some limitations still exist, such as the air compressibility and the lack of damping ability of the actuator bring the dynamic delay of the pressure response and cause the oscillatory motion. In addition, the nonlinearities in the PAM manipulator still limit the controllability. Therefore, it is not easy to realize motion with high accuracy and high speed and with respect to various external inertia loads in order to realize a human-friendly therapy robot To overcome these problems a novel controller, which harmonizes a phase plane switching control method with conventional PID controller and the adaptabilities of neural network, is newly proposed. In order to realize satisfactory control performance a variable damper - Magneto-Rheological Brake (MRB) is equipped to the joint of the manipulator. Superb mixture of conventional PID controller and a phase plane switching control using neural network brings us a novel controller. This proposed controller is appropriate for a kind of plants with nonlinearity uncertainties and disturbances. The experiments were carried out in practical PAM manipulator and the effectiveness of the proposed control algorithm was demonstrated through experiments, which had proved that the stability of the manipulator can be improved greatly in a high gain control by using MRB with phase plane switching control using neural network and without regard for the changes of external inertia loads.

• 제어로봇시스템학회:학술대회논문집
• /
• 2001.10a
• /
• pp.170.3-170
• /
• 2001

Antilock brake system(ABS) prevent the wheels of road vehicle from locking up and skidding so that the braking force is from static friction instead of kinetic friction. Therefore ABS helps drivers maintain steering control during breaking situation particularly at an emergency stopping situation. So when trying to stop the road vehicle it is best to have the most friction possible for faster deceleration ABS keep the wheels turning which means there is more friction between the tires of vehicles and the road surface. Because of this advantage, ABS are now a commonly installed feature for passenger's safety in road vehicles. In this study, hydraulic system of ABS of vehicle is composed of 3port-2position solenoid valve. In order to minimize ...

• 제어로봇시스템학회:학술대회논문집
• /
• 2001.10a
• /
• pp.166.1-166
• /
• 2001

Anti-lock Braking System(ABS) is a device which prevents the wheels form locked up under emergency braking of a vehicle. So it helps the vehicle to maintain the steerability and shortens the braking distance by maintaining optimal frictional force during braking since the tire road slip is controlled in acceptable range. Recently, ABS is accepted as a standard equipment in vehicles, especially in commercial vehicles(bus and trucks). Commercial vehicles don´t use hydraulic lines but use pneumatic lines for braking system mostly. In this paper, ECU(Electronic Control Unit) for the anti-lock braking system of a commercial vehicle which is equipped with a full-air brake system and its control algorithms are presented. In this algorithm wheel speed acceleration flags and wheel slip flags are defined ...

• 제어로봇시스템학회:학술대회논문집
• /
• 2001.10a
• /
• pp.174.4-174
• /
• 2001

Vehicle stability control system can enhance the vehicle stability and handling in the emergency situations through the control of traction and braking forces at the individual wheels. To achieve the desired performance, the wheel slip controller manages the hydraulic braking system to generate the desired braking force at each wheel. In this study, we propose the wheel slip controller for the generation of the braking forces based on multiple sliding mode control theory with the pulse width modulation. The proposed controller follows to the slip ratio and the brake pressure the desired ones so that the vehicle stability controller can Intervene braking force at each wheel. We show the validity and usefulness of the proposed controller through computer simulations.

• Journal of Institute of Control, Robotics and Systems
• /
• v.16 no.8
• /
• pp.735-743
• /
• 2010

A new Fuzzy sliding mode controller is proposed to improve the cornering performance of the four wheel hybrid vehicles. The Fuzzy sliding mode control is applied for the control of rear motor and EHB (Electro-Hydraulic Brake) to improve the cornering performance. The modeling of the automobile is simplified that each of the two wheels is modeled as two degrees of freedom object and the friction coefficient between the wheel and the ground is assumed to be constant. The output of the Fuzzy sliding mode algorithm is the direct yaw moment for the rear wheels, which compensates for the slip angle. Through the simulations using ADAMS and MATLAB Simulink, the cornering performance of the proposed algorithm is compared to the conventional PID to show the superiority of the proposed algorithm. In the simulation experiments, the J-Turn and single lane change are used for each of the Fuzzy sliding mode algorithm and PID controller with the optimal gains which are tuned empirically.