• Journal of the Korean Society for information Management
• /
• v.19 no.2
• /
• pp.69-92
• /
• 2002

A hybrid information service may include local and/or remote distributed services, both and electronic. Also, a hybrid information service can be described as one which an appropriate range of heterogeneous information services is presented to the user in a consistent and integrated way via a single interface. The purpose of this study is to suggest high-level requirements and logical architecture to design hybrid library. High-level requirements analysis for hybrid library need to contain baseline requirements, basic system requirements, searching, location, requesting, delivery and payment. A logical architecture need to consider logical architecture for hybrid library management system including user access points, hybrid library management system and hybrid library components and 5 layered architecture including presenter, coordinator, mediator, communicator and provider to achieve local simplicity while still supporting complex functionality of hybrid library.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.22 no.4
• /
• pp.253-259
• /
• 2018

Structure behaviors resulting from an earthquake are experimentally simulated mainly through a shaking table test. As for large-scale structures, however, size effects over a miniature may make it difficult to assess actual behaviors properly. To address this problem, research on the hybrid simulation is being conducted actively. This method is to implement numerical analysis on framework members that affect the general behavior of the structure dominantly through an actual scale experiment and on the rest parts by applying the substructuring technique. However, existing studies on hybrid simulation focus mainly on Slow experimental methods, which are disadvantageous in that it is unable to assess behaviors close to the actual level if material properties change depending on the speed or the influence of inertial force is significant. The present study aims to establish a Real-time hybrid simulation system capable of excitation based on the actual time history and to verify its performance and applicability. The hybrid simulation system built up in this study utilizes the ATS Compensator system, CR integrator, etc. in order to make the target displacement the same with the measured displacement on the basis of MATLAB/Simulink. The target structure was a 2-span bridge and an RC pier to support it was produced as an experimental model in order for the shaking table test and Slow and Real-time hybrid simulations. Behaviors that result from the earthquake of El Centro were examined, and the results were analyzed comparatively. In comparison with the results of the shaking table test, the Real-time hybrid simulation produced more similar maximum displacement and vibration behaviors than the Slow hybrid simulation. Hence, it is thought that the Real-time hybrid simulation proposed in this study can be utilized usefully in seismic capacity assessment of structural systems such as RC pier that are highly non-linear and time-dependent.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.18 no.12
• /
• pp.1133-1138
• /
• 2005

In this study, we have prepared, as the pluse power source, a commercially supplied Li-ion battery with a capacity of 700 mAh and AC resistivity of 60 md at 1 kHz and nonaqeous asymmetric hybrid capacitor composed of an activated carbon cathode and MCMB anode, and have examined the electrochemical characteristics of hybrid capacitor and the pulse performances of parallel connected hybrid capacitor/Li-ion battery source. The nonaqueous asymmetric hybrid capacitors constituted with each stack number of pairs composed of the cathode, the porous separator and the anode electrode were housed in Al-laminated film cell. The 10 stacked hybrid capacitor, which was charged and discharged at a constant current at 0.25 $mA/cm^2$ between 3 and 4.3 V, has exhibited the capacitance of 108F and the lowest equivalent series resistance was 32 $m{\Omega}$ at 1 kHz. On the other hand, the enhanced run time of Li-ion battery assisted by the hybrid capacitor was obtained with increasing of current density and pulse width in Pulse mode. The best improvement, $84\;\%$ for hybrid capacitor/Li-ion battery was obtained in the condition of a 7C-rate pulse (100 msec)/0.5C-rate standby/$10\;\%$ duty cycle.

• Fisheries and Aquatic Sciences
• /
• v.18 no.1
• /
• pp.99-107
• /
• 2015

A natural hybrid of a probable intergeneric mating between the striped shiner Pungtungia herzi and the stone morocco Pseudorasbora parva (Cypriniformes: Cyprinidae) was captured in the Geumho River, a tributary of the Nakdong River basin in Korea. Morphological characters and DNA sequences were analyzed to verify its hybrid state and identify the parentage of its parent species. The hybrid exhibited a phenotypic intermediacy between the two parent species in the number of vertebrae and the mouth shape. Out of 1,488 base pair (bp) positions of the nuclear recombination activating gene 1 gene (rag1), which has a biparental mode of inheritance, 41-bp substitutions were detected between the two parent species, whereas an electropherogram of the hybrid displayed polymorphic double peaks at all of the base positions, along with one additional one, strongly indicating its hybrid state. Meanwhile, sequence comparison of the mitochondrial cytochrome b gene (mt-cyb) (1,140 bp), which has a maternal mode of inheritance, showed only 5-22-bp differences (97.6-99.5% identities) between the hybrid and Pu. herzi, but as many as 158-168-bp differences (85.2-86.1% identities) between the hybrid and Ps. parva, clearly indicating Pu. herzi as the maternal species. Thus, combined analyses of independent data sets (i.e., morphology and nuclear and mitochondrial DNA sequences) offered convincing evidence for the hybrid state of a naturally occurring hybrid resulting from intergeneric mating between a female Pu. herzi and a male Ps. parva.

• Ocean Systems Engineering
• /
• v.3 no.1
• /
• pp.35-53
• /
• 2013

In this study, a hybrid floating structure with cylinder was introduced to reduce the hydrodynamic motions of the pontoon type. The hybrid floating structure is composed of cylinders and semi-opened side sections to penetrate the wave impact energy. In order to exactly investigate the hydrodynamic motions and structural behavior of the hybrid floating structure under the wave loadings, integrated analysis of hydrodynamic and structural behavior were carried out on the hybrid floating structure. Firstly, the hydrodynamic analyses were performed on the hybrid and pontoon models. Then, the wave-induced hydrodynamic pressures resulting from hydrodynamic analysis were directly mapped to the structural analysis model. And, finally, the structural analyses were carried out on the hybrid and pontoon models. As a result of this study, it was learned that the hybrid model of this study was showed to have more favorable hydrodynamic motions than the pontoon model. The surge motion was indicated even smaller motion at all over wave periods from 4.0 to 10.0 sec, and the heave and pitch motions indicated smaller motions beyond its wave period of 6.5 sec. However, the hybrid model was shown more unfavorable structural behavior than the pontoon model. High concentrated stress occurred at the bottom slab of the bow and stern part where the cylinder wall was connected to the bottom slab. Also, the hybrid model behaved with the elastic body motion due to weak stiffness of floating body and caused a large stress variation at the pure slab section between the cylinder walls. Hence, in order to overcome these problems, some alternatives which could be easily obtained from the simple modification of structural details were proposed.

• Computers and Concrete
• /
• v.19 no.4
• /
• pp.395-404
• /
• 2017

In this paper, the mechanical property of CFRP, BFRP, GFRP and their hybrid FRP was experimentally studied. The elastic modulus and tensile strength of CFRP, BFRP, GFRP and their hybrid FRP were tested. The experimental results showed that the elastic modulus of hybrid FRP agreed well with the theoretical rule of mixture, which means the property of hybrid composites are linear with the volumes of the corresponding components while the tensile strength did not. The bearing capacity, peak strain, stress-strain relationship of circular concrete columns confined by CFRP, BFRP, GFRP and hybrid FRP subjected to axial compression were recorded. And the confinement effect of hybrid FRP on concrete columns was analyzed. The test results showed that the bearing capacity and ductility of concrete columns were efficiently improved through hybrid FRP confinement. A strength model and a stress-strain relationship model of hybrid FRP confined concrete columns were proposed. The proposed stress-strain model was shown to be capable of providing accurate prediction of the axial compressive strength of hybrid FRP confined concrete compared with Teng et al. (2002) model, Karbhari and Gao (1997) model and Miyachi et al. (1999) model. The modified stress-strain model was also suitable for single FRP confinement cases and it was so concise in form and didn't have piecewise fitting, which would be easy for use in structural design.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.597-598
• /
• 2005

Recently, the performance of portable electric equipment can often improved by a Li-ion battery assisted by a supercapacitor. A supercapacitor can provide high power density as well as a low resistance in the hybrid system. In this study, we have prepared, as the pluse power souce, a commercially supplied Li-ion battery with a capacity of 700mAh and AC resistivity of $60m\Omega$ at 1kHz and nonaqeous asymmetric hybrid capacitor composed of an activated carbon cathode and MCMB anode, and have examined the electrochemical characteristics of hybrid capacitor and the pulse performances of parallel connected battery/hybrid capacitor source. The nonaqueous asymmetric hybrid capacitor, the stacks of 10 pairs of the cathode, the porous separator and the anode electrode were housed in Al-laminated film cell. The hybrid capacitor, which was charged and discharged at a constant current at $0.25mA/cm^2$ between 3 and 4.3V, has exhibited the capacitance of 100F. And the equivalent series resistance was $32m\Omega$ at 1kHz. By combining a Li-ion battery and a hybrid capacitor, the pulse performance of battery can be improved 23% in run time under a pulse discharge of 7C-rate.

• International journal of advanced smart convergence
• /
• v.12 no.4
• /
• pp.361-369
• /
• 2023

Achieving realistic visual quality while maintaining optimal real-time rendering performance is a major challenge in evolving computer graphics and interactive 3D applications. Normal mapping, as a core technology in 3D, has matured through continuous optimization and iteration. Hybrid normal mapping as a new mapping model has also made significant progress and has been applied in the 3D asset production pipeline. This study comprehensively explores the hybrid normal techniques, analyzing Linear Blending, Overlay Blending, Whiteout Blending, UDN Blending, and Reoriented Normal Mapping, and focuses on how the various hybrid normal techniques can be used to achieve rendering performance and visual fidelity. performance and visual fidelity. Under the consideration of computational efficiency, visual coherence, and adaptability in different 3D production scenes, we design comparative experiments to explore the optimal solutions of the hybrid normal techniques by analyzing and researching the code, the performance of different hybrid normal mapping in the engine, and analyzing and comparing the data. The purpose of the research and summary of the hybrid normal technology is to find out the most suitable choice for the mainstream workflow based on the objective reality. Provide an understanding of the hybrid normal mapping technique, so that practitioners can choose how to apply different hybrid normal techniques to the corresponding projects. The purpose of our research and summary of mixed normal technology is to find the most suitable choice for mainstream workflows based on objective reality. We summarized the hybrid normal mapping technology and experimentally obtained the advantages and disadvantages of different technologies, so that practitioners can choose to apply different hybrid normal mapping technologies to corresponding projects in a reasonable manner.

• International Journal of Automotive Technology
• /
• v.7 no.4
• /
• pp.423-439
• /
• 2006

This paper proposes a hybrid analytic method for the prediction of vibrational and acoustic responses of reverberant system in the medium-to-high frequency ranges by using the PFA(Power Flow Analysis) algorithm and SEA(Statistical Energy Analysis) coupling concepts. The main part of this method is the application of the coupling loss factor(CLF) of SEA to the boundary condition of PFA in reverberant system. The hybrid method developed shows much more promising results than the conventional SEA and equivalent results to the classical PFA for various damping loss factors in a wide range of frequencies. Additionally, this paper presents applied results of hybrid power flow finite element method(hybrid PFFEM) by formulating the new joint element matrix with CLF to analyze the vibrational responses of built-up structures. Finally, the analytic results of coupled plate structures and an automobile-shaped structure using hybrid PFFEM were predicted successively.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2009.10a
• /
• pp.791-791
• /
• 2009

Hybrid air-foil magnetic bearing combines two oil free bearing technologies to take advantage of the strengths of each bearing with minimizing each other weaknesses. This paper presents bending mode vibration control of a flexible shaft supported by the hybrid air-foil magnetic bearing. An experiment set-up of a flexible shaft supported by the hybrid air-foil magnetic bearing is built. In order to verify the effectiveness of the hybrid bearing, unbalance responses of the flexible shaft supported by three different bearings: air-foil, magnetic and hybrid bearings are compared. Effect of load sharing between air-foil and magnetic bearings are investigated through changing control gain and offset displacements of magnetic bearing.