• Journal of Ship and Ocean Technology
• /
• v.7 no.3
• /
• pp.56-65
• /
• 2003

The hull monitoring systems of container ships with four long-base gages give enough information for identifying the hull girder loads such as bending and torsional moments. But such a load-identification for container ships has not been known. In this paper, a load-identification method is suggested in terms of a linear matrix equation that the measured strain vector equals to the multiplication of the transformation matrix and the desired strain component vector. The equation is proved to be mathematically complete by the property of positive-definite determinant of the transformation matrix. The method is applied to a hull stress monitoring system for 8100TED container ship during sea trial, and the estimated external loads illustrate reasonable results in comparison with the pre-estimated results. This moment decomposition concept has also been tested in real operation conditions. The typical phenomena over the Suez Canal illustrated very suitable results comparing with the physical understandings. Henceforth, one can effectively use the proposed concept to monitor the hull girder loads such as bending and torsional moments.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2004.04a
• /
• pp.77-82
• /
• 2004

This study presents reliability assessment of merchant ships with focus on hull girder ultimate limit state, taking into account the time-dependent effects of corrosion, fatigue cracking and local denting. Some considerations for establishing a reliability-based repair and maintenance scheme are also made so as to keep a ship's hull girder strength reliability at an acceptable level even later in life.

• Structural Engineering and Mechanics
• /
• v.15 no.2
• /
• pp.225-238
• /
• 2003

In the present study, the finite strip analysis of a box girder to simulate a ship's hull model is carried out to investigate its inelastic post-buckling behavior and to predict its ultimate flexural strength. Residual stresses and initial geometrical imperfections are both considered in the combined material and geometrical nonlinear analysis. The von-Mises yield criterion and the Prandtl-Reuss flow theory of plasticity are applied in modeling the elasto-plastic behavior of material. The Newton-Raphson iterative process is also employed in the analysis to achieve convergence. The numerical results agree well with the experimental data. The effects of some material and geometrical parameters on the ultimate strength of the structure are also investigated.

• Journal of Ship and Ocean Technology
• /
• v.12 no.1
• /
• pp.45-56
• /
• 2008

Recently, International Association Classification Societies (IACS) has adopted the Common Structural Rules (CSR) for Bulk Carriers and Tankers, which specifies the requirement associated with the ultimate strength of hull girder structure. The theoretical background and the results of verification study are neither well summarized nor released. Furthermore, the requirement is not a form of deterministic formula but a form of program in which source code is not disclosed. The reliability of the non-linear structural analysis program is verified through the comparison with the results of the analysis and the model test. Then, the reliability of the ultimate strength requirement in CSR is checked by comparing with the results of rigorous non-linear analysis.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.20 no.2
• /
• pp.96-104
• /
• 1984

This paper is on the prediction and response of the ship hull girder due to slamming of foreward flat bottom plate. The response with respect to foreward flat bottom is divided two kinds by estimating method. One is the estimation of impact forces by slamming, Another is the response of hull girder due to impact forces, that is, displacement, velocity, acceleration, etc. must calculate the values for considered ship hull girder. In this paper, therefore, was estimated only impact forces along ship ordinate of foreward. The analysis of data for estimation followed mainly papers of Ochi. These estimated data shall contribute for ship gull construction for basic optimum design. In particular, the estimated impact forces shall be given for the response of ship gull girder on the foreward flat bottom plate with characteristics of external forces.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.18 no.1
• /
• pp.35-38
• /
• 1982

Ship hull Vibration is caused by troubling measure instruments installed in the ship, fatigue of the hull girder. Vibration has been studied by the View point of anti-Vibration. However, the theoretical calculation values of the Vibration analysis were not obtained accurately. Therfore, in this paper, Vibration analysis were made on the two (cylinder form, ship form) of ship hull girder by the transfer matrix method. The super-structure length was determined to be 0, 20, 40, 60, 80, 100, percentage of the ship's length from the stern. The results of analysis by the transfer matrix method are as follow. 1. Natural frequency may be determined by the order of node numbers and superstructure length. 2. Natural frequency inereased when the ship form is a finess and increasing ratio followed by high order of node numbers.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2000.06a
• /
• pp.1185-1191
• /
• 2000

In general, the strength of hull structures can be estimated from stress evaluation considering static and hydro-dynamic load due to sea-wave. However, war ships such as submarine, have frequently experienced the underwater explosion and local structures of ship as well as hull girder can be damaged by the dynamic response excited from underwater non-contact explosion. When explosion happens at underwater, shock wave is radiated In early short time, then gas bubbles are generated, and expansion and contraction are repeated as they float to the surface. The shock wave causes the damage of equipment and its supporting structures, on the other hand, the hull girder strength can be lost by resonance between bubble pulsation and lowest ship natural vibration period. In this paper, the hydro-Impulse force due to bubble was calculated. Based on these results the hull girder strength of submarine was estimated from transient response analysis by using NASTRAN. Also, shock analysis for some equipment supporting structures was carried out by using DDAM. In order to evaluate the strength of these local structures due to shock wave.

• Special Issue of the Society of Naval Architects of Korea
• /
• 2007.09a
• /
• pp.99-106
• /
• 2007

The IACS Common Structural Rules are to be applied for double hull tanker of more than 150m length with contracted after 1 April 2006. The objectives of the rules are to make more robust, safer ship and to ensure transparency of the technical background. In compliance of CSR, we had carried out prescriptive rules scantling determination and 3-D hold FE analysis of AFRAMAX TANKER. Prescriptive rules scantling determines the minimum required scantling, hull-girder longitudinal bending and shear strength, hull girder ultimate strength, local strength of plate and stiffener, strength of primary supporting member and fatigue assessment of the longitudinal stiffener end connections to the transverse bulkhead. 3-D hold FE analysis assesses the structural adequacy of the vessel's primary hull structure and major supporting members using yielding and buckling failure modes. So we could verify the strength assessment of AFRAMAX TANKER applied CSR.

• Special Issue of the Society of Naval Architects of Korea
• /
• 2015.09a
• /
• pp.46-49
• /
• 2015

Common Structural Rules (CSR) about bulk carriers and double-hull oil tankers of International Association of Classification Societies (IACS) has been applied to ships contracted for construction since April 2006. By unifying each society's rules, the difference of opinion in the between shipyard and ship owners, classification was reduced, and CSR has been evaluated by rules the safety structure more enhanced. However, The CSR about the bulk carriers and double hull oil tankers, important design content standards, such as the local scantling calculation, static/dynamic load case and corrosion margin and etc., are different. Therefore in order to combine the CSR, the Harmonized CSR for bulk carriers and double hull oil tankers (H-CSR) was issued on 1, January, 2014, and will be apply to ships contracted for construction after 1st July 2015. It is necessary to verify the H-CSR to optimize the structural arrangement because effective date is not far off. In this study, we compared the impact by rule change for the hull girder shear strength of bulk carriers between CSR and H-CSR in respect of the yielding and buckling strength.

• Journal of the Society of Naval Architects of Korea
• /
• v.35 no.3
• /
• pp.54-61
• /
• 1998

This paper presents a prediction method of natural frequencies of vertical hull girder vibration based on design sensitivity analysis in case of design modification and the variation of loading condition. The resented method premises the vibration analysis by the transfer matrix method. Governing sensitivity equation is derived from the direct differentiation of state vector and transfer matrix to parameters and its transfer over all the hull girder elements. Derivatives of natural frequencies and mode shapes are determined by two trial calculation of the governing equation. Using the derivatives, the changes of natural frequencies and mode shapes can be predicted when mass and stiffness parameter's are changed. As results, it is possible to optimize ship structure as well as to avoid troublesome calculation in hull girder vibration analysis rationally and efficiently. To verify the accuracy and efficiency of the resented method numerical results obtained by both the sensitivity analysis and the ordinary reanalysis far a real ore/bulk carrier in case of the change of mass and stiffness parameters are compared.