• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2010년도 춘계학술발표대회
• /
• pp.39.2-39.2
• /
• 2010

Recently, hot stamping process has been paid attention greatly by automobile makers in accordance with the fuel efficiency and environmental issues as well as crash safety issue. The hot-stamped parts, however, demand extreme mechanical properties such as tensile strength of over 1470 MPa or equivalently Vickers hardness of around 450. In this work, to meet the demand efficiently, a method to predict mechanical property of hot-stamped parts based on numerical phase transformation scheme has been proposed associated with the thermo-mechanical coupled finite element analysis. This work deals with various phase transformation equations and validates them to select appropriate model for 0.2C-0.1Si-1.4Mn-0.5Cr-0.01Mo-0.002B steel sheet. The authors show that an efficient method saving time and cost to develop hot-stamped automobile parts ensuring suitable mechanical properties such as Vickers hardness and strength.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2006년도 춘계학술대회 논문집
• /
• pp.219-220
• /
• 2006

Laser surface hardening technologies have been used to improve characteristics of wear and to enhance the fatigue resistance for mold parts. The objective of this research work is to investigate the influence of the process parameters, such as power of laser and defocused spot position, on the characteristics of laser surface hardening for the case of SKD61 steel. CW Nd:YAG laser is selected as the heat source. The optical lens with the elliptical profile is designed to obtain a wide surface hardening area with a uniform hardness. From the results of the experiments, it has been shown that the maximum hardness is approximatly 740 Hv when the power, focal position and the travel of laser are 1,095 W, +1mm and 0.3 m/min, respectively. In addition, the hardening width using the elliptical lens was three time larger than that using the defocusing of laser beam.

• 한국정밀공학회지
• /
• 제24권4호
• /
• pp.57-67
• /
• 2007

Laser surface hardening technologies have been used to improve characteristics of wear and to enhance the fatigue resistance fur mold parts. The objective of this research work is to investigate the influence of the process parameters, such as power of laser and defocused spot position, on the characteristics of laser surface hardening for the case of SKD61 steel. CW Nd:YAG laser is selected as the heat source. The optical lens with the elliptical profile is designed to obtain a wide surface hardening area with a uniform hardness. From the results of the experiments, it has been shown that the maximum average hardness is approximatly 780 Hv when the power, focal position and the travel of laser are 1,095 W, 0mm and 0.3 m/min, respectively. In samples treated with lower scanning speeds, some small carbide particles appear in the interdendritic regions. This region contains fine martensite and carbide in proportions which depend on the local thermal cycle.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 추계학술대회 논문집
• /
• pp.287-290
• /
• 2002

Stainless steel used widely in various fields of industry have the characteristics of difficulty-to-cut. This difficulty comes from its peculiarity, for example work hardening, vibration, etc. And these peculiarity on the cutting process have an effect on tool wear or life shortness of tools. To solve these problems several method have been developed. Hot-machining is one way of these method. when a material is heated, organization of material is soften. So cutting process becomes easy. When such a hot-machining method applies on drilling process and then heated material is processed, cutting force is less than usual drilling process cutting force. In this paper, cutting force is compared heated SUS 304 with usual SUS 304. And shape of chips is also compared.

• 소성∙가공
• /
• 제13권5호
• /
• pp.435-440
• /
• 2004

The temperature in hot forming of metallic materials, such as hot extrusion and hot forging, ranges from $300^{\circ}C$ to $900^{\circ}C$. Correspondingly, the die also exhibits high temperatures close to that of a work piece and its life is limited generally by high temperature fatigue. Thus, the analysis of high temperature fatigue would need the mechanical properties over the wide ranges of temperature. However, very few studies on the high temperature fatigue of brittle materials have been reported. Especially, the study on the fatigue behavior over such transition temperature regime is very rare. In this paper, the stress-strain curves and stress-life curves of a die steel such as STD61 are experimentally obtained. The wide ranges of temperature from $300^{\circ}C$ to $900^{\circ}C$ are considered in experiments and the transition temperature zone is carefully examined.

• 소성∙가공
• /
• 제8권1호
• /
• pp.65-77
• /
• 1999

In recent years, the quality requirements from the customers of hot rolled steel strip have been steadily increasing in diversity and strictness. To meet these quality requirements as well as to improve productivity, steel mills have been doing their efforts for developing high performance Automatic Gauge Control (AGC) system. However, it is very time consuming and also needs a lot of money to develop the new technologies of AGC in actual mill. So, there has been a demand for developing the Dynamic Hot Rolling Simulator since late 80's. It is a kind of software packages and can analyze the dynamic behaviors of hot finishing rolling process without laborious experiments in actual mill. It can also be used as a designing tool of Automatic Gauge Controller. In this work, the Dynamic Hot Rolling Simulator which is applicable to 6 sands hot strip mill rolling was developed. The MATLAB with SIMLINK was used as a software developer for making the main part of simulator because it is very powerful tool for modeling, integrating, controller design, and simulation. In this paper, the structures and the mathematical models of the simulator were briefly described and the results of simulation on the transient phenomena of hot rolling process with actual mill data were also presented.

• 한국표면공학회지
• /
• 제34권4호
• /
• pp.327-336
• /
• 2001

The skinpassing conditions such as roll type, roll force and roll roughness of the work roll were evaluated to give the surface properties of the galvanized steel sheets that were required for automotive and to get rid of the surface defects that caused with the bad control of galvanized coating process parameters. The surface defects of the galvanized steel sheets such as the ripple mark and the scratch were completely removed as the roll force of SPM work roll was increased and the amount of the transfer of roll surface texture to the strip was also gained a lot. The image clarity of electro discharge textured (EDT) coated steel sheets before and after painting was higher than that of the bright (BRT) and shot blasted (SBT) coated steel sheets because of higher PPI value, lower waviness and uniform surface pattern. Since micro-craters transferred on the surface of the galvanized steel sheets played a role of nucleation sites of chromate reaction, Increase of micro-craters was bring to better corrosion resistance with the increase of the roll force and the use of EDT roll at the skin pass mill.

• 소성∙가공
• /
• 제15권2호
• /
• pp.118-125
• /
• 2006

API steel is used for line-pipe to transport the oil and natural gas. As the recent trends in the development of API steel are towards the use of larger diameter and thicker plate, many researches have been studied to achieve higher strength, higher toughness and lower yield ratio in API steel. However, the strength of API steel after pipe forming is changed depending on the competition of the Bauschinger effect and work hardening which are affected by the strain history during pipe forming process. So, the purpose of this study is to investigate the influence of microstructure on the Bauschinger effect for API steel. To change the microstructure of API steel we have changed the hot rolling condition and the amounts of V and Cu addition. The compression-tensile test and the microstructure observation by OM and TEM were conducted to investigate the yield strength drop and the correlation between the Bauschinger effect and microstructure of API steel. The experimental results show that the increase of polygonal ferrites volume fraction increases the Baushcinger effect due to the back stress which comes from the increase of mobile dislocation density at polygonal ferrite interior during the compressive deformation. The hot rolling condition was more effective on the Bauschinger effect in API steel than the small amount of V and Cu addition.

• Steel and Composite Structures
• /
• 제20권1호
• /
• pp.21-41
• /
• 2016

Cold-formed steel structures are increasingly attractive due to their benefits of good mechanical performance and constructional advantages. However, this type of construction is still not fully exploited as a result of the acknowledged difficulties involved in forming construction-efficient and cost-effective connections. Furthermore, there is a lack of information on the structural behavior of the cold-formed steel connections. In this study, the research on various cold-formed steel connections was comprehensively reviewed from both fundamental and structural points of view, based on the available experimental and analytical data. It reveals that the current design codes and guidelines for cold-formed steel connections tend to focus more on the individual bearing capacity of the fasteners rather than the overall structural behavior of the connections. Significant future work remains to be conducted on the structural performance of cold-formed steel connection. In addition, extensive previous research has been carried out to propose and evaluate an economical and efficient connection system that is obtained from the conventional connecting techniques used in the hot-rolled industry. These connecting techniques may not be suitable, however, as they have been adopted from hot-rolled steel portal frames due to the thinness of the sheet in cold-formed steels. The review demonstrates that with the increasing demand for cold-formed steel constructions throughout the world, it is crucial to develop an efficient connection system that can be prefabricated and easily assembled on site.

• 소성∙가공
• /
• 제10권3호
• /
• pp.206-213
• /
• 2001

Dynamic deformation of metallic materials mostly accompanies substantial amounts of deformation heat. Since the flow stress of deformation is sensitive to temperature, implication of heat due to plastic work is essential to the evaluation of constitutive relations. In this study, a series of compression tests were conducted for SAF 2507 super duplex stainless steel at various temperatures and strain rates. The accumulation of plastic work was calculated through numerical integration and converted into the elevation of temperature. Subsequent logarithmic interpolation deduced isothermal flow surfaces, which were primary input data of finite element analysis. Simple closed die forging process was analyzed and optimized with commercial FEM code applying both raw and calibrated material database. The effect of accounting deformation heat was more noticeable in high-speed forming process.