• Journal of Powder Materials
• /
• v.12 no.5 s.52
• /
• pp.357-361
• /
• 2005

Fe-doped skutterudite $CoSb_3$ with a nominal composition of $Fe_{x}Co_{4-x}Sb_{12}(0\;{\le}\;x\;{\le}\;2.5)$ has been synthesized by mechanical alloying (MA) of elemental powders, followed by hot pressing. Phase transformations during mechanical alloying and hot pressing were systematically investigated using XRD. Single phase skutterudite was successfully produced by vacuum hot pressing using as-milled powders without subsequent annealing. However, second phase in the form of marcasite structure $FeSb_2$ was found to exist in case of $x\;{\ge}\;2$, suggesting the solubility limit of Fe with Co in this system. Thermoelectric properties as functions of temperature and Fe contents were evaluated for the hot pressed specimens. Fe substitution up to x=1.5 with Co in $Fe_{x}Co_{4-x}Sb_{12}$ appeared to increase thermoelectric figure of merit (ZT) and the maximum ZT was found to be 0.78 at 525K in this study.

• Composites Research
• /
• v.20 no.4
• /
• pp.9-17
• /
• 2007

Powder metallurgy has been employed for the development of SiC particle reinforced aluminum metal matrix composites by means of hot isotropic pressing and vacuum hot pressing. A material model based on micro-mechanical approach then has been presented for the processes. Densification occurs by the inelastic flow of matrix materials during the consolidation, and consequently it depends on many process conditions such as applied pressure, temperature and volume fraction of reinforcement. The model is implemented into finite element software so that the process simulation can be performed enabling the predicted relative density to be compared with experimental data. In order to determine the performance of finished products, further tensile test has been conducted using the developed specimens. The effect of internal void of the materials on mechanical properties therefore can be investigated.

• Journal of the Korean Ceramic Society
• /
• v.35 no.6
• /
• pp.551-558
• /
• 1998

Detection of microcrack in {{{{ {Al }_{2 } {O }_{3 } }} ceramics were studided by AE(acoustic emission) technique with 4-point bending test in order to evaluate the fracture process and formation of microcrack. Fully-dense alu-mina ceramics having a different grain size were fabricated by varing the hot-pressing temperature. The grain size of alumina increased with increasing the hot-pressing temperature whereas the bending strength decreasd. The microcracks were observed by SEM and TEM. The generation of AE event increased with increasing the applied load and many AE event was generated at maximum applied load. Alumina with smaller grain size shows the generation of many AE event resulting in an increase of microcrack formation. An intergranular fracture is predominantly observed in fine-grained alumina whereas intragranular fracture occurs predominantly in coarse-grained alumina,. Analysis of micorstructure and AE prove that primary mi-crocracks occur within grain-boundaries of alumina. The larger microcracking were formed by the growth and/or coalesence of primary microcracks. Then the materials become to fracuture by main crack gen-eration at the maximum applied load.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2009.10a
• /
• pp.267-270
• /
• 2009

In the present investigation, we are newly developing a new forming process which can fabricate micro patterns on large-area polymeric substrates for high speed mass production. The key idea of the new process is to pressurize multiple vacuum-packed substrate-mold stacks above the glass transition temperature ($T_g$) of the polymeric substrates. The new process is thought to be promising micro-pattern fabrication technique in three aspects; firstly, isostatic pressing ensures the uniform micro-pattern replicating condition regardless of the substrate area. Secondly, the control of forming condition such as temperature and pressure can realize well-defined process condition exploited in the conventional hot embossing research field. Thirdly, multiple substrates can be patterned at the same time. A prototype forming machine for the new process was developed with the design consideration realizing the present idea. With a developed machine, micro prismatic array patterns with 50 um in size were successfully made on the $380{\times}300{\times}6\;mm$ PMMA plate.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 1994.05a
• /
• pp.59-60
• /
• 1994

• Journal of the Korean Ceramic Society
• /
• v.33 no.3
• /
• pp.259-268
• /
• 1996

In the present study the effect of the addition of Fe on the pressureless and hot press sintering behavior was studied under Ar atmosphere. Pressureless sintering was performed 1900~220$0^{\circ}C$ under. Ar atmosphere. The addition of 1 wt% Fe was increased effectively of the sintered density. However it was impossible to obtain high density higher than 90%,. Zr-Fe-B compound in liquid phase was observed from the EDS and WDS analysis. It was considered that sinterability was enhanced due to the mass transfer through Fe based liquid phase formed at the sintering temperature. Hot pressing was performed at 1600~1$700^{\circ}C$ under Ar atmos-phere for 1 hr. It was possible obtain 95% relative density of ZrB2 specimen which is higher density at pressure-less sintering. It could be thought that ZrB2 particles was rearranged through liquid phase by applied pressure during initial stage of sintering.

• Journal of Adhesion and Interface
• /
• v.7 no.3
• /
• pp.16-25
• /
• 2006

Water vapour permeable and water resistant film was laminated to made footwear woven fabric and non-woven fabrics by screen type with thermosetting reactive hot melt adhesive. Optimum conditions of each process were investigated, and the properties of film laminated fabric with optimum conditions are evaluated. The results are as follows. Thermosetting reactive polyurethane hot melt is retain proper heat resistance differently thermoplastic hot melt. Optimum melting adhesive process conditions are as follows ; drum temperature $95^{\circ}C$, hose temperature $97^{\circ}C$, feeding pipe temperature $100^{\circ}C$, screen temperature $105^{\circ}C$, pressure of opposite roller $1kgf/cm^2$, pressure of laminating roller $3kgf/cm^2$, finishing speed 15 m/min, melting temperature $120^{\circ}C$, cooling time 20 s, pressing temperature $130^{\circ}C$, pressing time 30 s. As the thickness of film was increased, the water vapour permeability was decreased but water resistance was increased, and the effect of film is dominant over all the others in the air permeability.

• Journal of the Korean Electrochemical Society
• /
• v.2 no.4
• /
• pp.190-194
• /
• 1999

Etched Nafion membrane and electrode assemblies were fabricated and those performances were observed in PEMFC. Adhesion of membrane to electrode increased with abrasion of membrane surface. Membrane surface ething results in reduction of hot pressing temperature, as a consequence, in improving of cell performance. It was found that Nafion etching was effective in painting method. The optimum content of electrode catalyst should be selected according to etching intensity.

• Journal of the Korean Ceramic Society
• /
• v.41 no.3
• /
• pp.202-209
• /
• 2004

Hydroxyapatite(HA)/TiO$_2$ composite powders were prepared by mixing of spherical TiO$_2$ (10-15 nm, 500 nm) and needle-shaped HA (50-70 nm, 120-250 nm) powders which had been synthesized through precipitation, sol-gel and hydrothermal methods. From the three types of starting composite powders (HA/TiO$_2$ wt% of 75/25, 50/50, and 25/75), dense $\beta$-TCP/TiO$_2$ composites were prepared by hot-pressing at 800-100$0^{\circ}C$ for 30 min under the pressure of 30 ㎫ in Af atmosphere. The $\beta$-TCP/TiO$_2$ composites showed different microstructures and sintering densities depending on their powder morphology, composition and sintering temperature. With increasing the sintering temperature and the content of TiO$_2$, sintered density was increased and microstructure became more homogeneous.

• Journal of Powder Materials
• /
• v.4 no.1
• /
• pp.48-54
• /
• 1997

NiAl powders containing oxide dispersoids have been produced by mechanical alloying process in a controlled atmosphere using high energy attrition mill. The powders have been consolidated by hot extrusion and hot pressing followed by isothermal annealing to induce microstructure coarsening to improve high temperature properties. Grain growth and dispersoid coarsening kinetics have been investigated as functions of annealing time and temperature. Coarsening of dispersion strengthen NiAl and dispersoid has been discussed. Some clues of secondary recrystallization have been investigated. Mechanical property measurements have been also made and correlated with the microstructures.