• Food Science and Biotechnology
• /
• 제14권5호
• /
• pp.661-666
• /
• 2005

The specific objectives of this study were to dry yam chips using microwave vacuum drying, freeze drying and hot air drying, then to coat the dried yam chips with ascorbic acid cocrystallized sucrose, and finally to compare the quality of yam chip snack foods with respect to drying and coating characteristics. The microwave vacuum dried sample showed the highest drying rates and much less surface damage than the hot air dried one did. The shape and color of the microwave vacuum dried/coated sample were allocated between those of the freeze dried/coated sample and the hot air dried/coated sample. The freeze dried/coated sample scored excessively low in organoleptic hardness and chewiness to be suitable as a snack. The hot air dried/coated sample was too deep in color, wrinkled, excessively high in organoleptic hardness and chewiness, and excessively low in mouthfeeling. Therefore, the microwave vacuum dried/coated sample presented the best overall attributes as a snack, with respect to organoleptic characteristics, shape, color, and drying rates.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2011년도 추계학술대회 초록집
• /
• pp.115-115
• /
• 2011

Biodiesel (BD) was made from animal-fats reacting with methanol and potassium hydroxide in the laboratory. The biodiesel made in the laboratory was sent to K-petro, the government agency, to inspect the quality of animal-fats biodiesel, of which generally the quality was acceptable for heating oil for agricultural hot air heater. Kinematic viscosity and calorific values of the biodiesels were measured. BD20(K), kerosene based biodiesel, showed 18cSt at $-20^{\circ}C$. It seems that BD100 can not be suitable for heating fuel under some temperature. As BD content increased calorific value decreased, up to 40,000J/g for 100% BD, while light oil calorific value was 45,567J/g, showing difference of 5,567J/g, about 12% difference. Several different fuels, BD20, BD50, BD100 and light oil, were prepared and tested for fuel combustion qualities for agricultural hot air heater and their combustion performances were compared and analyzed. Flame dimensions of biodiesels and light oil were almost same shape at the same combustion condition in the burner of the hot air heater. Generally $CO_2$ amounts of BDs are greater than light oil. But,the differences are so small that it is hard to tell there was significant difference existed between the BDs combustion and light oil.

• 한국식생활문화학회지
• /
• 제38권5호
• /
• pp.356-364
• /
• 2023

This study compared the physicochemical properties of soybean curd residue and black soybean curd residue produced by hot air-drying and freeze-drying. Regardless of drying method, the crude protein, crude ash, crude fiber contents, pH, L, a, b color values and water soluble index were higher in soybean curd residue, whereas total polyphenol contents and antioxidant activity were higher in black soybean curd residue. Significant differences in water absorption index, oil absorption capacity and emulsion activity were observed between soybean curd residue and black soybean curd residue in freeze-drying. On the other hand, the emulsion stability was not significant difference in both hot-air drying and freeze-drying. The crude protein and crude fiber contents of soybean curd residue were not significant difference between hot-air drying and freeze-drying. Freeze-drying resulted in higher crude ash contents, pH, water absorption index, water soluble index, oil absorption capacity, emulsion activity and emulsion stability than hot-air drying. Hot-air drying have caused significantly higher water contents, water activity, total polyphenol contents and antioxidant activity in soybean curd residue than freeze-drying. In conclusion, soybean type and drying methods affect the physicochemical and quality characteristics of soybean curd residue, which could be important factors in the manufacture of processed foods.

• 한국태양에너지학회 논문집
• /
• 제24권1호
• /
• pp.53-61
• /
• 2004

Absorption potential of desiccant solution significantly decreases after absorbing moisture from humid air, and a regeneration process requires a great amount of energy to recover absorption potential of desiccant solution. In an effort to develop an efficient solar water heater, this study examines a regeneration process using hot water obtained from solar water heater to recover absorption potential by evaporating moisture in the liquid desiccant. In this paper, a solar absorption dehumidifying system with solar water heater is suggested to save the electricity for operating an air conditioner. LiGl(lithium chloride) solution was adopted as a liquid desiccant in the proposed system, and hot water obtained from the solar water heater was used for regenerating the liquid desiccant. As a result, it was clear that the dilute LiCl solution could be regenerated by hot water, and the regeneration rate depends mostly on temperature level of liquid desiccant. The regeneration rates were about 2.4kg/h with $40^{\circ}C$, 4.0kg/h with $50^{\circ}C$, and 6.2kg/h with $60^{\circ}C$ of hot water respectively.

• 대한설비공학회지:설비저널
• /
• 제15권4호
• /
• pp.362-371
• /
• 1986

In the normal Refrigeration process, the condensation heat of refrigerant s not been used because of its low-temperature waste heat. To recover the condensation waste heat of R-12 refrigerator, a drying and hot water system was designed and experimented. The results obtained were summarized as follows: 1. As the temperature a temosphere was increased, the temperature of discharge gas of compressor was increased. And the temperature was $80-84^{\circ}C$ for air condensing type and was $68-71^{\circ}C$ for water condensing type during summer. 2. The condensation waste heat could be obtained up to $50-55^{\circ}C$ of drying heat-source and Hot water in summer. In this case, recovered rate was about $73\%$. And the more temperature of drying Heat-source and Hot water were increased, the more a recovered rate were decreased. 3. When comparing drying characteristics of Agro-products in dryer of waste heat utilization and Hot air, there was no quality difference in products. But drying time of the former was 3 Hours longer than the latter. 4. The condensation waste heat of compressor could be applied into the drying of marine products, the predrying of agro-products and making hot water. And showed high possibility of the waste heat using in low-temperature storage.

• Journal of Biosystems Engineering
• /
• 제34권3호
• /
• pp.155-160
• /
• 2009

This study was attempted to quality characteristics of ginseng powder using molecular press dehydration(MD) method. Ginseng powder was dried using maltodextrin as dehydrating agents, and the quality of the ginseng powder was compared with that of freeze-drying and hot air-drying samples in terms of colors, moisture contents and grain size. The colors of ginseng powder using MD-drying and freeze-drying was better than hot air-dried ginseng powder. The moisture contents of ginseng powder using MD-drying was 9.49%, while freeze-drying was 4.14% and hot air-drying 11.71% after 72ball mill times. The grain size of ginseng powder using MD-drying and freeze-drying was better than hot air-drying ginseng powder. These results suggest that drying of ginseng powder using molecular press dehydration method is very efficient, because minimal cell destruction may be achieved.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2018년도 추계 학술논문 발표대회
• /
• pp.4-5
• /
• 2018

The water proofing sheet of synthetic polymer applies to the purification plant, the wastewater treatment center, the low waterway, the dosing tanks, etc, and when we construct these, we apply the dual waterproof by means of hot air staking welder or extruder. However, the experts skilled in the hot air welding or extruder does not use them, it can be a quality problem. Therefore, in this study, it is the purpose to verify whether the semi-automatic hot air staking welder and automatic extruder that can construct the waterproof sheet is possible in field even if it is not a professional specialist.

• International Journal of Air-Conditioning and Refrigeration
• /
• 제15권4호
• /
• pp.175-181
• /
• 2007

A computer model of a high efficiency refrigeration system equipped with heat storage for reverse cycle-hot gas defrost (the stored heat is used during defrost cycle of the system) is presented. The model was developed based on both theoretical and empirical equations for the compressor, evaporator, condenser and the heat storage equipment. Simulations of the prototype system were carried out to investigate refrigeration system performance under various operating conditions during refrigeration cycles. The simulations of the evaporator during defrost cycles at 30 and $40^{\circ}C$ hot gas refrigerant temperature were also performed which resulted on shorter defrost time but only slight increase in defrost efficiency. These information on energy efficiency and the defrost time required are important in order to avoid excessive parasitic load and temperature rise of the refrigerated room.

• 한국산업융합학회 논문집
• /
• 제26권2_2호
• /
• pp.255-263
• /
• 2023

The shell and tube-type heat exchangers have been frequently used in many industrial field because of its simple structure and wide operation conditions and so on. The purpose of this study is to investigate the flow characteristics in single shell of shell and tube-type heat exchanger according to velocity and temperature of hot air released from heat exchanger simulator through numerical analysis. As the results, the temperature was decreased in almost quadratic curve from top to bottom in single shell of the shell and tube-type heat exchanger. Further the changes of pressure and velocity in outlet according to change of inlet temperature were not observed. The cost for operating the shell and tube-type heat exchanger should be compared the supply cost of hot air with that of velocity in order to make a economic decision.

• 한국생물환경조절학회:학술대회논문집
• /
• 한국생물환경조절학회 2000년도 학술발표논문집 Proceeding of Bio-Environment control
• /
• pp.13-17
• /
• 2000