In magnetic hard disk drives, higher areal recording density requires reduction of head-disk spacing. To overcome the increase of stiction associated with reduction of head-disk spacing, a padder slider, which adds pads to slider's air bearing surface, can be one of the practical solution for sub 20 nm flying height, and even for near contact recording. This study investigated the tribological characteristics of a padder slider. A padder slider took off slowly but showed less friction force than a normal slider. The hot/dry CSS test and drag test indicated that pad wear of a padder slider was negligible. The tribological performance of disk is an important factor to be considered. In particular, less carbon overcoat layer of the disk will result in higher stiction and wear in slider/disk interface. In conclusion, a padder slider shows encouraging tribological performances for practical use in HDD.
The fans installed in standard Hanwoo loose barns (room size : 10 m (width) $\times$ 5 m (length)) are frequently used to reduce Hanwoo's heat stress during hot weather and to dry the wet floor. However, the most effective method of installing fans has not been suggested yet. Therefore, this study was carried out to evaluate two methods of installing fans under the ceiling of Hanwoo loose barn by using CFD (Computational Fluid Dynamics) code, FLUENT and to recommend the optimum fan installing method. The fan installation options were fan tilting angles of $45^{\circ}$ and $0^{\circ}$ (horizontal). The fans of 1 m diameter were installed at 3 m above floor. A velocity scale on 10 cm and 110 cm above floor and air flow pattern were used as the parameters to evaluate the fan installing methods. The fans tilted at $45^{\circ}$ angle produced higher wind at 10 cm and 110 cm above floor and more uniform air flow pattern, compared with the fans installed horizontally. Based on these results, fans tilted at $45^{\circ}$ angle may help to reduce Hanwoo's heat stress and will dry the floor better than fans installed horizontally. Therefore, it is suggested that the fans of 1 m diameter in a standard Hanwoo loose barn should be installed at a $45^{\circ}$ tilt angle and 3 m above floor with spacing of 5 m at the center of a room column.
Korean Journal of Air-Conditioning and Refrigeration Engineering
/
v.8
no.1
/
pp.1-12
/
1996
In lots of application to heat exchanger systems, closed two-phase thermosyphons are tilted from a horizontal. If the tilt angle, especially, is less than 30$^{\circ}$, the operational performances of thermosyphon are highly dependent on tilt angle. The present study was conducted to better understand such operational behaviors as mech-anni는 of phase change, and flow patterns inside a tilted thermosyphon. For experiment, an ethanol thermosyphon with a 35% of fill charge rate was designed and manufactured, using a copper tube with a diameter 19mm and a length 1500mm. Through a series of test, the tilt angle was kept constant at each of 4 different values in the range 10~25deg. and the heat supply to the evaporator was stepwisely increased up to 30㎾/$m^2$. When a steady state was established to the thermosyphon for each step of thermal loads, the wall temperature distribution and vapor temperature at the condenser were measured. The wall temperature distributions demonstrated a formation of dry patch in the top end zone of the evaporator, with a values of temperature 20~4$0^{\circ}C$ higher than the wetted surface for a moderate heat flux q≒20㎾/$m^2$. Inspite of the presence of hot dry patch, however, the mean values of boiling heat transfer coefficient at the evaporator wall were still in a good agreement with those predicted by Rohsenow's formula, which was based on nucleate boiling. For the condenser, the wall temperatures were practically uniform, and the measured values of condensation heat transfer coefficient were 1.7 times higher than the predicted values obtained from Nusselt's film condensation theory on tilted plate. Using those two expressions, a correlation was formulated as a function of heat flux and tilt angle, to determine the total thermal resistance of a tilted thermosyphon. The correlation formula showed a good agreement with the experimental data within 20%.
In order to prevent the environmental pollution, the dryers are commonly used to treat sludge that one of sewages is polluting the quality of water. Generally, the drying method is various as to the property of material and use. Rotary dryer is a good apparatus to treat them. The rotary dryer is the way that is to make substance transmission and heating using hot air between sludge particles and heated gas. In this paper, we performed a numerical analysis of the inner air flow of the 3-pass rotary dryer through the changing rotational speed from 3rpm to 10rpm. In this result, we found that 3rpm is effective to dry material in terms of heat transfer because large scale velocity fluctuation is occurred inside the first and second drum. Also we confirmed that 5rpm and 8rpm showed up uniform flow at the center area of the first drum.
This work was to study drying characteristics of the brown rice koji, an enzymic health food, using microwave under vacuum. Cooked brown rice was inoculated with Aspergillus oryzae and incubated at $32^{\circ}C$ for 6 days. The brown rice koji was dried by different drying methods: microwave vacuum drying, hot air drying, vacuum drying and freeze drying. Each drier except freeze drier was set to maintain the sample temperature at $40^{\circ}C$. During microwave vacuum drying, the sample reached $40^{\circ}C$ much faster (within $5{\sim}10\;min$) and was dried much faster (2 hrs) than the other drying methods. The initial drying rate of microwave vacuum drying was ten times faster than that of hot air drying. The microwave vacuum drying produced a dry sample of the highly retained enzymic activity, followed by freeze drying, vacuum drying, and hot air drying.
This work was to study the potential use of germinated and microwave-vacuum-dried brown rite as a raw material for enzyme food. Brown rice was soaked in water at $15^{\circ}C$ for 2 days and then germinated at $25^{\circ}C$ for 4 days. The germin ated brown rice was then dried by different drying methods: microwave vacuum drying 1(drying only), microwave vacuum drying 2 $(drying{\rightarrow}crushing{\rightarrow}drying)$, hot air drying, vacuum drying and freeze drying. Each drier except freeze drier was set to maintain the sample temperature to be $60^{\circ}C$. During microwave vacuum drying 1 and 2 the sample reached $60^{\circ}C$ much faster (5 min) and was dried much faster (2 to 3 hrs for microwave vacuum drying 1 and 2 than the other drying methods. The initial drying rate of microwave vacuum drying was ten times faster than that of hot air drying. The microwave vacuum drying produced a dry sample of the highly retained enzymic activity, followed by freeze drying, vacuum drying and hot air drying.
To provide the basic data to dry vegetate the sweetpotato leaves, the total contents of tannin, flavonoid and polyphenol in the methanol extract from the hot-air dried sweetpotato leaves were analyzed and DPPH radical scavenging activity, ABTS radical scavenging ability, nitrite scavenging ability, and others were comparatively analyzed. The total tannin content was decreased from Shinmi of 10.87 mg/g at $40^{\circ}C$ to 7.28 mg/g at $70^{\circ}C$ and the total flavonoid was decreased from Hayanmi of 55.37 mg/g at $40^{\circ}C$ to 39.63 mg/g at $70^{\circ}C$. That is, the low temperature drying contained more of these substances than in the high temperature drying. The DPPH radical scavenging activity was the highest in Shinmi and Hayanmi of 84.33% and 85.25% at $40^{\circ}C$, and the ABTS radical scavenging ability was a high value of over 80% in the treatment plot at $40^{\circ}C$. The nitrite scavenging ability was highest in Shinmi and Hayanmi of 76.15% and 73.74% at $40^{\circ}C$ but low at $70^{\circ}C$. That is, the antioxidant effect of the hot-air dried sweetpotato leaves was high in the sample of $40^{\circ}C$ and low in the sample of $70^{\circ}C$. Affected by the drying temperature, the high antioxidant effect is resulting from the little decrease of active ingredient when drying at low temperatures.
This study examined the optimal salting drying method and processing conditions (salt concentration, curing time, dry temperature, and drying time) for preparing salted semi-dried common gray mullet (SSD-CGM) Mugil cephalus based on the moisture content, salinity, and overall acceptance using response surface methodology (RSM). The moisture content, salinity, and overall acceptance of SSD-CGM prepared with different salting methods revealed that dry salting was the optimal salting method for preparing high-quality SSD-CGM. The optimal drying method for preparing high-quality SSD-CGM based on the drying velocity and sensory color was hot air-blast drying. The results of the RSM program indicated that the optimal independent variables ($X_1$, salt concentration; $X_2$, curing time; $X_3$, dry temperature; $X_4$, drying time) based on the dependent variables ($Y_1$, moisture content; $Y_2$, salinity; $Y_3$, overall acceptance) for high-quality SSD-CGM were 5.6% for $X_1$, 2.7 h for $X_2$, $47.0^{\circ}C$ for $X_3$, and 8.5 h for $X_4$ for uncoded values. The predicted values of $Y_1$, $Y_2$, and $Y_3$ for SSD-CGM prepared under optimal conditions were 54.4%, 4.2%, and 6.3, respectively, while the experimental values were $55.2{\pm}1.0%$, $4.1{\pm}0.3%$ and $6.7{\pm}0.8$. The actual and predicted values did not differ.
Ku, Kyung-Hyung;Lee, Kyung-A;Kim, Young-Lim;Lee, Yong-Whan
Journal of the Korean Society of Food Science and Nutrition
/
v.35
no.6
/
pp.780-785
/
2006
The composition analysis of various radish (Rapharnus sativus L.) leaves and the effects of drying condition on the quality characteristics of hot-air dried radish leaves were carried out by a response surface methodology. Independent variables put in drying temperature $(X_1)$ and drying time $(X_2)$, dependent variables put in color, calcium, iron, vitamin, etc. In the proximate composition of radish leaves by varieties, there were no significant differences in the ash, protein, lipid, calcium and iron content of samples, but there were significant differences in the vitamins, chlorophyll and color value of samples. The quality characteristics on dried radish leaves by central composite design, it was significant value on the moisture content, chlorophyll and color value according to drying temperature and drying times. But there were no significant differences in the contents of calcium $(31.41{\sim}35.80\;mg/g,\;dry\;base)$ and iron $(0.21{\sim}0.29\;mg/g\;dry\;base)$. The multiplex regression coefficients analysis were calculated with independent variables $(X_1,\;X_2)$ and dependent variables (moisture, chlorophyll, color value). The calculated coefficient correlations for the each samples were $R^2>0.97$. The effects of drying temperature were greater than drying time in the total chlorophyll content changes of radish leaves. Based on the present study, the optimum drying condition for the lowest color changes and effective reduction of moisture of radish leaves were expected to be $5{\sim}6$ hours at $70^{\circ}C$.
Background: This study was aimed at evaluating the growth, yield, and carbohydrate content in the whole Allium hookeri plant with shading treatment in hot summer. Methods and Results: Different shading rate, including 0 (control), 35 or 55%, was employed from the June $21^{st}$ to August $31^{st}$. Daily average air and soil temperature, which were approximately $2.5^{\circ}C$ and $3.8^{\circ}C$ lower, respectively, were observed with both 35% and 55% treatments in July and August, with no significant difference in daily maximum air temperature. Dry weights were high, approximately 40% and 48% for the shoot and 20% and 12% for the root, with the 35% and 55% treatments, respectively, 8 weeks after shading. Division number was increased by 13% and 19.8% with the 35% and 55% treatments, respectively. The mortality rates of 150 plants were 9.1%, 4.0%, and 1.3% with the 0 (control), 35% and 55% treatments, respectively. At 4 weeks after shading, the highest and lowest sucrose levels in both shoot and root were observed with the 35% and 55% treatments, respectively. At 8 weeks after shading, there was no significant difference in the sucrose content in the shoot among the treatments. Conclusions: The highest plant growth rate and yield with the 55% treatment may be related with the decrease in both air and soil temperatures, resulting in reducted leaf respiration and thus compensate net photosynthesis.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.