• 한국터널지하공간학회 논문집
• /
• 제8권1호
• /
• pp.65-76
• /
• 2006

기존의 NATM과 같은 터널공법에서는 불착 직후 벽연은 숏크리트나 록볼트에 의하여 지지되기 때문에 재래공법과 비교하여 암반의 느슨함을 감소시킬 수 있으나, 막장은 통상 무지보 상태로 놓여있기 때문에 붕괴의 위험성을 항상 내포하고 있는 것이 현실이다 현재 국내 터널시공시에는 막장이 굴진방향에 직립합A로써 응력의 집중이 발생하며 또한 막장의 안정성을 우려하여 단연분할공법을 채택하는 것이 일반적 공법으로 되어왔다. 그러나 이러한 방법은 경제적우로 큰 부당이 되며 공사기간 연장의 한 원인이 된다. 따라서 곡연막장 굴착공법을 개발하여 적용한다면 보다 나은 응력상태를 유지할 수 있어 1회 불진장의 증대 및 분할공법을 피함으로써 공사비절감 및 공사기간 단측에 매우 유리할 것이라 판단된다.

• 한국해양공학회지
• /
• 제18권3호
• /
• pp.8-12
• /
• 2004

The anchor is laid on the seabed, and the main engine is working against incident environmental loads in a typhoon. As the main engine is broken Mum in the storm, the anchor chain is cut and the vessel drifts. Although a ship is moored by two-point mooring lines to maintain her position, it has crashed into a rock because of a typhoon, resulting in a possible accidental oil spillage. In this paper, we studied maintenance of a ship's position, which is analyzed based on the slow motion maneuvering equations considering wave, current, and wind. To estimate wave loads, the direct integration method is employed. The current forces are calculated, using MMG (Mathematical Modeling Group). Th two-point mooring forces are quasi-statistically evaluated, using the catenary equation. Th coefficients of wind forces are modeled from Isherwood's empirical data, and the variation of wind speed is estimated by wind spectrum. The nonlinear motions of a two-point moored ship are simulated, considering wave, current, and wind load, in specific domain of time.

• 대한토목학회논문집
• /
• 제8권2호
• /
• pp.155-166
• /
• 1988

본 연구는 복합체의 단부영향을 고려한 등각균등질, 이방성의 모델개발과 이에따른 유한요소해석 프로그램 개발에 중점을 두었다. 복합체는 2차원의 수평층을 가지며 선형, 탄성, 작은변형에 제한을 두었다. 본 연구에서 개발된 등가 균등질의 이론은 복합체의 전반적인 거동을 포함시킴은 물론 층과 수직인 경계면과 그 부근에 형성되는 단부의 영향과 층의 경계면에 생기는 응력집중 현상을 나타낼 수 있게 하였다. 이론개발에 있어 1차변수는 $C_0$연속의 유한요소 근사치를 가지도록 하였으며 이를위해 최고 1차의 미분치가 변형에너지에 나타나도록 변수를 택하였다. 결과적으로 유한요소해석은 매우 간단하고 경제적이었으며 이들의 정당성과 정확도를 입증하기위하여 여러하중 조건하의 복합체를 풀이하였다.

• 한국연초학회지
• /
• 제20권2호
• /
• pp.231-237
• /
• 1998

This study was carried out to investigate the effects of curing methods on the concentration of ammonia during curing in burley tobacco leaves. The air-cured tobacco(KB108; Nicotiana tabacum L.) was grown at Chonju Tobacco Experiment Station in 1998 and the tenth leaves from the top on the stalk were harvested. Half of the harvested leaves were cured in normal air curing facility and the other leaves were cured in excessive curing facility. Stalk cut tobaccos were cured in horizontal curing facility. The leaves were sampled every five days from harvesting time to the end of curing(25 days). Ammonia concentration of leaves increased during curing period with a remarkable increase at yellowing stage. The concentration of ammonia was high in the primed cured leaves, while that of the excessive cured leaves was low. It is considered that the lower increase of ammonia in stalk cured leaves may be caused by the translocation from the leaves to the stalk during curing, while that of excessive cured leaves may be caused by the poor decomposition of protein and amino acid during curing by excessive moisture loss and high temperature condition.

• 센서학회지
• /
• 제26권4호
• /
• pp.274-279
• /
• 2017

LCD(Liquid Crystal Display) panel cutting problem is a sort of two dimensional cutting stock problem. A cutting stock problem is problem that it minimizes the loss of the stock when a stock is cut into various parts. In the most research of the two dimensional cutting stock problem, it is supposed that the relative angle of a stock and parts is not important. Usually the angle is regarded as horizontal or perpendicular. In the manufacturing of polarizing film of LCD, the relative angle should be maintained at some specific angle because of the physical and/or chemical characteristics of raw material. We propose a mathematical model for solving this problem, a two-dimensional non-Guillotine cutting stock problem that is restricted by an arranged angle. Some example problems are solved by the C++ program using ILOG CPLEX classes. We could get the verification and validation of the suggested model based on the solutions.

• 한국전기전자재료학회논문지
• /
• 제11권7호
• /
• pp.557-564
• /
• 1998

A low loss x-cut $LiNbO_3$optical waveguide was fabricated by Yi in-diffusion, and the properties of guided-mode and the total insertion loss of the pigtailed waveguide with polarization maintaining fiber(PMF) were measured at optical wavelength 1550nm. for forming the waveguides, the parameters of diffusion, Ti thickness, waveguide line-width, length, diffusion temperature, time and atmosphere were set $1400{\AA}$, $8{\mu}m$, 3.3cm, $1050^{\circ}C$, 8 hours and wet bubbled oxygen, respectively. And then after the polishing and piatailing, it showed that the total insertion loss was -4.1dB for TM mode, -5.5dB for TE mode, and mode size, that is, the horizontal/ vertical size were $13.8{\mu}m/18{\mu}m$ for TM mode, $9.6{\mu}m/6.5{\mu}m$ for TE mode.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2006년도 추계 학술논문 발표대회 논문집
• /
• pp.91-94
• /
• 2006

The way to shorten a construction period is considered to an very important technology development element as reducing the formwork removal periods with promoting strength revelation own concrete. This study executed experiment to review usability of early strength revelation chemical admixture which is judged in ways effective with premature removal of form about concrete. Use of early strength revelation AE water reducin admixture is apperaing so that strength revelation by early hydration promotions is excellent. The results of being applied proposed work process are that compressive strength are appeared more than 5MPa within 16 hours so that removal of vertical form was possible. the concrete compressive strength satisfied with a more than 2/3 of specified concrete strength for removal of horizontal form are appeared in 42 hours of 27 MPa proportioning strength, in 36 hours of 30, 35 MPa proportioning strength so that the 6 days cycle time of concrete structural frame work is cut by 2 days as shortening delayed period in works of removing slab forms. So construction cost reductions and a construction period shortening are judged so that it is possible.

• 한국통신학회논문지
• /
• 제37권7B호
• /
• pp.606-612
• /
• 2012

가시광 통신은 반도체 LED를 이용하여 정보를 브로드캐스트 하며, 백색광 LED는 조명과 광무선 통신을 하나의 광원을 사용하여 제공할 수 있다. 본 논문에서는 단일칩 백색광 LED를 활용하여 조명과 통신에 적합한 조명기구를 제안한다. 백생광 LED 조명기구의 구조에 따른 수평 조도특성, 무선채널 대역특성, 심볼간 간섭현상, 신호대 잡음비 및 비트 에러율을 분석함으로써 장애물이 있는 경우 제안한 LED 조명이 기존의 조명보다 우수한 조명 및 통신 채널을 제공함을 보이고자 한다.

• 한국지열·수열에너지학회논문집
• /
• 제17권1호
• /
• pp.23-32
• /
• 2021

Conventional wind power generators have limited installation sites due to low efficiency due to reverse resistance or high cut-in speed. To compensate for these problems, this study proposed another new type of tilting wind turbine. The key to this method is the structural design of a cylindrical cam with a guide groove that allows the blade to tilt. As the blade rotates by the cam, it tilts according to the angle. In the section that generates torque by receiving drag, the blade is made perpendicular to the wind. And it is a structure that creates a parallel state with the wind in the section where reverse resistance occurs. We prepared six types of cams considering the length of the section subject to drag, reverse resistance, tilting section. The performance was analyzed as the maximum value of the output, torque coefficient, and efficiency coefficient, which is indicated by setting different wind speed and low TSR.

• Geomechanics and Engineering
• /
• 제34권2호
• /
• pp.187-195
• /
• 2023

Intensive rainfall during the summer season in Korea has triggered numerous devastating landslides outside of downtown in mountainous areas. The 2D slope stability analysis that is generally used for cut slopes and embankments is inadequate to model slope failure in mountainous areas. This paper presents a new 3D slope stability formulation using the global sliding vector in the limit equilibrium method, and it uses an ellipsoidal slip surface for static and quasi-static analyses. The slip surface's flexibility of the ellipsoid shape gives a lower FS than the spherical failure shape in the Fellenius, Bishop, and Janbu's simplified methods. The increasing sub-columns of each column tend to increase the FS and converge to a steady value. The symmetrical geometric conditions of the convex turning corners do not indicate symmetrical failure of the surface in 3D analysis. Pseudo-static analysis shows that the horizontal seismic force decreases the FS and increases the mass volume at the critical failure state. The stability index takes the FS and corresponding sliding mass into consideration to assess the potential risk of slope failure in complex mountainous terrain. It is a valuable parameter for selecting a vulnerable area and evaluating the overall risk of slope failure.