• Journal of the Society of Naval Architects of Korea
• /
• v.45 no.1
• /
• pp.42-53
• /
• 2008

The two dimensional PIV (particle image velocimetry) measurement technique is applied to water flow in a narrow cavitation tunnel. The nearly homogeneous and isotropic turbulent flows are generated by the honeycomb installed in the tunnel and visualized with a PIV technique. The velocities in the measurement plane at the tunnel centerline 184cm downward from the honeycomb were measured and calculated by an image correlation technique. The turbulent properties are evaluated and each term in the turbulent kinetic energy equation is calculated for the conditions with different internal pressures. Lowering the internal pressure gives an effect on the turbulent flow due to growing bubbles which are resolved in the water. The turbulent kinetic energy in the measurement plane is decayed much slower than those of other research results carried out with wind tunnels. With decreasing the tunnel internal pressures the turbulent intensities are increased about 1.5 times and the anisotropic tendency is also increased.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.24 no.11
• /
• pp.1417-1427
• /
• 2000

A flow stabilizer, which is made of a honeycomb and three different mesh screens, is located downstream of a butterfly-type valve, for the reduction of flow disturbances behind the valve. Mean flow and turbulence measurements as well as flow visualizations are conducted in the downstream region of the deepens the non-uniformity of the streamwise velocity component and turbulence. The mesh screens considerably reduce the turbulence and enhance the uniformity of mean velocities. The combination of the honeycomb and the three mesh screens results in an efficient reduction in the flow disturbances. In addition, the flow stabilizer proves to have a good performance in the suppression of turbulence at a short distance.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.10
• /
• pp.2724-2737
• /
• 1994

The swirl effect on an axisymmetric turbulence has been investigated along its centerline by the hot wire anemometry. Flow facility to generate and conrol the swirl has been built by using the rotating honeycomb and grid. For the case of internal flows, as the strength of the swirl increases the flow tends to be locally isotropic by modifying the radial and the rotational components mainly. In comparison with those of the plain free jet, the decay of the centerline turbulences seems to be delayed substantially even with a slight swirl component.

• Proceedings of the KSR Conference
• /
• 2008.06a
• /
• pp.1781-1788
• /
• 2008

This report is the result of a basic experiment done on a mock-up tunnel, of what happens to the ventilated flow and fire driven flow inside a railway tunnel as the current inside the tunnel changes when an anti-smoke or a radio frequency invert control is installed. The duct used in this experiment is 10m in length, 0.5m in height and 0.25m in width and made of acrylic. An anti-smoke system with a motor that can produce current of 10m/sec maximum in order to create ventilated flow, has been installed. A honeycomb has been installed at the entrance of the duct to create a current flow that exists in tunnels. In order to create a ventilated flow, a current of 4m/s, 6m/s and 8m/s were generated using the anti-smoke system, as the study of current developed. A Hot-wire(TSI) and Pressure sensor(ENDEVCO) was installed in the duct, 1m apart, as the measurement of current and pressure went on. The current and pressure were automatically measured through the Lap View program and PC; the current flow in the mock-up tunnel generated by the honeycomb has been analyzed the pressure distribution and pressure drop has been analyzed.

• Fire Science and Engineering
• /
• v.33 no.4
• /
• pp.35-40
• /
• 2019

In this study, the mass flow rate of the heat release rate equation, which is the major factor of the oxygen consumption method, was analyzed for the fundamental investigation of the cone-calorimeter (5 m length and 0.3 m diameter). The shapes of a completely empty inside, 3 mm pore diameter mesh and pore diameter 10 mm honeycomb with 0.76 porosity were constructed using the cone-calorimeter. To calculate the mass flow rate, four bi-directional probes and thermocouples were installed in a uniform position in the vertical direction of flow. The velocity gradient and flow perturbation were measured from the increase in Reynolds number. As the flow capacity increased, the speed gradient increased in all three shapes relative to the turbulence intensity. In addition, the deviation of extended uncertainty to the mass flow was completely low in the order of empty space, mesh (d_p = 3 mm) and honeycomb (d_p = 10 mm and 𝜖 = 0.76) at the 95% confidence level. The results can be used in designs to improve the flow stability of the cone calorimeter.