• 한국생산제조학회지
• /
• 제7권4호
• /
• pp.56-63
• /
• 1998

The purpose of this is to analyze experimentally how the change of cutting speed have effects on hole over size of cutting hole, surface roughness of workpiece and roundness during the deep hole machining of SM55C with solid BTA drill using BTA drilling system. Conclusion reached is as follows. (1) The diameter was expanded for 25$\mu$m at the first section and then was reduced 0$\mu$m and 15$\mu$m respectively at the 10m and 20m section comparing to the diameter of tool with respect to the variation of cutting length at 70m/min of cutting speed. 0.15mm/rev of feed. (2) It was proved that roughness was below 8.67$\mu$m for the whole section of cutting length. (3) The roundness has been below 12$\mu$m. Regarding the polygon phenomenon, it has been proved that not only uneven best at 70m/min of cutting speed. 0.15mm/rev of feed.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1997년도 추계학술대회 논문집
• /
• pp.177-182
• /
• 1997

The purpose of this study is to analyze how tools, guide bush type and the change of cutting speed have effects on the diameter of cutting hole, surface roughness of workpiece and roundness during the deep hole machining of SM55C with solid BTA drill by using BTA drilling system through experiment. Conclusion reached is as follows. (1) The diameter was expanded for 25${\mu}{\textrm}{m}$ at the first section and then was reduced 0${\mu}{\textrm}{m}$ and 15${\mu}{\textrm}{m}$ respectively at the 10m and 20m section comparing to the diameter of tool with respect to the variation of cutting length. (2) It was proved that roughness was below 12S for the whole section of cutting length. (3) The roundness has been below 12${\mu}{\textrm}{m}$. Regarding the polygon phenomenon, it has bee proved that not only uneven number of angle but also even number (quadrilateral, elliptical) of angle were made. (4) Variation of diameter, surface roughness of workpiece and roundness turned out to ve the best at 70m/min of cutting speed, 0.15mm/rev of feed.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 춘계학술대회 논문집
• /
• pp.1068-1072
• /
• 1997

This work deals with on investigation the influence of various additives to a base stock cutting fluid in order to develop a better deep hold drilling. This investigation has been aiming at developing an oil which gives a maximum cutting efficiency at a minimum wear rate of the tool and the guiding pads. The purpose of study is to analyze how guide pad of tools, workpiece and the change of contained quantity of extreme pressure additive in cutting fluids have effects on the hold over size of cutting hole, surface roughness of workpiece,wear rates of guide pad and roundness during the deep hole machining of SM55C with solid BTA drill by using BTA drilling system through experiment. Conclusion reached is as follows. It has been proved that the contained quantity of surphur more affects machinability than that of extreme pressure additive of chlorine of cutting fluid in BTA drilling during Deep Hole Drilling. Considering its base oil, the the contained quantity of extreme pressure assitive of surphur can be different, but it's judged that the range of 1.5 ~ 2.0% is suitable to machinability for workpiece in BTA drilling. Regarding guide pad, it's judged that the reduction of wear is possible in propotion to the contained quantity of exrreme pressure additive of chlorine against supporting of cutting force and Bumishing operation of machining parts in cutting.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 춘계학술대회 논문집
• /
• pp.1063-1067
• /
• 1997

A study of carbide step drill cutting ability is highly progessing the step drill with more then twice diameter rate is so difficult in regrinding and very easy to damage during machining. As the machining of step drill for closed hole is occur to breakage at small diamter poistion, so it is very difficult to machinine. Thue, in this experiment, We investance roundness and surface roghness by machining distance and were identifid that the first distance, 5~10m, was fine with 7 .mu.m but the arround of 15m was happened so much alternation. And we were indentified that after 20m was happend statable machining. The surface roughness was happened the same conditions. So application of stwp drill we think that the selection of cutting conditions need lots consideration and the study of step drill's diameter ratio ratio is carred out.

• 소성∙가공
• /
• 제12권4호
• /
• pp.314-319
• /
• 2003

In the micro hole punching, the size and shape of burr and burnish zone are very important factors to evaluate quality of micro holes which depend on punch-die clearance, strain rate, workpiece material and etc. To get micro holes with small burr and wide burnish zone for industrial demands, not only the parametric study but also a study on fracture behavior in shear band are necessary. In this study, 100 $\mu$m, 25 $\mu$m micro holes in diameter were fabricated on brass (Cu63/Zn37) and SUS 316 foils as aspect ratio 1:1, and the characteristics of micro holes was investigated comparing with those of macro holes over several mm by scanning electron microscopic views and section views. Like macro hole, micro hole is also composed of 4 portions, rollover. burnish zone, fracture zone and burr, and it shows similar fracture behavior in shear band. But by high strain rate (10$^2$∼10$^3$s$^{-1}$ ) condition unlike that of macro hole fabrication and by the increment of relative grain size in the direction of the workpiece thickness, fracture zone is not observed.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2003년도 춘계학술대회논문집
• /
• pp.230-235
• /
• 2003

In the micro hole punching, the size and shape of burr and burnish zone are very important factors to evaluate quality of micro holes which depend on punch-die clearance, stain rate, workpiece material and etc. To get micro holes with small burr and wide burnish zone for industrial demands, not only the parametric study but also a study on fracture behavior in shear band are necessary. In this study, 100 $\mu\textrm{m}$, 25 $\mu\textrm{m}$ micro holes in diameter were fabricated on brass (Cu63/Zn37) and SUS 316 foils as aspect ratio 1:1, and the characteristics of micro holes was investigated comparing with man holes over several mm by scanning electron microscopic views and section views. Like macro hole, micro hole is also composed of 4 portions, rollover, burnish zone, fracture zone and it shows similar fracture behavior in shear band, but？ by high strain rate (10$^2$∼ 10$^3$s$\^$-1/) unlike macro hole fabrication and increment of relative grain size several different results are shown.

• 한국추진공학회지
• /
• 제5권1호
• /
• pp.42-48
• /
• 2001

지난 20년 동안 인장하중과 굽힘 하중 상태에서 복합재료 적층판의 크기효과에 관한 많은 연구가 수행되었으며, 시편의 크기를 증가함에 따라 복합재 적층판의 강도가 저하되는 경향은 잘 알려져 있다. 그러나, 복합재 압축시험의 어려움으로 인해 압축하중 상태에서 시편의 파괴강도에 대한 크기효과에 관한 연구는 거의 수행되지 않았다. 본 연구에서는 홀을 갖는 복합재의 압축 강도에 대한 크기 효과를 고찰하기 위해 T300/924C, $>[45/-45/0/90]_{3S}$를 사용하였으며, 시편의 크기 변화를 위해 2차원면적 변화(시편의 폭 및 길이 변화)를 고려하는 평면 스케일링 방법을 사용하였다. 실험 결과는 유한폭을 가지는 평판에 대한 명확한 홀 크기 효과를 보였을 뿐만 아니라, 같은 a/W(홀 직경/시편 폭)를 갖는 시편에서도 크기 효과를 확인할 수 있었다. 반면에, 홀이 없는 시편은 명확한 강도 크기 효과를 보이지 않았다.

• Journal of Biosystems Engineering
• /
• 제35권5호
• /
• pp.336-342
• /
• 2010

This study was performed to develop extrusion pelletizer for pelletizing the compost waste food. The effect of water content on the shape of pellet, the relationship between diameter of pellet and of extrusion hole and the relationship between extrusion force and die angle were investigated. Considering the stable shape of compost pellet and the operation efficiency of pelletizer, the water content of 2~4% was considered as the best condition. And the compost pellet could not maintain it's shape at the water content of 10% or over. The strongest extrusion force was needs when the die angle had $90^{\circ}C$ in 6 mm extrusion hole diameter, on the other hand, the weakest extrusion force was need at the die angle of $45^{\circ}{\sim}65^{\circ}$. The compression strength of pellet shows the highest strength of 9.2Mpa when we make the compost pellet after screening the compost and make it with a size of 1.18 mm(No.16) or less.

• 기술사
• /
• 제14권3호
• /
• pp.9-21
• /
• 1981

The rationalization for Tunnel Drifting is based on the high productivity which is achievable due to Continuous work with a Jumbo Drill, resulting in a much higher efficiency them the Conventional method of blasting, mucking and supporting services. Large projects of over 4,000m Tunnel Drifting are condidated to justify the use of a Jumbo Drill with a combination of superior explosives, machinery and techniques. During a Tunnel Drifting test, Gulita, Nabit and slurry made by Nitro Nobel were employed with following results. 1, Conditions: a. Granite Rock with Two free face b. Burden (W), 2m c. Diameter of hole, 42mm d. Depth of hole 3.5m e. Hole pitch 0.6m f. Charged Explosive per hole Gelatin Dynamite 4 pieces (112.5${\times}$4ea)+Guuita 5 pieces(110g${\times}$5ea) g. Simal-taneous Detonation h. After the blasting resultant rock size was Less 40% of the 0.3m Lumps. 2. Calculation results W=q/Wn=100cm‥‥‥Burden in simultaneous blasting 0.865kg(7.7ea)/hole ‥‥‥Amount of charge but hole pitch is 1.5W-2W The estimated cost of using a Jumbo Drill for the Construction of a 3,000,000 bbL sub-surface oil storage would be as follows: This calculation is based on the Jumbo Drill advancing 3.6m per blasting cycle. Unit cost/bbL Excavation $3.13 The attached sheet shows ideal Drilling pattern with Burn Cut & Smooth blasting method. In conclusion, it is my opinion that this method will assure safety and save cost and improve our technical know-how.

• 한국농공학회지
• /
• 제17권4호
• /
• pp.3991-4000
• /
• 1975

It is the aim of this study to investigate the influence of the factors in the sprayer nozzle for the travelling distance and to get nozzle design data in relation to the nozz1e with and without swirl plate. The factors of sprayer nozzle are composed of the spraying pressure, the helical angle of swirl plate, the helical groove depth of swirl plate, the distance of vortex chamber the slope of nozz1e cap, the curvature of nozzle cap and the hole diameter of nozz1e cap. The travelling distance and the size of sprayed particle are experimeted indoors by the factorial arrange-ment according to the 5 each level of the above factors. The results of this stupy are summarized as follows; 1. In the nozzle with swirl p1ate there were remarkable significance among factors each other, while without swirl plate were no significance. 2. The helical angle and groove depth in the nozzle with swirl plate were the highest effective factors. The effect of helical angle was very remarked in the quadratic curve with minium value. 3. The correlation betweenthe travelling distance and the sprayed particle size was no high and under 250 micron in the case with swirl plate, and there was higher correlation in the case without swirl plate. 4. The new ideal development of the swirl plate using of the most effective helical angle and groove depth will probably show the possiblities to make effective travelling distance over 8 meters and more over and to make average particle diameter under 300 micron.