• 한국추진공학회지
• /
• 제9권2호
• /
• pp.32-39
• /
• 2005

액체 연료 로켓의 연료 공급 라인을 모사 한 시스템에 대해, PSD가 시스템의 응답에 미치는 영향을 살펴보았다. 주관의 유량 변화에 대한 주관 압력 변화의 비(시스템 응답)를 PSD 내의 기체 체적$((0\~2)\times10^{-3}m^3)$과 PSD 배플의 직경(5, 50, 115 mm)을 변화시키며 살펴보았다. PSD 내에 기체가 있을 경우, 시스템의 고유진동 주파수가 작아짐을 확인하였다. 그리고 기체의 체적이 클수록 시스템 고유진동 주파수가 작아졌으나, 그 변화는 그리 크지 않았다. 또한 PSD 내 기체량이 많은 경우, 주관 내 압력 및 유량 변화의 진폭이 많이 감소함을 확인할 수 있었다. PSD 배플의 직경이 작아질수록 시스템 고유 진동 주파수가 작아졌으나 그 변화는 작았다. 또한 PSD 배플의 저항이 클 때, PSD 내 압력은 주관의 압력 크기보다 작고, 지연된 파형이 관찰되었다.

• 에너지공학
• /
• 제11권2호
• /
• pp.90-98
• /
• 2002

본 연구는 선회유동과 연소인자가 9.4L인 터보과급 디젤엔진의 성능과 배기가스특성에 미치는 영향을 실험적으로 고찰하였다. 일반적으로 디젤엔진의 연소과정에서 선회유동은 분사되고 있는 연료와 흡칩공기의 혼합을 촉진시켜 줌으로써 엔진성능을 향상시키는데 매우 중요한 인자가 된다. 특히 터보과급 디젤엔진에서는 실린더내의 고온.고압가스로 인하여 연비와 NO$_{x}$ 농도는 서로 상반관계를 가지므로 적절한 용량의 과급기선정으로 흡.배기시스템, 분사시스템 및 연소실의 설계 등을 고려할 필요가 있다. 본 연구의 결과로서, 정상유동실험을 통하여 선회비가 증가함으로써 평균유량계수가 감소하고, 반면에 걸프 펙터가 증가함을 알 수 있었다. 또한 엔진실험을 통하여 흡기포트의 선회비 2.43, 분사시기 BTDC 13$^{\circ}$ CA, 압축비 16, 리앤트란트 5$^{\circ}$형 연소실, 노즐분공경 $\Phi$0.28*6 및 과급기 GT40(압축기 A/R 0.58, 터빈 A/R 1.19)의 적용인자가 최적의 성능 및 배기가스를 만족시킬 수 있었다.

• 한국소음진동공학회논문집
• /
• 제21권11호
• /
• pp.1059-1066
• /
• 2011

The micro-perforated panel absorber(MPPA) is one of promising noise control elements because of its applicability to extreme environments where general porous materials cannot be used. Since the MPPA is inherently non-porous sound absorber, it can be a good candidate of acoustic protection system of a space launcher. The overall sound pressure level inside payload fairings of commercial launch vehicles is so high(around 140 dB OASPL) that the conventional linear impedance model cannot be directly applied to the design of the acoustic protection systems. In this paper an acoustic impedance models of a micro-perforated panel absorber at high sound pressure environment were reviewed and the use of the impedance on the practical design of MPPAs was addressed. The variation of absorption characteristics of MPPA was discussed according to the design parameters, e.g., perforation ratio, the minute hole diameter, the thickness of MPP and the incident sound pressure level.

• 한국소음진동공학회논문집
• /
• 제22권12호
• /
• pp.1199-1205
• /
• 2012

An empirical acoustic impedance model of acoustic resonators with extended neck at a high sound pressure environment is proposed. The acoustic resonator with extended neck into its cavity is appropriate for the launcher fairing application because the length of neck does not increase the total height of the resonator. This enables one to design slim and light acoustic resonators for launch vehicles. The suggested acoustic impedance model considers the incident pressure and geometric variables(the neck length, the perforation ratio and the hole diameter) in terms of non-dimensional variables. Several acoustic resonators with extended neck are manufactured and their wall impedances are measured according to the pre-defined incident pressure levels. Effects of non-dimensional variables on the non-linear acoustic impedance are investigated so that a simple non-linear impedance model for the launcher fairing application can be proposed. It is demonstrated that the estimated acoustic resistance and acoustic length correction show reasonable agreement with the measured ones within the range of design parameters for launcher fairings.

• Steel and Composite Structures
• /
• 제11권2호
• /
• pp.131-147
• /
• 2011

The aim of this work is to provide some insights into the elasto-plastic behaviour of plate girder web square and rectangular panels with centred and eccentric holes under both compression and in-plane bending moment. The numerical study was validated comparing the numerical results obtained for one simple steel plate configuration with the corresponding experimental results, obtained at the University of Padova, observing the influence of the initial out-of-plane imperfections on the force vs. displacement relationship and ultimate strength. Once validated the numerical approach, the effect of bending moment on the stability of the plate is studied and some differences with respect to the uniform compression load case are shown. The influence of dimension and position of the hole, the plate aspect ratio and the steel grade on elasto-plastic behaviour is observed. Some indications regarding the critical slenderness (at which transition from elastic to plastic collapse occurs) are given for square and rectangular plates with symmetric and eccentric holes having small, medium and large diameter.

• 한국유체기계학회 논문집
• /
• 제19권5호
• /
• pp.28-34
• /
• 2016

Though a peristaltic pump is a crucial element in miniaturized drug delivery systems, it has some intrinsic disadvantages such as backflow and flow fluctuation. To overcome these limitation, we have developed valve-less peristaltic pump system including orifice and stagnation chamber. we measured flow rate to investigate the performance of rotary peristaltic pump with three rollers and an elastomeric tube pumping a viscous fluid. The flow fluctuations and the backflow happen as a result from the disengagement of the contact interaction between the rollers and the tubes. Stagnation chamber installed in front of orifice plate was composed of rubber tube and gas chamber. By changing orifice hole diameter with stagnation chamber flow rate and pressure in the tube was regulated. The obtained maximum reduction ratio of flow fluctuation is 96.79%.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2011년도 추계학술대회 논문집
• /
• pp.178-185
• /
• 2011

The micro-perforated panel absorber (MPPA) is one of promising noise control elements because of its applicability to extreme environments where general porous materials cannot be used. Since the MPPA is inherently non-porous sound absorber, it can be a good candidate of acoustic protection system of a space launcher. The overall sound pressure level inside payload fairings of commercial launch vehicles is so high (around 140 dB OASPL) that the conventional linear impedance model cannot be directly applied to the design of the acoustic protection systems. In this paper an acoustic impedance models of a micro-perforated panel absorber at high sound pressure environment were reviewed and the use of the impedance on the practical design of MPPAs was addressed. The variation of absorption characteristics of MPPA was discussed according to the design parameters, e.g., perforation ratio, the minute hole diameter, the thickness of MPP and the incident sound pressure level.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2017년도 제48회 춘계학술대회논문집
• /
• pp.949-952
• /
• 2017

본 논문에서는 충돌형 분사기를 이용하여 수직분사 실험을 진행하였으며, 기존의 단공 오리피스의 분사기와 비교하여 분무특성에 어떠한 변화가 있는지 실험적으로 연구하였다. 또한 동일 오리피스 길이 대 직경비(L/d = 5)를 갖는 분사기를 바탕으로 충돌각(60, 90, 120)의 변화에 따른 액체 분무특성을 파악하였다. Top view의 기준 방향으로 y 방향에서의 분열길이 결과를 보면, 충돌각이 증가할수록 분열길이가 전체적으로 감소함을 알 수 있었다. 반면에 충돌형 분사기를 side view 기준으로 보았을 때, x 방향에서의 분열길이는 이전 단공노즐에서의 분열길이보다 더욱 감소하였으며, 이는 단공노즐의 분사기보다 충돌형 분사기의 미립화 성능이 우수함을 의미한다.

• Smart Structures and Systems
• /
• 제20권6호
• /
• pp.739-757
• /
• 2017

The main goal of this study is to investigate the hysteretic behavior of polyurethane rubber springs in compression with and without precompression. The precompression is introduced to provide rigid force in the behavior, and thereby a precompressed rubber spring can be used for a restoring element. For the goal, this study prepares nine rubber springs for three suites which are all cylindrical in shape with a hole at the center. The rubber springs in each suite have different dimensions of diameter and length but have similar shape factors; thus, they are designed to have a similar compressive stiffness. Three rubber springs from the nine are tested with increasing compressive strain up to 30% strain to investigate the behavior of the rubber springs without precompression as well as the effect of the loading strain. The nine springs are compressed up to 30% strain with increasing precompressive strain from 0 to 20% at increments of 5%. The study analyzes the effective stiffness and damping ratio of the rubber springs with and without precompression, and the rigid force of the precompressed rubber springs is discussed. Finally, this study suggests a regression method to determine the minimum required precompression to eliminate residual strain after unloading.

• Earthquakes and Structures
• /
• 제17권1호
• /
• pp.49-61
• /
• 2019

A novel asymmetrical resistance friction damper (ARFD) was proposed in this study to be applied on a rocking column base. The damper comprises multiple steel plates and was fastened using high-strength bolts. The sliding surfaces can be switched into one another and can cause strength to be higher in the loading direction than in the unloading direction. By combining the asymmetrical resistance with the restoring resistance that is generated due to an axial load on the column, the rocking column base can develop a self-centering behavior and achieve high connection strength. Cyclic tests on the ARFD proved that the damper performs a stable asymmetrical hysteretic loop. The desired hysteretic behavior was achieved by tuning the bolt pretension force and the diameter of the round bolt hole. In this study, full-scale, flexural tests were conducted to evaluate the performance of the column base and to verify the analytical model. The results indicated that the column base exhibits a stable self-centering behavior up to a drift angle of 4%. The decompression moment and maximum strength reached 42% and 88% of the full plastic moment of the section, respectively, under a column axial force ratio of approximately 0.2. The strengths and self-centering capacity can be obtained by determining the bolt pretension force. The analytical model results revealed good agreement with the experimental results.