• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 춘계학술대회 논문집
• /
• pp.1068-1072
• /
• 1997

This work deals with on investigation the influence of various additives to a base stock cutting fluid in order to develop a better deep hold drilling. This investigation has been aiming at developing an oil which gives a maximum cutting efficiency at a minimum wear rate of the tool and the guiding pads. The purpose of study is to analyze how guide pad of tools, workpiece and the change of contained quantity of extreme pressure additive in cutting fluids have effects on the hold over size of cutting hole, surface roughness of workpiece,wear rates of guide pad and roundness during the deep hole machining of SM55C with solid BTA drill by using BTA drilling system through experiment. Conclusion reached is as follows. It has been proved that the contained quantity of surphur more affects machinability than that of extreme pressure additive of chlorine of cutting fluid in BTA drilling during Deep Hole Drilling. Considering its base oil, the the contained quantity of extreme pressure assitive of surphur can be different, but it's judged that the range of 1.5 ~ 2.0% is suitable to machinability for workpiece in BTA drilling. Regarding guide pad, it's judged that the reduction of wear is possible in propotion to the contained quantity of exrreme pressure additive of chlorine against supporting of cutting force and Bumishing operation of machining parts in cutting.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 추계학술대회논문집B
• /
• pp.14-21
• /
• 2001

An experimental study has been conducted to investigate the heat/mass transfer characteristics within a square film cooling hole with asymmetric inlet flow conditions. The asymmetric inlet flow condition is achieved by making distances between side walls of secondary flow duct and film cooling hole different; one side wall is $2D_h$ apart from the center of film cooling hole, while the other side wall is $1.5D_h$ apart from the center of film cooling hole. The heat/mass transfer experiments for this study have been performed using a naphthalene sublimation method and the flow field has been analyzed by numerical calculation using a commercial code. Swirl flow is generated at the inlet region and the heat/mass transfer pattern with the asymmetric inlet flow condition is changed significantly from that with the symmetric condition. At the exit region, the effect of mainstream on the inside hole flow is reduced with asymmetric condition. The average heat/mass transfer coefficient is higher than that with the symmetric condition due to the swirl flow generated by the asymmetric inlet condition.

• 한국축산시설환경학회지
• /
• 제8권2호
• /
• pp.73-78
• /
• 2002

The experiment was carried out to investigate the optimal air velocity for improving the ventilation efficiency of duct ventilation system used in Korean swine building. The results are followed ; In 2.2 m height of duct, the air velocity of hole was 5.0 m/s as the over level of recommendation. In different hole interval, the air velocity was various of 4.6${\sim}$11.6 m/s in narrow hole interval, 5.4${\sim}$10.9 m/s in broad hole interval. But the air velocity was 6.6${\sim}$7.7 m/s in duct system pierced hole with equal interval, and it was equal velocity in different parts of duct in this hole interval.

• 한국정밀공학회지
• /
• 제15권1호
• /
• pp.117-129
• /
• 1998

Micro-hole drilling (holes less than 0.5 mm in diameter with aspect ratio larger than 10) is recently having more attention in a wide spectrum of precision production industries. Alternative methods such as EDM. laser drilling, etc. can sometimes replace the mechanical micro-hole drilling but are not acceptable in PCB manufacture because of the inferior hole quality and accuracy. The major difficulties in micro-hole drilling are related to small signal to noise ratios, wandering motions of the inlet stage, high aspect ratios, high temperatures and so forth. Of all the difficulties. the most undesirable one is the increase of drilling force as the drill proceeds deeper into the hole. This is caused mainly from the chip effects. Peck-drilling is thus widely used for deep hole drilling despite that it suffers from low productivity. In the paper, a method of cutting force regulation is proposed to achieve continuous drilling. A PD and a sliding mode control algorithms were implemented through controlling the spindle rotating frequency. Experimental results show that the sliding mode control reduces the nominal cutting force and the variation of the cutting force better than the PD control. The advantages of the regulation, such as increase of drill life, fast stabilization of a wandering motion, and the precise positioning of the hole are verified in experiment.

• 한국정밀공학회지
• /
• 제17권9호
• /
• pp.181-188
• /
• 2000

This paper deals with an analysis of the compliance characteristic for effective peg-in-hole task using robot hand without inter-finger coupling. We first observe the fact that some of coupling stiffness elements cannot be planned arbitrary. next we classify the task of inserting a peg-in-a-hole into two contact styles between the peg and the hole. Then we analyze the conditions of the specified stiffness matrix in the operational space to successfully and more effectively achieve the give peg-in-hole task for each case. It is concluded that the location of compliance center on the peg and the coupling stiffness element existing between the translational and the rotational direction play important roles for successful peg-in-hole task. Simulation results are included to verify the feasibility of the analytic results.

• 한국초전도ㆍ저온공학회논문지
• /
• 제20권3호
• /
• pp.5-10
• /
• 2018

This study presents that various grain boundary junctions are prepared by controlling the seed orientation combined with an artificial hole in a melt process REBCO bulk superconductor. Large grain YBCO superconductors have been fabricated with various grain boundary junctions that the angle between the grain boundary and the <001> axis of Y123 crystal is $0^{\circ}$, $30^{\circ}$ and $45^{\circ}$, respectively. The presence of the artificial hole is beneficial for the formation of clean grain boundary junction and single peak trapped magnetic field profiles have been obtained. Artificial hole makes two growth fronts meet at a point on a periphery of the artificial hole. The presence of artificial hole is not likely to affect on the distribution of Y211 particles. The newly formed <110> facet lines are explained by the formation of new Y123/liquid interface with (010) crystallographic plane.

• 대한기계학회논문집B
• /
• 제26권7호
• /
• pp.937-944
• /
• 2002

An experimental study has been conducted to investigate the heat/mass transfer characteristics within a square film cooling hole with asymmetric inlet now condition. The asymmetric inlet now condition is achieved by making distances between side walls of the secondary now duct and the film cooling hole different; one side wall is $2D_h$ apart from the center of the film cooling hole, while the other side wall is $1.5D_h$ apart from the center of the film cooling hole. The heat/mass transfer experiments for this study have been performed using a naphthalene sublimation method and the now field has been analyzed by numerical calculation using a commercial code. Swirl now is generated at the inlet region and the heat/mass transfer pattem with the asymmetric inlet now condition is changed significantly from that with the symmetric condition. In the exit region, the effect of mainstream on the inside hole now is reduced with the asymmetric condition. The average heat/mass transfer coefficient is higher than that with the symmetric condition due to the swirl now generated by the asymmetric inlet condition.

• 대한기계학회논문집A
• /
• 제24권9호
• /
• pp.2167-2173
• /
• 2000

The HANARO (High-flux Advanced Neutron Application Reactor) has operated since 1995. The Cold Neutron(CN) hole was implanted in the reflector tank from the design stage. Before a vacuum chamber and a moderator cell for the cold neutron source are installed into the CN hole, it is necessary to measure the exact size of the inside diameter and thickness of the CN hole to prevent the interference problem. Due to inaccessibility and high radiation field in the CN hole, a mechanical measurement method is not permitted. The immersion ultrasonic technique is considered as the best method to measure the thickness and the diameter. The 4 axis manipulator of the 2 channel of a sensor module was fabricated. The transducer of 10 MHz results in 0.03 nun of resolution. The inside diameter and thickness for 550 points of the CN hole were measured using 2 channel ultrasonic sensors. The results showed that the thickness is in the range of 13-6.7 mm and inside diameter is in the range of o 156-165. These data will be a good reference in the design of a cold neutron source facility.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 추계학술대회
• /
• pp.1121-1126
• /
• 2003

Strength evaluation was carried out for the fillet and oil hole of crankshaft of medium speed diesel HiMSEN engine to verify initial concept design. Alternating torque obtained from torsional vibration analysis and radial force due to firing pressure were applied. It was assumed that the maximum alternating torque and radial force occur simultaneously. Weak points in view of fatigue are proceeding fillet and crank pin fillet area and the minimum normalized fatigue safety factor is 1.17 at crank pin fillet. The fatigue strength of the oil hole was evaluated to verify the effect of the surface roughness of the oil hole. As results, the specific level of the inner surface roughness and the polishing depth of the oil hole for sufficient fatigue strength was suggested. The maximum stress value and stress distribution at the inner surface of the oil hole can be easily estimated at initial design stage by the newly developed method.

• 한국연소학회지
• /
• 제8권3호
• /
• pp.15-23
• /
• 2003

Partial quenching structure of turbulent diffusion flames in a turbulent mixing layer is investigated by the method of flame hole dynamics in order to develop a prediction model for turbulent flame lift off. The essence of flame hole dynamics is derivation of the random walk mapping, from the flame-edge theory, which governs expansion or contraction of flame holes initially created by local quenching events. The numerical simulation for flame hole dynamics is carried out in two stages. First, a direct numerical simulation is performed for constant-density fuel-air channel mixing layer to obtain the turbulent flow and mixing fields, from which a time series of two dimensional scalar dissipation rate array is extracted at a fixed virtual flame surface horizontally extending from the end of split plate to the downstream. Then, the Lagrangian simulation of the flame hole random walk mapping projected to the scalar dissipation rate array yields temporally evolving turbulent extinction process and its statistics on partial quenching characteristics. The statistical results exhibit that the chance of partial quenching is strongly influenced by the crossover scalar dissipation rate while almost unaffected by the iteration number of the mapping that can be regarded as a flame-edge speed.