• 열처리공학회지
• /
• 제13권5호
• /
• pp.303-308
• /
• 2000

The ring gears of automobile parts are manufactured generally process chart of which is as follows : forging ${\rightarrow}$ annealing or normalizing ${\rightarrow}$ rough machining ${\rightarrow}$ hardening(Quenching-Tempering or carburizing process) ${\rightarrow}$ finish machining. Isothermal annealing process after forging is most effective in the side of improvment of machinability. On this study we selected two kinds of steel;SCM415, SCM435 of most universal and investigated microstructures to find out most suitable condition of heat treatment in proportion continuous cooling and isothermal annealing. As the cooling rate is $5^{\circ}C$ per minute in continuous cooling process, martensite and bainite are coexisted with ferrite and pearlite in SCM435 steel. If the cooling rate is slower than $5^{\circ}C$ per minute, microstructure were only ferrite and pearlite but formation of band structure can't be avoid. On the other hand, microstructure is only ferrite and pearlite regardless of cooling rate because carbon content of SCM415 steel is low. Moreover formation of band structure isn't exposed by faster cooling rate. Most optimal temperature of the isothermal annealing is from $650^{\circ}C$ to $680^{\circ}C$ in SCM435 steel. When holding time is 60 minute with $650^{\circ}C$, the identical ferrite and pearlite microstructures can be obtained.

• Composites Research
• /
• 제23권5호
• /
• pp.30-38
• /
• 2010

성형조건에 따른 GMT-Sheet를 관찰하여, 성형품 표면의 불량원인을 조사했다. 현미경 관찰 결과, GMT-Sheet 성형품의 표면에서 구정, 섬유돌출, 크랙, 섬유노출, 마이크로 웰드라인, 핀홀, 여파굴곡곡선 등의 결함을 발견했다. 이 결함들은 요철의 발생원인이고, 표면 광택에 영향을 주는 현상이다. 그리고 표면거칠기에 영향을 주는 요철의 가장 주요한 발생원인은 보압 냉각 과정에서 발생하는 모재의 수축이었다. 성형 시의 보압하중이 높을수록 GMT-Sheet 성형품 표면은 좋아졌다. 또한 서냉실험에서는 탈형온도가 낮을수록 성형품의 표면이 좋아졌다.

• Journal of Microbiology and Biotechnology
• /
• 제9권6호
• /
• pp.784-788
• /
• 1999

The effects of pH, moisture content, and the relative amount of a polymer sample on the biodegradation of degradable polymers in soil were studied using various polymer materials such as cellulose, poly-(butylene succinate-co-adipate) (SG) polycaprolactone (PCL), a blend of PCL and starch (PCL-starch), and a poly-lactic acid (PLA). As with other materials, the polymers degraded faster at a neutral pH than at either acidic or basic conditions. Moisture contents of 60 and 100% water holding capacity exhibited a similar biodegradability for various polymers, although the effects differed depending on the polymer. For synthetic polymers, biodegradation was faster at 60%, while the natural polymer (cellulose) degraded faster at 100%. Fungal hypae was observed at a 60% water holding capacity which may have affected the biodegradation of the polymers. A polymer amount of 0.25% to soil revealed the highest biodegradability among the ratios of 0.25, 0.5, and 1%. With a higher sample amount, the residual polymer could be recovered after the biodegradation test. It was confirmed that a test for general biodegradation condition can be applied to plastic biodegradation in soil.

• Journal of Biosystems Engineering
• /
• 제38권3호
• /
• pp.180-184
• /
• 2013

Purpose: This study explored the factors influencing heating value in the process of torrefaction of water hyacinth. Methods: Torrefaction was applied with three temperature settings (200, 300, $400^{\circ}C$) and three time settings (1, 2, 3 h) using small electric heaters (11.3L of holding volume). This study investigated the heating values with the washing process and process factors influenced the torrefaction. In addition, this study compared the heating values in washed and unwashed samples and suggested the optimal conditions for increasing heating value. Results: Torrefaction increased the heating value by 8.18 ~ 30.04%. Comparing heating values of each condition, the optimal temperature for torrefaction was $300^{\circ}C$ and holding time was 1 hour. The washing process increased the heating value by 19 ~ 27%. The heating value of the sample treated at $300^{\circ}C$ for three hours was 4310.80 kcal/kg, which was greater than the first class wood pellet of 4300 kcal/kg. Conclusions: This study proved that the torrefaction and washing process increased the heating value of water hyacinth. Therefore, water hyacinth is expected to be an eco-friendly biomass which substitutes for wood pellet.

• 소성∙가공
• /
• 제24권1호
• /
• pp.5-12
• /
• 2015

In the current study, fundamental deep drawing characteristics of Ti-6Al-4V alloy sheets were investigated to establish the effect of processing conditions on large size square deep drawn cups. To accomplish this study, FE-simulations (Abaqus) were performed to determine optimum blank size, friction coefficient, the gap between punch and die, etc. The simulated processing parameters were verified experimentally. Based on the FE-simulation results, deep drawing was performed with various blank holding loads and sample sizes. In order to improve the formability of Ti-6Al-4V sheet, various lubricant methods were evaluated. Tensile tests and thickness measurements were conducted on the formed sheets. Processing parameters including blank holding force, lubricants, and optimum blank size, were selected to achieve improved drawing quality. With the optimum processing condition, a $200mm{\times}200mm$ cup was deep drawn successfully.

• 소성∙가공
• /
• 제30권3호
• /
• pp.134-141
• /
• 2021

In order to improve excessive spring-back behavior as a result of the roll forming process using ultra high strength steel (UHSS) sheet, local softening in region of a partial area expected to be deformed on an initial blank is considered in this study. With SPFC1470 UHSS sheet with initial blank thickness of 1.20mm, the local softening is performed with the following conditions: temperatures of 500℃, 550℃, 600℃ and 650℃, and holding time of 20s, 40s, 80s and 160s. Mechanical properties, such as yield stress and tensile strength, as well as elongation, are evaluated through uniaxial tensile tests, while the microstructural characteristics as a result of local softening are also investigated using the heat-treated specimens. As a result, it is shown that the spring-back behavior of the roll-formed prototype was reduced about by 78.9%, when the local softening at about 500℃ was performed for 160s considering the practical manufacturing condition.

• 반도체디스플레이기술학회지
• /
• 제23권1호
• /
• pp.88-91
• /
• 2024

The europium doped yttrium oxide (Y₂O₃:Eu³⁺) thin film was formed on a Si substrate by the conventional spin-coating process followed by rapid thermal annealing (RTA) treatment. The spinning profiles such as rotation speed, acceleration and holding times were controlled during the spin-coating process for the best condition of the Y₂O₃:Eu³⁺ thin film. The RTA treatment was conducted for several temperature in order to crystallize the spin coated film. The Y₂O₃:Eu³⁺ thin film presented best performance in the conditions of 4000 rpm, 30 s and 10 s of rotation speed, acceleration time and holding time, respectively, at a fixed RTA temperature of 900 ℃.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• 제5권11호
• /
• pp.2160-2174
• /
• 2011

In this paper, a new technique for color reproduction based on color variation characteristics of digital camera under a dim light condition is proposed. Generally, photographers should adjust a camera exposure properly for obtaining an image with real color tone of subjects. Thus, in case of taking a picture under a dim light condition, the exposure time of a camera has to be relatively longer than the one under a bright light condition. Although images with real color tone of the subject are obtained, the images may get blurred due to the shaky hands of photographer holding the camera. In order to avoid the blur effect, an input image is captured from a camera set as a short exposure time under a dim light condition. Then we propose a method to reproduce color tone of the dim input image. To this end, color variation characteristics which represent color variations of a digital camera are first extracted by analyzing the Macbeth color checker images taken under various exposure values. Then, a color reproduction is performed by an estimation based on the color variation characteristics. Experimental results have shown that the proposed method has achieved better performance of color reproduction, compared with existing methods.

• 한국조경학회지
• /
• 제27권1호
• /
• pp.122-131
• /
• 1999

Indoor environments are usually less than optimal for the growth of ferns, especially in regards to the water condition. These studies were performed to investigate responses involved in causing growth of ferns and presume management plan against the water deficit under indoor conditions. The effect of air humidity and soil moisture on the ferns was examined in Adiantume raddianum and Selaginella kraussiana. Results of experiments are as follows; 1. Under a low humidity condition, having a 25-50% RH. ornamental value of ferns decreased much more than under a 90% RH. Under a low soil moisture, such as sand treatment, ornamental value of ferns also decreased. 2. Leaf chlorophyll content, water content and stomata situations increased as air humidity and soil moisture went up. 3. Even if air humidity and soil water were not enough for ferns growth, the extending of irrigation cycle was helpful. 4. Under extremely low air humidity conditions, some water management, namely, using water holding soil or extending of irrigation cycle was desirable. Other methods of increasing air humidity, including water instruments such as ornamental pools, waterfalls, or fountains, grouping plants together were also helpful. But spraying water on leaves increased injury to ferns growth because of excess evaporation from the leaves. Though these studies, we learn that ferns are susceptible to water condition such as air humidity, soil water and water management. If other environmental factos are maintained with optimal conditions, water condition plays an important role in ferns growth in indoor environments.

• International Journal of Contents
• /
• 제16권3호
• /
• pp.1-17
• /
• 2020

Human motion recognition is essential for user-centric services such as surveillance-based security, elderly condition monitoring, exercise tracking, daily calories expend analysis, etc. It is typically based on the movement data analysis such as the acceleration and angular velocity of a target user. The existing motion recognition studies are only intended to measure the basic information (e.g., user's stride, number of steps, speed) or to recognize single motion (e.g., sitting, running, walking). Thus, a new mechanism is required to identify the transition of single motions for assessing a user's consecutive motion more accurately as well as recognizing the user's body and surrounding situations arising from the motion. Thus, in this paper, we collect the human movement data through Android smartphones in real time for five targeting single motions and propose a mechanism to recognize a consecutive motion including transitions among various motions and an occurred situation, with the state transition model to check if a vulnerable (life-threatening) condition, especially for the elderly, has occurred or not. Through implementation and experiments, we demonstrate that the proposed mechanism recognizes a consecutive motion and a user's situation accurately and quickly. As a result of the recognition experiment about mix sequence likened to daily motion, the proposed adoptive weighting method showed 4% (Holding time=15 sec), 88% (30 sec), 6.5% (60 sec) improvements compared to static method.