• The Journal of the Acoustical Society of Korea
• /
• v.14 no.4
• /
• pp.100-108
• /
• 1995

This study is aimed to show that revised prediction method in road traffic noise after comparing prediction method of National Institute of Environmental Research with that of the Acoustical Society of Japan. For this purpose, prediction equation and caluation procedure of each case was programmized and data predicted by each method were compared with those measured in the 14 fields. The result show that data predicted by 14 fields. The result show that data predicted by the method proposed in this study were closer to the data measured in the fields than those predicted by National Institute of Environmental Research and the Acoustical Society of Japan in the surroundings of urban express way (include highway) and general traffic road where the vehicle speed is higher than 40km/h.

• International Journal of Highway Engineering
• /
• v.18 no.2
• /
• pp.103-110
• /
• 2016

PURPOSES: In this paper, the effectiveness of speed-maintained standardization in road geometry on environmental impact at a downward slope location, based on greenhouse gas (GHG) emission indicators, was studied. Specifically, the aim of this study was to ascertain whether speed-maintained standardization resulted in decreased $CO_2$ emissions as well as noise pollution, due to reduced vehicle speeds. METHODS : In this study, speed-maintained standardization in road geometry was proposed as a means to reduce vehicle speeds, with a view to reducing $CO_2$ emissions and noise pollution. This technique was applied at a downward slope location. The vehicle speeds, $CO_2$ emissions, and noise levels before and after application of speed-maintained standardization were compared. RESULTS: It was found that speed-maintained standardization was effective as a means to reduce speed, as well as $CO_2$ emissions and noise pollution. By applying speed-maintained standardization, it was confirmed that vehicle speeds were reduced consistently. As a result, $CO_2$ emissions and noise levels were decreased by 9% and 11%, respectively. CONCLUSIONS : This study confirmed that speed-maintained standardization in road geometry is effective in reducing vehicle speeds, $CO_2$ emissions, and noise levels. Moreover, there is further scope for the application of this method in the design of roads in urban and rural areas, as well as in the design of highways.

• Journal of KSNVE
• /
• v.8 no.1
• /
• pp.146-156
• /
• 1998

To mitigate excessive noise from highways, and high speed rail road, it is often necessary to construct a noise barrier. Absorptive barroer attenuation solution is obtained for the problem of diffration of a plane wave sound source by a semi-infinite plane. A finite region in the vicinity of the edge has an highly absorbing boundary condition ; the remaining portion of the half plane is rigid. The problem which is solved is a mathematical model for a hard barrier with an absorbing edge. If the wavelength of the sound is much smaller than the length scale associated with the barrier, the diffraction process is governed to all intents and purpose by the solution to a standard problem of diffraction by a semi-infinite hard plane with an absorbent edge. It is concluded that the absorbing material that comprises the edge need only be of the order of a wavelength long to have approximately the same effect, on the sound attenuation in the shadow side of the barrier. Traffic noise is composed of thousands of sources with varying frequency content. To simplify noise predictions when barriers are present, an effective frequency of 550Hz may be used to represent all vehicles. The wavelength of sound at f=550Hz for traffic noise is about 2 feet. According to the above conclusion, an absorptive highway noise barrier is only needed to cover to cover approximately a 2 foot length of absorbing material. It would be more economical to cover only the region in the immediate vicinity of the edge with highly sound obsorbent material.

• International Journal of Highway Engineering
• /
• v.15 no.6
• /
• pp.61-68
• /
• 2013

PURPOSES : The purpose of this study is to study the noise reducing effect of Micro Surfacing by comparing general asphalt, longitudinal tining and Slurry Seal. METHODS : This study measures vehicles' noise of each section by the NCPX method that can measure noise between the road surface and the tire at the field. Total sound pressure and sound pressure level by the 1/3 octave band frequency are calculated through the field data of each section. Total sound pressure level is compared by ANOVA test statistically. After ANOVA test, post-hoc test is conducted to know mean difference of surface type by Tukey. RESULTS : As the result of CPB analysis to confirm sound pressure levels by frequency, it was shown that sound pressure levels by frequency are totally similar except for those of frequency bands between 100Hz and 500Hz. The result of ANOVA test and post-hoc test, it was shown that sections of surface type have a difference. The result of Micro Surfacing was lower 2~5dB(A) than other surface type. CONCLUSIONS : It is found that the noise reduction performance of Micro Surfacing was better than other surface type.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2004.11a
• /
• pp.611-614
• /
• 2004

In this study, ambient vibration tests are carried out to replace the current bridge integrity assessment using controlled vehicle test, which requires the traffic control and may induce public complains. Ambient vibration tests and output-only modal identification can be very effective approach to evaluate the bridge integrity because the ambient vibration tests can be performed very easily without trafnc control. The bridges in test road of Jungbu Inland Highway were tested and the results are discussed here.

• Journal of Korean Society of Environmental Engineers
• /
• v.28 no.11
• /
• pp.1198-1206
• /
• 2006

We have carried out highway traffic noise prediction and measurement for 10 sites with representative road shapes and structures. A road traffic noise prediction model(NIER('99)) has been developed for environmental impact assessment in Korea. With the fitted regression analysis, the distribution ratio($R^2$) and Pearson correction coefficient(r) was 92.4% and 0.96 in $1^{st}$ floor, 38.7% and 0.66 in $3^{rd}$ floor, 42% and 0.65 in $5^{th}$ floor, 7.5% and 0.27 in $7^{th}$ floor, 28.4% and 0.53 in 10th floor, 35.6% and 0.60 in $13^{th}$ floor, 52.7% and 0.73 in $15^{th}$ floor, respectively. The measured values of the noise level except the 1st floor did not show a good agreement with the predicted noise level in the NIER('99) formula. Also, the NIER('99) formula demonstrated that the measured values weren't reasonably close to the predicted values, indicating the validity and adequacy of the predicted models with the fitted vs residual analysis in the 95% of confidence interval and 95% of predict interval. Using the equal variation on the basis of the residual vs fitted value, there was the significant difference for variation between $3^{rd}$ floor and $15^{th}$ floor except $1^{st}$ floor. The results suggested that the NIER('99) model obtained by the results according to the apartment floor must be improved and developed on the road traffic noise.

• International Journal of Highway Engineering
• /
• v.15 no.4
• /
• pp.31-42
• /
• 2013

PURPOSES : The purpose of this study is to eliminate the noise of the vehicle after measuring the friction noise obtained from the NCPX (Noble Close ProXimity) method. The pure friction noise between the tire and road pavement could be determined from filtering the compositeness of sound and the influence of the vehicle noise. METHODS: The noise magnitude could be determined by analyzing the sound pressure level (SPL) and sound power level (PWL) along with the noise frequency of a FFT (Fast Fourier Transform) analysis as well as CPB (Constant Percentage Bandwidth) analysis. RESULTS: When the test for measuring the friction noise originated somewhere between tire and road pavement is performed with NCPX method, it must be fulfilled by attaching the surface microphone near the tire. In this condition, the surface microphone can measure the friction noise occurred at between tire and pavement, the chassis noise from the engine and power transfer units, the fluctuating aerodynamic noise, and the turbulence noise directly affected to the surface microphone. By using the NCPX method, the noise occurred at the vehicle must be eliminated for measuring the friction noise between tire and pavement from the traffic noise. CONCLUSIONS: The vehicle's testing engine noise depends on the vehicle and road types. The effect of vehicle's engine noise is less than the friction noise occurred at between tire and pavement at less than 1% effect.

• Journal of KSNVE
• /
• v.7 no.3
• /
• pp.369-376
• /
• 1997

With recent progress of developing infrastructure, construction vibration from the sites and traffic vibration caused by high-speed rail, subway, and roads is becoming a hazardous factor for vibration environment. In order to predict the damages caused by the vibrations mentioned above the vibration sources, have to be distinguished between point vibration and line vibration. Once the character of the vibration source is determined vibration propagation phenomenon needs to be analyzed by using prediction formula, and compared to the limits authorized by the law. The main purpose of this thesis is to manage the efficient vibration by reflecting these finding in making a consrtuction plan. Therefore, Vibration Management System (VMS) was developed which can predict and analyze the extent of developed utilizing Geographic Information System (GIS) to build a database. This database contains the attribute and the location information of the sources for predicting the formula of explosive vibration and subway traffic vibration, the buildings, the surrounding area and measurement sites. VMS will be useful in the future for predicting the vibrations caused by pile drive, traffic vibrations such as high speed electric railway, highway and roads, and other explosive vibrations by supplementing and updating the database.

• International Journal of Highway Engineering
• /
• v.12 no.1
• /
• pp.29-37
• /
• 2010

Porous pavements can provide road users with beneficial characteristics such as skid resistance and surface water drainage under rainy condition, and they cause less tire-road noise than conventional hot mix asphalt(HMA) pavements. However, voids of porous pavements are easily clogged by road debris at early stages, which leads to frequent maintenance works. Therefore, this study focused on the way of minimizing void clogging in porous pavements. During mixture design, the quantity of coarse aggregate has been increased to form many straight void conduits (SVCs) in porous HMAs. These SVCs were found to be effective resisting the void clogging problems. Four different porous HMAs(19mm, 13mm, 10mm, and 8mm) were developed and placed on highway roads. Their performances were validated with field tests during the past four years.

• International Journal of Highway Engineering
• /
• v.19 no.4
• /
• pp.1-7
• /
• 2017

PURPOSES : This study aims to improve complex modeling of multivariable, nonlinear, and overdispersion data with an artificial neural network that has been a problem in the civil and transport sectors. METHODS: Deep learning, which is a technique employing artificial neural networks, was applied for developing a large bus fuel consumption model as a case study. Estimation characteristics and accuracy were compared with the results of conventional multiple regression modeling. RESULTS : The deep learning model remarkably improved estimation accuracy of regression modeling, from R-sq. 18.76% to 72.22%. In addition, it was very flexible in reflecting large variance and complex relationships between dependent and independent variables. CONCLUSIONS : Deep learning could be a new alternative that solves general problems inherent in conventional statistical methods and it is highly promising in planning and optimizing issues in the civil and transport sectors. Extended applications to other fields, such as pavement management, structure safety, operation of intelligent transport systems, and traffic noise estimation are highly recommended.