• 연구논문집
• /
• s.33
• /
• pp.167-174
• /
• 2003

Alloy 713LC was developed to improve the tensile strength and ductility by reducing the carbon content of Alloy 713C. As Alloy 713LC was designed to minimize the mechanical property change with process conditions, it is generally utilized in the parts which have thick and thin sections simultaneously. In the thick and the thin sections, quite different properties are required. Consequently it is essential to crucially control the local mechanical properties of a parts by optimizing the process condition and heat treatment. In this research, high temperature mechanical properties including creep-rupture and strain-control low cycle fatigue were investigated together with the microstructural variations with heat treatment. Failure mechanism was also analyzed by observing the fracture surface to correlate the variation of mechanical properties with the microstructural change.

• Elastomers and Composites
• /
• v.50 no.4
• /
• pp.245-250
• /
• 2015

Recycling of ethylene-propylene-diene terpolymer (EPDM) scrap was tried by blending with polypropylene (PP). EPDM scrap powder was prepared by shear pulverization process at high temperature, which may lead to selective chain scission induced by difference in the critical elastic coefficient. On the other hand, EPDM scrap powder was prepared by adding a selected reclaiming agent during shear pulverization process at high temperature. Terpene as a bonding agent was then introduced to improve adhesion property. PP, used as a matrix for manufacturing thermoplastic elastomer, was modified by the incorporation of dicumyl peroxide and maleic anhydride. The functionalized EPDM and modified PP were blended and cured dynamically at $190^{\circ}C$. The blend materials prepared in this study showed the comparable results to those of conventional TPE in terms of tensile and flow properties. Also, the odor component of recycled EPDM was analyzed using GC-MS.

• Transactions of Materials Processing
• /
• v.28 no.6
• /
• pp.361-367
• /
• 2019

Microstructure evolution and tensile properties of Al-8mass%Mg alloy casting billet by biaxial alternative forging were investigated in this study. An alternative forging system tailored in this study was used to allow continuous strain accumulations on the alloy workpiece. A finite element (FE) simulation results revealed that the strain was mainly concentrated in the core and that the shear bands developed into a form with an X shape in the cross-section of workpiece after the alternative forging using octangular rod shaped dies. With increasing the forging passes, it was observed that the Al-8mass%Mg alloy workpieces were significantly deformed, and cracks began to form and propagate on the both ends of the forged workpieces after five passes at room temperature. In as-forged microstructures taken by microscopes, twins, clustering of dislocations, and fine subgrains were found. Tensile strengths of the forged specimens showed significant increases depending on the number of forging passes, and a trade-off relationship was observed between the elongation and strength. At room temperature and 100℃ the workpieces showed similar behaviors in microstructural evolution and tensile properties depending on forging passes, while the increase range in strength was reduced at 200℃.

• Journal of Welding and Joining
• /
• v.11 no.4
• /
• pp.91-102
• /
• 1993

The plasma sprayed $Cr_3C_2$-NiCr coatings are widely used as wear-resistant and corrosion-resistant materials. The mechanical and wear properties of the plasma sprayed $Cr_3C_2$-NiCr coating on steel plate were examined in this study. The pore in the coatings could be classified into two types, the one is the intrinsic pore originated from the spraying powder, the other is the extrinsic pore formed during spraying. During the tensile adhesion test, the fracture occured at the interface of top coating and bond coating. It is though that the compressive residual stress increases with the increase of the top coating thickness. From the wear test, it was found that the wear rate increased with the increase of the sliding velocity regardless of the temperature. It is thought that the fracture toughness reduces with the increase of the sliding velocity at $30^{\circ}C$ and that the adhesion amount increases with the increase of the sliding velocity at $400^{\circ}C$ It is concluded that the wear mechanism at $30^{\circ}C$ is the fracture and pull-out of the carbide particles due to the fatigue on sliding surface, while the wear mechanism at $400^{\circ}C$ is the adhesion of the smeared layer formed during wear process.

• Journal of the Korean Society for Heat Treatment
• /
• v.29 no.4
• /
• pp.181-189
• /
• 2016

The variation in microstructure and mechanical properties during heat treatment was examined in a series of 0.27% C-1.0% Si-1.5% Mn steels with chromium contents in the range of 0 to 1.0 wt%. It was found that chromium decreased the martensite packet size through the austenite grain refinement and increased tensile strength in the as-quenched steel, about 70 MPa per 1.0 wt%. The 0.27% C-1.0% Si-1.5% Mn-1.0% Cr steel showed tensile strength of 1700 MPa in the as-quenched steel. The 0.27% C-1.0% Si-1.5% Mn-1.0% Cr steel revealed a full martensitic structure after air cooling from $900^{\circ}C$ to room temperature, showing air hardening characteristics. Tempering at $150^{\circ}C$ slightly decreased the tensile strength and increased elongation, which is in a good agreement with impact toughness result.

• Journal of the Korean Electrochemical Society
• /
• v.9 no.1
• /
• pp.29-33
• /
• 2006

A new porous separator based on poly(vinyl chloride) (PVC)/poly(vinylidene fluoride-co-hexafluoro-propylene) (P(VdF-co-HFP)/poly(methyl methacrylate) (PMMA) was prepared by a phase inversion method. To enhance mechanical property, the membrane was stretched uniaxially at high temperature. Tensile strength and ionic conductivity were measured for various draw ratios. The tensile strength and ionic conductivity were increased with increasing draw ratio. The tensile strength of the separator reached 52MPa after stretching to draw ratio of 5, and the ionic conductivity of the separator was increased from $1.9Xs10^{-4}S/cm\;to\;4.6X10^{-4}S/cm\;at\;25^{\circ}C$. The stretched separator immersed in liquid electrolyte was electrochemically stable up to 4.7 V. The cell based on the stretched separator was maintained at about 99% of the initial discharge capacity after 10th cycle operation at 0.2C rate.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.28 no.2
• /
• pp.126-130
• /
• 2015

In this study, some materials are organized and experimented with variables to obtain the optimum mix proportion for the mechanical property of halogen free flame resistance compound with varying addition of nano clay. Tensile strength, density and stiffness are tested in the room temperature. In this study, unlike existing layered structure, nano clay with tabular structure is used and sufficient stiffness, strength, thermal stability and gas block capability can be achieved with small amount of addition. Tensile strength and elongation test show high rupture strength only in specimens with compatibilizing agents while density test shows average measurement in all the specimens except T-9. It was confirmed that the measurement value according to the additives in compatibilizing agent or in nano clay of hardness test represents similarly.

• Journal of Welding and Joining
• /
• v.16 no.3
• /
• pp.157-166
• /
• 1998

Recently as environmental pollution caused by Pb has posed a serious threat to the global environment, the trend to regulate the usage of Pb in electronic industry is one the rise. Currently, the solder alloy with high Pb content, Sn-37%Pb, is utilized in the electronic assembly therefore, the objective of this study is to develop an alternative solder alloy for the existing Sn-37%Pb solder alloy. First thing, this work choosed Sn-5%Pb-1.5%Ag, Sn-5%Pb-1.5%Ag-x%Bi(x=1~5%) for candidate solder alloys, and examined their properties such as melting range, wettability, microhardness, tensile property, oxidation behavior and microstructure. Wettability was on the same level of Sn-37%Pb. Dissolution of Pb ion in Sn-5%Pb solder was 0.46ppm. This solder alloy revealed cellular dendrite microstructure $\beta$-Sn matrix, Pb-rich phase, Ag/Sn, and Cu/Sn Intermetallic compounds. The range of solidification temperature was within 3$0^{\circ}C$. Also these alloy displayed higher tensile strength and lower elongation than Sn-37%Pb. The resistance of oxidation in Sn-5%Pb-1.5%Ag solder alloy was superior to that of Sn-37%Pb solder alloy. But that of Sn-5%Pb-1.5%Ag-5%Bi solder alloy was equal to that of Sn-37%Pb solder alloy.

• The korean journal of orthodontics
• /
• v.22 no.3 s.38
• /
• pp.557-578
• /
• 1992

Heat treatment which removes internal stress enhances the mechanical properties of the orthodontic arch wire. The main purpose of this experiment was to investigate the effects of the heat treatment on the mechanical properties of the Elgiloy wire. The Elfiloy wire, 0.016' X 0.022' and 0.018' X 0.025', were heat treated in an electric oven for 5, 10 and 15 minutes at selected temperatures between 300 and $900^{\circ}C$. Tensile strength and load deflection rate were measured to reveal the changes of mechanical property at various conditions, and each specimen was observed under metallurgic microscope. Also to trace the precipitation material due to overheat treatment, a qualitative analysis was carried out with EDS system. It was found that heat treatment at a low temperature caused an increase in the tensile strength and bending resistance, and a maintenance in the fibrous in the tensile strength and bending resistance, and a maintenance in the fibrous structure of both sizes of wire. The changes observed in properties and appearance were probably due to the relief of internal stresses incurred in the metal during cold working. In both sizes of wire the tensile strength and the bending resistance continued to decrease at high temperature, and the fibrous structure continued to disappear then was not observed at $900^{\circ}C$. The carbide precipitation founded in grain boundary at $750^{\circ}C$ probably was other elements carbide (Ni, Co) except Cr. The grain growth was observed at $1100^{\circ}C$. Optimum heat treatment for the 0.016' X 0.022' Elgiloy wire was 10 minutes at $500^{\circ}C$, and for the 0.018' X 0.025' Elgiloy wire it was 5 to 15 minutes at $500^{\circ}C$.

• Textile Coloration and Finishing
• /
• v.29 no.4
• /
• pp.231-238
• /
• 2017

There are many kinds of elements and processes for the development of high quality bedding products like fiber, high-temperature heat treatment, dyeing process, tenter drying with softening agent and multiple final finishing. Especially we examined the mechanical characteristic properties of fabrics according to different yarn types. The critical physical properties of the yarn consisting the pile knitted fabrics were obtained for the development of the hi-grade bedding items. The material property and the exhaustion behaviour of the developed pile knitted fabrics composing of different yarns were measured and observed. The physical properties of the developed fabric were evaluated through the material property analysis of the yarn, the physical nature of the pile knitted fabrics and the data of the exhaustion performance; tensile strength, tensile elongation, tearing strength, cross section of yarn types, dyeing properties etc. And then high-class of bedding items were knitted using the double raschel machine to make the pile knitted fabrics.