• Corrosion Science and Technology
• /
• 제2권3호
• /
• pp.155-160
• /
• 2003

Plasma spraying technique was used to fabricate functionally graded coating (FGC) of NiCrAIY/YSZ 8wt%$Y_2O_3-ZrO_2$ on a Co-base superalloy (HAYNES 188) substrate. Six layers were coated on the substrate for building up compositionally graded architecture. Conventional thermal barrier coating (TBC) of NiCrAIY/SZ with sharp interface was also fabricated. As-coated FGC and TBC samples were exposed at the temperature of $1100^{\circ}C$ for 10, 50, 100 hours in air. Microstructural change of thermally exposed samples was examined. Pores and microcracks were formed in YSZ layer due to evolution of thermal internal stress at high temperature. The amount of pores and microcracks in YSZ layer were increased with increasing exposure time at high temperature. High temperature oxidation of coatings occurred mainly at the NiCrAIY/YSZ interface. In comparison with the case of TBC. the increased area of the NiCrAIY/YSZ interface in FGC is likely to attribute to forming the higher amount of oxides.

• 한국약용작물학회지
• /
• 제28권2호
• /
• pp.111-118
• /
• 2020

Background: Cnidium officinale is a medicinal crop sensitive to high temperature. It is necessary to develop environment control technology that can reduce environmental stresses such as high temperature. This study was conducted to develop technology for stable production of Cnidium officinale by reducing damage owing to high temperature by applying shading treatment of varying duration, and structure. Methods and Results: Black shading nets were used from May to September or November; shading structures such as pillar, flat roof, and tunnel type structures were installed. Environmental changes, rate of photosynthesis, and growth characteristics were investigated. The shading treatment reduced temperature by 3℃. The rate of photosynthesis and yield with shading treatment were higher by 134% and 127%, respectively, than those with full sunlight. The ratio of shading area ranged from 50% to 71% according to the type of shading structure. The effect of environmental control on growth varied depending on the type of shading structure. Conclusions: The shading treatment reduced damage owing to high temperature, shading rate of 55% - 75% was recorded between the period May - September, and the flat roof type shading structure was considered the most suitable among shading methods.

• Journal of Ecology and Environment
• /
• 제42권4호
• /
• pp.278-284
• /
• 2018

Plant functional traits have been shown to be useful to understand how and why ecosystems and their components vary across environmental heterogeneity or gradients. This study investigated how plant functional (leaf) traits vary according to an elevation-associated environmental gradient. Environmental gradients (mean annual temperature and precipitation) were quantified, and leaf traits (leaf area, specific leaf area, leaf nitrogen, leaf phosphorus, leaf carbon, and leaf C/N ratio) of the understory woody plant species Acer pseudosieboldianum were examined across an elevational gradient ranging from 600 to 1200 m in a Baegunsan Mountain in Gwangyang-si, Jeollanam-do, South Korea. The results showed that mean annual temperature and precipitation decreased and increased along with elevation, respectively. Leaf area of the plant species decreased slightly with increasing elevation, while specific leaf area did not differ significantly. Leaf nutrients (nitrogen, phosphorus, and carbon concentrations) were higher at high elevations, but leaf C/N ratio decreased with elevation.

• 한국초전도저온공학회:학술대회논문집
• /
• 한국초전도저온공학회 2000년도 KIASC Conference 2000 / 2000년도 학술대회 논문집
• /
• pp.22-25
• /
• 2000

To improve the performance of high temperature superconducting current leads, variable cross-sectional area is considered. The cross-sectional area is varied as a function of current density to fix the safety factor along lead length. New integration method is devised to find optimum cross-sectional area distribution. New design of current lead has low heat leak into cryostat and less material than constant cross-sectional area leads. Conduction cooled lead is considered. The developed method is applied to Bi2223 current leads sheathed Ag-Au alloy.

• 설비공학논문집
• /
• 제13권4호
• /
• pp.252-261
• /
• 2001

Room air flow and temperature distribution was numerically investigated where a PAC(personal air conditioning) system was installed. The calculated results were compared with those from experiments. The effects of the important operation parameters such as the air flow rate, velocity, and temperature at the diffuser on the thermal performance of the system were studied. The possibility of energy saving using the PAC system was verified from the results, It was shown that the warm air from the diffuser could not spread over the whole task area if the inlet temperature was too high.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 추계학술대회논문집B
• /
• pp.131-136
• /
• 2001

In this paper, a high-temperature superconductor(HTS) current lead operating in current sharing mode is described. The minimum heat dissipation and the optimum safety factor(cross-sectional area) is obtained analytically for partial current sharing HTS leads. It is assumed that the current lead is in conduction cooled state, and the sheath material is the alloy of silver and gold. The reduced cross-sectional area results partial current sharing state, and consequently reduces conduction heat transfer, but the Joule heat generation is increased. The optimized HTS current lead is different from the conventional copper leads. In the copper leads, the minimum heat dissipation is obtained for the zero gradient of temperature at warm end. However, the temperature gradient at warm end is not zero when the HTS lead operates at minimum dissipation state.

• Journal of Biosystems Engineering
• /
• 제37권2호
• /
• pp.75-81
• /
• 2012

Oyster mushroom farm which could not meet optimum temperature range yields non-uniform sized, low quality products. Thus, this study, utilizing STAR CCM+, one of the computational fluid dynamics (CFD) programs, analyzed the impact of air circulation and temperature distribution. Methods: After we visited numerous mushroom farms, we measured the temperature at the discharge ports of heaters, fan capacity, and the locations of the air circulators in the farms. According to the data, most mushroom growers installed the heaters near the entrance and discharge ports of the heaters at the third growing bed on the same height as the heaters in the entrance. The temperature at the discharge port of heater was $1,26^{\circ}C$, and the fan capacity was 4,500 $m^3$/hr. The air circulator was placed in the center of the mushroom farm 50cm above the ground, and its capacity of inlet port was 1,100 $m^3$/hr and discharge port 1,600 $m^3$/hr. The mushroom farm was insulated. Results: According to the analysis of the temperature distribution in the vertical plane of the entrance side, no air circulation causes the high temperature zone of 296~299K at the discharge port of the heater to take up 34% of area while the operation of air circulators causes it to occupy only 9%. This means that not using air circulators leads to a concentration of high temperature at the discharge port near the entrance. In addition, with the results of the analysis of the temperature distribution in the vertical planes of the center, no air circulation causes the temperature zone of 295~298K at the discharge port of the heater to take up 48% of area while the operation of air circulators causes it to occupy 80%. This shows that the high outlet port temperature disseminated to the center. Conclusions: After ninety minute operation of both heater and air circulator, the interior temperature became stabilized in the mushroom farm. Air circulation made the high temperature at the discharge port disseminate to the center and exit in the farm and equalize the temperature distribution.

• 한국조경학회지
• /
• 제31권3호
• /
• pp.74-82
• /
• 2003

Under the assumption that the temperature of one location is closely related to land use characteristics around that location, this study is carried out to assess the impact of urban land use patterns on air temperature. In order to investigate the relationship, GIS techniques and statistical analyses are utilized, after spatially connecting urban land use data in Seoul Metropolitan Area with atmospheric data observed at Automatic Weather Stations (AWS). The research method is as follows: (1) To find out important land use factors on temperature, simple linear regressions for a specific time period (pilot study) are conducted with urban land use characteristics, (2) To make a final model, multiple regressions are carried out with those factors and, (3) To verify that the final model could be appled to explain temperature variations beyond the period, the model is extensively used for 5 different time periods: 1999 as a whole; summer in 1999; 1998 as a whole; summer in 1998; August in 1998. The results of simple linear regression models in the pilot study show that transportation facilities and open space area are very influential on urban air temperature variations, which explain 66 and 61 percent of the variations, respectively. However, the other land use variables (residential, commercial, and mixed land use) are found to have weak or insignificant relationship to the air temperatures. Multiple linear regression with the two important variables in the pilot study is estimated, which shows that the model explains 75 percent of the variability in air temperatures with correct signs of regression coefficients. Thus, it is empirically shown that an increase in open space and a decrease in transportation facilities area can leads to the decrease in air temperature. After the final model is extensively applied to the 5 different time periods, the estimated models explain 68 ∼ 75 percent of the variations in the temperatures is significant regression coefficients for all explanatory variables. This result provides a possibility that one air temperature model for a specific time period could be a good model for other time periods near to the period. The important implications of this result to lessen high air temperature we: (1) to expand and to conserve open space and (2) to control transportation-related factors such as transportation facilities area, road pavement and traffic congestion.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2001년도 추계학술발표회 초록집
• /
• pp.68-68
• /
• 2001

Thin films of polycrystalline silicon (poly-Si) is a promising material for use in large-area electronic devices. Especially, the poly-Si can be used in high resolution and integrated active-matrix liquid-crystal displays (AMLCDs) and active matrix organic light-emitting diodes (AMOLEDs) because of its high mobility compared to hydrogenated _amorphous silicon (a-Si:H). A number of techniques have been proposed during the past several years to achieve poly-Si on large-area glass substrate. However, the conventional method for fabrication of poly-Si could not apply for glass instead of wafer or quartz substrate. Because the conventional method, low pressure chemical vapor deposition (LPCVD) has a high deposition temperature ($600^{\circ}C-1000^{\circ}C$) and solid phase crystallization (SPC) has a high annealing temperature ($600^{\circ}C-700^{\circ}C$). And also these are required time-consuming processes, which are too long to prevent the thermal damage of corning glass such as bending and fracture. The deposition of silicon thin films on low-cost foreign substrates has recently become a major objective in the search for processes having energy consumption and reaching a better cost evaluation. Hence, combining inexpensive deposition techniques with the growth of crystalline silicon seems to be a straightforward way of ensuring reduced production costs of large-area electronic devices. We have deposited crystalline poly-Si thin films on soda -lime glass and SiOz glass substrate as deposited by PVD at low substrate temperature using high power, magnetron sputtering method. The epitaxial orientation, microstructual characteristics and surface properties of the films were analyzed by TEM, XRD, and AFM. For the electrical characterization of these films, its properties were obtained from the Hall effect measurement by the Van der Pauw measurement.

• 대한지리학회지
• /
• 제49권1호
• /
• pp.32-44
• /
• 2014

본 연구에서는 중부지방의 1월 최저기온 분포 특성을 파악하고 철원의 극한 최저기온의 원인을 규명하고자 하였다. 이를 위해 중부지방 25개 관측소의 1991~2010년 1월 기온 분포 특성과 철원 기온과 춘천, 홍천, 봉화, 대관령, 원주, 제천 등 중부내륙 지역의 기온 차이를 기압배치형에 따라 분석하였다. 일평균기온과 평균 일최저기온은 철원과 해발고도가 높은 지역에서 낮게 나타나지만, $-15^{\circ}C$ 이하 일수와 같은 극한기온의 출현빈도는 철원에서 두드러졌다. 시베리아 고기압이 확장하거나 우리나라 북쪽에 이동성 고기압이 위치할 때 철원 기온이 비교지점에 비해 상대적으로 더 낮다. 이동성 고기압의 영향을 받을 때는 철원과 비교지점 간 기온 차이가 적거나, 봉화, 제천과 같은 분지의 기온이 더 낮다.