• Transactions of the Korean Society of Automotive Engineers
• /
• v.13 no.6
• /
• pp.7-12
• /
• 2005

In order to analyze the microscopic spray characteristics of free spray in ultra high pressure region, the droplets size and velocity of free spray injected under atmosphere condition were measured by PDPA. As injection pressure became ultra high pressure, the droplets size was decreased continuously due to the increase of mutual reaction between droplets and air. But the decreasing rate became moderate. The velocity was increased until 250 MPa, and then decreased over that of injection pressure. It was seemed that the droplet size was similar in range of $280\~350\;MPa$, but increased in 414 MPa, even though injection pressure was increased. The microscopic spray characteristics of free spray got worse in 414 MPa.

• Geomechanics and Engineering
• /
• v.31 no.6
• /
• pp.557-571
• /
• 2022

Landslides are often triggered by weak interlayers initiated in tailings dam foundations, and hazards gradually occur. This is serious for landslides in high tailings dams due to their high potential energy. Tailing samples with a fine-grained interlayer at a set dip angle were prepared. Consolidated undrained (CU) triaxial shear tests were carried out by using a high-pressure triaxial apparatus. The results were compared with the results under a low confining pressure. Four reasons were summarized for high tailings dams more prone to instability than low dams. The shear strength of the samples with dipping interlayers decreases with increasing dip angle. An obvious straight drop in the stress path after the peak occurs in samples with dipping interlayers at an angle of 60°. The effect of the interlayer on the mechanical behaviour of tailings is very sensitive, especially for the sample with a dipping interlayer at an angle of 60°. Shear slipping along the interlayer should be given more attention in tailings dams. Compared with the results under low confining pressure, the stress decreases continuously for the samples with dipping interlayers at large angles under high confining pressure. The positive pore pressure, which reduces the effective stress, occurred in tailings samples under high confining pressure. The residual strength of tailings under high confining pressure is smaller than that under low confining pressure. These factors increase the dam break risk and the disaster impact for high tailings dams.

• Journal of the Korean Society of Food Culture
• /
• v.23 no.6
• /
• pp.667-680
• /
• 2008

The moisture contained in conventionally extracted red crab shell samples was lower than than in samples extracted using high pressure. In contrast, ash content increased as the extraction time increased and displayed no significant variation in high pressure extraction. Extraction time was influential, with lower lightness (L-value) being obtained in samples extracted at high pressure as compared to traditional extraction. However, large variation in a- and b-values resulted from traditional extraction. For both traditional and high pressure extraction increases in pH, salinity and saccharide content were noted with increasing extraction time, but these parameters did not vary substantially in red crab shell extracted at high pressure. The mineral content in samples extracted by high pressure was higher than in traditionally extracted samples. The mineral content increased with time, with marginally higher contents of essential amino acids and flavor enhancing amino acids noted following high pressure extraction. The contents of the flavor enhancing amino acids increased from 30?60 min, thereafter decreasing. Assessment of consumer acceptance revealed that, while traditionally manufactured red crab sauce was popular, sauce manufactured using a 60 min high pressure extraction was preferred. Extending the high pressure extraction time to 75 min produced a less sensory acceptable product, due to higher mineral and protein levels.

• Speech Sciences
• /
• v.9 no.4
• /
• pp.105-110
• /
• 2002

This study compared nasalance in low pressure and high pressure consonants and high and low vowels. The subjects were 8 children with cleft palate ranging from 3 years 6 months to 8 years in age. The measurement were taken in terms of the nasalance scores associated with 20 different word stimuli (high consonants+high vowels, high consonants+low vowels, low consonants+high vowels, and low consonants+low vowels) for subjects. The nasalance scores may be affected by high consonants and vowels types, low vowels and consonants types.

• 한국연소학회:학술대회논문집
• /
• 2015.12a
• /
• pp.41-44
• /
• 2015

Experimental study was conducted to investigate the effect of ultra-high injection pressure on combustion and emission characteristics in a single-cylinder diesel engine. Electronically controlled ultra-high pressure fuel injection system consistently supplied the fuel of ultra-high pressure up to 250 MPa. Various injection pressures, 40 to 250 MPa, were applied and compared. A injector with eight identical nozzle holes which have diameter of $105{\mu}m$ was used. The results showed high potential to improve the nitrogen oxide (NOx) and particulate matter (PM) trade-off relationship with an ultra-high injection pressure and the exhaust gas recirculation (EGR).

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.53 no.3
• /
• pp.148-151
• /
• 2004

For turn on high pressure sodium vapor lamp, Starting Voltage is very important factor. This starting voltage supply to high pressure sodium vapor lamp as electric discharge lamp, Electric field is producted in electric discharge tube, So accelerative electron collide against vapor atom and second electron is generated, And rapidly the current flow to electric discharge tube. This starting voltage is high voltage and source for melting contact that relay is according as turn on/off high pressure sodium vapor lamp. Consequently, This paper propose that the prevention of melting contact in accordance relay of controller for turn on/off high pressure sodium vapor lamp.

• Journal of ILASS-Korea
• /
• v.7 no.4
• /
• pp.16-22
• /
• 2002

The characteristics of free spray with ultra injection pressure was analyzed to clear the limit pressure of diesel engine. To obtain final goal, ultra high pressure injection equipment was developed, spray patterns were visualized under various ultra injection pressures. Spray penetration and spray width, volume and entrained air mass were increased with the increase of injection pressure. Sauter mean diameter and injection durstion wert decreased. But over 3,000bar of ultra injection pressure region the rates of increase show almost similar and finally the reversed tendencies at 4,140bar.

• Journal of Korean Academy of Nursing
• /
• v.42 no.5
• /
• pp.730-737
• /
• 2012

Purpose: This study was done to identify the time interval to pressure ulcer and to determine the optimal time interval for position change depending on pressure ulcer risk in patients using foam mattress in intensive care units. Methods: The Braden scale score, occurrence of pressure ulcers and position change intervals were assessed with 56 patients admitted to an intensive care unit from April to November, 2011. The time to pressure ulcer occurrence by Braden scale risk group was analyzed with Kaplan-Meier survival analysis and log rank test. Then, the optimal time interval for position change was calculated with ROC curve. Results: The median time to pressure ulcer occurrence was 5 hours at mild or moderate risk, 3.5 hours at high risk and 3 hours at very high risk on the Braden scale. The optimal time interval for position change was 3 hours at mild and moderate risk, 2 hours at high and very high risk of Braden scale. Conclusion: When foam mattresses are used a slight extension of the time interval for position change can be considered for the patients with mild or moderate pressure ulcer risk but not for patients with high or very high pressure ulcer risk by Braden scale.

• International Journal of Automotive Technology
• /
• v.6 no.2
• /
• pp.125-131
• /
• 2005

This article reports the experimental and numerical results for free sprays under ultra-high injection pressure conditions to give us better understandings of spray characteristics and also to make clear a limit pressure condition in diesel sprays. The high pressure injection system developed in this work is devised to reach ultra-high pressure conditions in the range from 150 MPa to 355 MPa. The free spray injected from a single nozzle injector is visualized by the Schlieren technique and the high speed camera. In particular, it is found that the shock waves are present and propagated along the edge of spray in the downstream direction. The measured spray penetration length increases gradually with the injection pressure, but its increasing rate is decreased as the injection pressure increases. The Sauter mean diameter is also no longer augmented for the injection pressures higher than 300 MPa. In addition, the three­dimensional numerical simulations are conducted for comparing the measurements with the predictions based on two different breakup models. The TAB model results show better agreements with experimental data than the WAVE model under ultra-high injection pressure conductions. Moreover, the simulation results show that the gas-phase pressure increases substantially in the vicinity of the spray tip region. It supports the experimental observation that the shock waves are formed at the front of spray tip and are propagated downstream.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2002.10a
• /
• pp.69-74
• /
• 2002

This study is object to structural analysis of high pressure injection nozzle. The finite element model was developed to compute the stress, strain for high pressure injection nozzle. For structural analysis using result from FEM code. This structural analysis results, many variables such as internal pressure, boundary condition, constraint condition and load condition are considered.