• Korean Journal of Materials Research
• /
• v.15 no.2
• /
• pp.115-120
• /
• 2005

The aim of this research is to develop the TRIP aided high strength low carbon steels using reverse transformation process. The $4\~8\%$ Mn steel sheets were reversely transformed by slow heating to intercritical temperature region and furnace cooling to room temperature. The stability of retained austenite depends on the enrichment of carbon and manganese by diffusion during the reverse transformation. The amount of retained austenite formed after reversely transformed at $625^{\circ}C$ for 6 hrs was about $50\;vol.\%$ in the $8\%Mn$ steel. The change in volume fraction of retained austenite with a holding temperature was consistent with the changes in elongation and the strength-ductility combination. The maximum strength-ductility combination of 40,000 $MPa{\cdot}\%$ was obtained when the $8\%Mn$ steel reversely transformed at $625^{\circ}C$ for 12 hrs. However, it's property was significantly decreased at higher holding temperature of $675^{\circ}C$ resulting from the decrease of ductility.

• Korean Journal of Materials Research
• /
• v.14 no.2
• /
• pp.126-132
• /
• 2004

The high strength steel sheets has been widely used as the automobile parts to reduce the weight of a vehicle. The aim of this research is to develop the TRIP aided high strength low carbon steels using reverse transformation process. The 0.15C-4Mn and 0.15C-6.5Mn steel sheets were reversely transformed by slow heating to intercritical temperature region and air cooling to room temperature. The stability of retained austenite depends on the enrichment of carbon and manganese by diffusion during the reverse transformation. The amount of retained austenite formed after reversely transformed at $645^{\circ}C$ for 12 hrs. was about 46vol.% in hot rolled 0.lC-6.5Mn steel. The change in volume fraction of retained austenite with a holding temperature was consistent with the changes in elongation and the strength-ductility combination. The tendency of tensile strength to increase with increasing the holding temperature was due to the decrease of retained austenite after cooling from the higher temperature of $670 ^{\circ}C$. The maximum strength-ductility combination was about 4,250 kg/$\textrm{mm}^2$ㆍ% when the hot rolled 0.lC-6.5Mn steel was reversely transformed at $645^{\circ}C$ for 12 hrs.

• Journal of the Korean Society for Heat Treatment
• /
• v.4 no.4
• /
• pp.44-52
• /
• 1991

The effect of deformation temperature and manganes contents on the tensile properties of duplex stainless steels with the structure of both ferrite and austenite were investigate. For this investigation, Fe-19% Cr-5% Ni-4~8% Mn alloys were prepared. The result obtained from this experiment are summerized as follows. With decreasing deformation temperature, tensile strengths of duplex stainless steel increased. Elongation showd to be increased and then decreased after representing the highest value at specific temperature. Tensile properties of duplex stainless steel were controlled by TRIP behavior in this experimental range of austenite contents. Tensile strengths decreased with increasing Mn contents. With increasing Mn contents, elongation decreased in the high temperature region, but increased in the low temperature region. The peak temperature representing the maximum elongation were changed to low temperature and the width of peak appeared to be broaden with increasing Mn contents.

• Korean Journal of Materials Research
• /
• v.11 no.5
• /
• pp.431-437
• /
• 2001

This research was examined the effect of intercritical heat treatment on the mechanical Properties and retained austenite formation in 0.1C-6.5Mn steels for the development of a high strength high ductility steel. using of transformation induced plasticity due to retained austenite. The stability of retained austenite is very important for the good ductility and it depend on diffusion of carbon and manganese during reverse transformation. It is effective to heat treat at$ 645^{\circ}C$ in order to obtain over 30 vol.% of retained austenite. However, it is more desirable to heat treat at $620^{\circ}C$, considering the volume fraction and mechanical stability of retained austenite. The strength-elongation combination in cold rolled steel sheets after reverse transformed at $620^{\circ}C$ for 1hr was about 4000k9/mm7, but it decreased rapidly with increasing holding time at high temperature due to the decrease of ductility. The addition of 1.1%Si in 0.14C-6.5Mn TRIP steel does not improve the mechanical properties and retained austenite formation.

• Journal of the Society of Naval Architects of Korea
• /
• v.45 no.4
• /
• pp.426-431
• /
• 2008

The high-strength low-alloy(HSLA) steels have low carbon contents($0.05{\sim}0.25%$ C) in order to produce adequate formability and weldability, and they have manganese contents up to 1.7%. Small quantities of silicon, chromium, nickel, copper, aluminum, molybdenum are used in various combinations. The results contained in this paper can provide the valuable information on the development of $-40^{\circ}C$ low temperature HSLA. Furthermore, the present experimental data will provide important database for casting steel materials of the offshore structure.

• Korean Journal of Materials Research
• /
• v.31 no.9
• /
• pp.519-524
• /
• 2021

The impact properties of two austenitic Fe-23Mn-0.4C steels with different Al contents for cryogenic applications are investigated in this study. The 4Al steel consists mostly of austenite single-phase microstructure, while the 5Al steel exhibits a two-phase microstructure of austenite and delta-ferrite with coarse and elongated grains. Charpy impact test results reveal that the 5Al steel with duplex phases of austenite and delta-ferrite exhibits a ductile-to-brittle transition behavior, while the 4Al steel with only single-phase austenite has higher absorbed energy over 100 J at -196 ℃. The SEM fractographs of Charpy impact specimens show that the 4Al steel has a ductile dimple fracture regardless of test temperature, whereas the 5Al steel fractured at -100 ℃ and -196 ℃ exhibits a mixed fracture mode of both ductile and brittle fractures. Additionally, quasi-cleavage fracture caused by crack propagation of delta-ferrite phase is found in some regions of the brittle fracture surface of the 5Al steel. Based on these results, the delta-ferrite phase hardly has a significant effect on absorbed energy at room-temperature, but it significantly deteriorates low-temperature toughness by acting as the main site of the propagation of brittle cracks at cryogenic-temperatures.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.53-53
• /
• 2010

Car industry has required light-weight steels, but still with strong mechanical strength. To meet this requirement, a variety of researches on Fe-Al alloys have been performed. As Al is being added in a disordered manner, alloys become more ductile and show higher yield stress. At a certain concentration of Al, however, the Fe-Al alloy system falls in a second phase whose mechanical strength is worsened. To understand the microscopic role of Al, we investigate the stability and the elastic properties of various Fe-Al alloys using ab initio density functional theory. At agiven Al concentration, the equilibrium geometry is obtained among several disordered Fe-Al alloy structures by performing the geometry relaxation. The formation energies and elastic properties such as bulk moduli of the equilibrium structures are also computed as a function of Al concentration. We also investigate the effects of different elements such as Si and Mn. Fe-Si alloy systems exhibit unusual mechanical behaviors requiring further investigation to understand their physical origin. Especially, the microscopic role of Mn is investigated to find its physical origin of preventing the Fe-Al alloy system from forming an unfavorable second phase. The effect of manganese on mechanical properties of Fe-based alloys is also explored.

• Applied Microscopy
• /
• v.46 no.4
• /
• pp.238-243
• /
• 2016

Twinning-induced plasticity (TWIP) steels with the austenite structure containing high manganese exhibit both good strength and excellent formability. Such properties originate from crystallographic slip and mechanical twins produced when the austenite structure is under mechanical stress. There are 12 twin systems, referred to as twin variants, when slip is induced. These twin systems include twin planes and twin directions and play an important role in determining strength and ductility of the material by strongly influencing texture formation of the austenite structure. In the present study, twins produced in a high-Mn TWIP steel as a result of uniaxial tension were observed using a transmission electron microscope; a comparative analysis was performed through interaction energy calculations. Electron diffraction was used to determine the twin system with respect to the uniaxial tension direction in each grain. Both the Schmid factors and interacting energies required for the generation of twins were calculated and subsequently compared with experimental results. This approach demonstrated the possibility of predicting the deformation behavior of the material.