• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 2001년도 유체기계 연구개발 발표회 논문집
• /
• pp.475-481
• /
• 2001

Foil bearings have been successfully used for small high speed rotors, such as ACM(Air Cycle Machine), turbo charger, turbo compressor, high speed motor, etc. Recently advanced researches are concentrated on the high load capacity and the extreme temperature foil bearings to extend the application boundary. Some bearings are already adopted into cryogenic machines and micro gas turbines. In this paper, a foil journal bearing designed for high load capacity, which is under development, is introduced. The bearing is for the turbo refrigerator which has a rotor of 18${\~}$25 kgf rotating at 23,000${\~}$38,000 rpm. This application is well beyond conventional spectrum of foil bearings because the rotor is relatively heavy and the rotational speed is low. Therefore, the development is challenging. The foil bearing is a bump type, the size is 60mm in diameter and 50mm in length, the operating fluid is air and rotational speed is 26,000 rpm. In-house software was developed and used for bearing design. Tested maximum load capacity is 80kgf, 0.62 in terms of load capacity coefficient, and testing is being continued.

• Steel and Composite Structures
• /
• 제25권5호
• /
• pp.603-615
• /
• 2017

This experimental research presents the seismic performance of steel reinforced high-strength concrete (SRHC) short columns. Eleven SRHC column specimens were tested under simulated earthquake loading conditions, including six short column specimens and five normal column specimens. The parameters studied included the axial load level, stirrup details and shear span ratio. The failure modes, critical region length, energy dissipation capacity and deformation capacity, stiffness and strength degradation and shear displacement of SRHC short columns were analyzed in detail. The effects of the parameters on seismic performance were discussed. The test results showed that SRHC short columns exhibited shear-flexure failure characteristics. The critical region length of SRHC short columns could be taken as the whole column height, regardless of axial load level. In comparison to SRHC normal columns, SRHC short columns had weaker energy dissipation capacity and deformation capacity, and experienced faster stiffness degradation and strength degradation. The decrease in energy dissipation and deformation capacity due to the decreasing shear span ratio was more serious when the axial load level was higher. However, SRHC short columns confined by multiple stirrups might possess good seismic behavior with enough deformation capacity (ultimate drift ratio ${\geq}2.5%$), even though a relative large axial load ratio (= 0.38) and relative small structural steel ratio (= 3.58%) were used, and were suitable to be used in tall buildings in earthquake regions.

• 동력기계공학회지
• /
• 제16권4호
• /
• pp.60-65
• /
• 2012

This study was carried out to investigate the effect of reverse transformation on the damping capacity in high manganese austenitic stainless steel. ${\alpha}^{\prime}$-martensite was formed with the specific direction and surface relief by deformation. Over 95% of the austenite phase was transformed to deformation-induced ${\alpha}^{\prime}$-martensite by 70% cold rolling. Reverse transformation became rapid above an annealing temperature of $550^{\circ}C$, but there was no significant transformation above $700^{\circ}C$. In addition, with increasing annealing time at $700^{\circ}C$, reverse transformation was induced rapidly, but the transformation was almost completed at 10 min. Damping capacity was increased up to $700^{\circ}C$, and than unchanged with the increasing annealing temperature. Damping capacity increased steeply with an increasing reverse treatment time up to 10min, whereas there were no significant change with a treatment time of more than 10 min. Damping capacity increased with an increasing the reversed austenite and was strongly affected by reversed austenite.

• Journal of Electrical Engineering and Technology
• /
• 제13권1호
• /
• pp.476-484
• /
• 2018

The high capacity audio watermarking algorithms are facing a main challenge in satisfying the robustness against attacks especially on de-synchronization attacks. In this paper, a robust and a high capacity algorithm is proposed using segment selection, Stationary Wavelet Transform (SWT) and the Quantization Index Modulation (QIM) techniques along with new synchronization mechanism. The proposed algorithm provides enhanced trade-off between robustness, imperceptibility, and capacity. The achieved watermarking improves the reliability of the available watermarking methods and shows high robustness towards signal processing (manipulating) attacks especially the de-synchronization attacks such as cropping, jittering, and zero inserting attacks. For imperceptibility evaluation, high signal to noise ratio values of above 22 dB has been achieved. Also subjective test with volunteer listeners shows that the proposed method has high imperceptibility with Subjective Difference Grade (SDG) of 4.76. Meanwhile, high rational capacity up to 176.4 bps is also achieved.

• The Journal of Asian Finance, Economics and Business
• /
• 제8권3호
• /
• pp.1153-1162
• /
• 2021

The innovation of enterprises allowed firms to promote technological innovation as an important choice to improve sustainable competitiveness. This study aims to investigate the relationship between absorptive capacity and innovation performance of Chinese high-tech enterprises and focuses on the mediating role of innovation culture in high-tech enterprises. Data came from surveying high-tech enterprises in China, and the reliability analysis, factor analysis, and correlation analysis, path analysis (SEM) were analyzed using SPSS23, AMOS. The results show that intellectual capital composed of human capital, structural capital, and relational has a significant impact on acquisition performance; intellectual capital is composed of human capital; structural capital has a significant influence on innovation performance; and absorptive capital has a significant impact on innovation performance. In addition, innovative culture plays a partial mediating role between absorptive capacity and innovation performance. The findings of this study suggest that, to ensure the better absorption and operation of knowledge, high-tech enterprises can accumulate more knowledge, promote the transformation of knowledge into technology, and strengthen the capability of knowledge absorptive capacity, and at the same time, create an innovation culture atmosphere and encourage employees to develop new products to achieve enterprise goals in order to promote the improvement of innovation performance.

• 소음진동
• /
• 제9권4호
• /
• pp.720-729
• /
• 1999

Coventional methods for reducing vibration in engineering designs (i.e. by stifferning or detuning) may be undesirable in conditions where size or weight must be minimized, or where complex vibration spectra exist. Some alloys with a combination of high damping capacity and good mechanical properties can provide attractive techanical and economical solutions to problems involving seismic, shock and vibration isolation. Although several non ferrous damping alloys have been developed, none of those materials are applied in any industrial factor due largely to high production cost. To meet these requirement, we have developed a new Fe-Mn high damping alloy. In previous studies, we have reported that an Fe-17%Mn alloy exhibits the highest damping capacity(Specific Damping Capacity:SDC, 30%) among Fe-Mn binary system, and proposed that the boundaries of various types such as $\varepsilon$-martensite variant boundaries, stacking faults in $\varepsilon$-martensite, stacking faults in austenitic and ${\gamma}$$\gamma /\varepsilon$ interfaces give rise to a high damping capacity. The Fe-17%Mn alloy also has advantages of good mechanical properties(T.S. 70 kg/nm$^2$ and low cost over other damping alloys(1/4 times the cost of non-ferrous damping alloy). Thus, the Fe-17%Mn high damping alloy can be widely applied to household appliances, automobiles, industrial facilities and power plant components. In this paper, the overall properties of the Fe-17%Mn high damping alloy is introduced, and its applicability to containment spray pump in the power plant is discussed.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2008년도 춘계학술대회 논문집
• /
• pp.1374-1384
• /
• 2008

The Design manual for adjusting the capacity and LOS of facilities has been shared in urban railways and high-speed railway stations. However, the pattern of urban railways users and those of high-speed railway users are different from each other. For an example, the high-speed railway users tend to carry voluminous luggages and the transportation disadvantaged such as children and the elderlies. Accordingly, we see that the scale of facilities and the station itself should be constructed differently. The transfer facilities in the high-speed railway stations are classified widely into walking assisting facilities and convenient facilities. We invented the concept of PME(Pedestrian Moving Equivalent) and PWE(Pedestrian Waiting Equivalent)for the spatial calculation of those who are with wheeled luggages, back packs, and children to reflect the uniqueness of users in high-speed railway stations. These equivalents have been applied to the design of the facilities to asses the new Capacity and LOS that are users' favored.

• 현장농수산연구지
• /
• 제22권2호
• /
• pp.37-50
• /
• 2020

The purpose of this study is to identify professional development needs of Extension professionals and to evaluate competencies essential to be a successful Extension professional. For the purpose of this study, quantitative capacity data of extension professionals were collected from the survey instrument based on Extension Professional Evaluation Scale in Utah state university. Descriptive statistics, mean difference analysis, IPA(importance-performance analysis) analysis were used to analyze the data. The main results of the study are as follows. First, it is necessary to first reinforce education on specialized technical capacity among the three extension capacity areas. The current status of the professional capacity of extension professionals in the three areas was found to be at the average level, and the level of professional technical capacity was relatively low. In addition, the importance was evaluated that professional technology capacity is more important than the project development/evaluation capacity and communication capacity. Second, Second, in order to reinforce communication capacity, it is necessary to strengthen education on 'development of joint educational materials with colleagues'. Third, in order to reinforce project development/evaluation capacity, it is necessary to strengthen education on 'project planning'. In the IPA analysis results, the importance was high, but the capacity with relatively low performance were analyzed as 'project planning'. Fourth, in order to reinforce professional technical capacity, it is necessary to develop an education program for 'crop expertise' first. In the IPA analysis results, the importance was high, but the competencies with relatively low performance were analyzed as 'crop technology expertise'.

• 동력기계공학회지
• /
• 제9권1호
• /
• pp.70-75
• /
• 2005

The damping property of Fe-12Cr-22Mn-X alloys has been investigated to develop high damping and high strength alloy. Particularly, the effect of the phase of austenite, alpha and epsilon martensite, which constitute the structure of the alloys Fe-12Cr-22Mn-X alloys, on the damping capacity at room temperature has been investigated. Various fraction of these phases were formed depending on the alloy element and cold work degree. The damping capacity is strongly affected by ${\varepsilon}$ martensite while the other phase, such as ${\alpha}'$ martensite, actually exhibit little effect on damping capacity. In case of Fe-12Cr-22Mn-3Co alloy, the large volume fraction of ${\varepsilon}$ martensite formed at about 30% cold rolling, and in case of Fe-12Cr-22Mn-1Ti alloy, formed at about 20% cold rolling and showed the highest damping capacity. Damping capacity showed higher value in Fe-12Cr-22Mn-1Ti alloy than one in Fe-12Cr-22Mn-3Co alloy.

• 한국재료학회지
• /
• 제25권1호
• /
• pp.9-15
• /
• 2015

The effect of retained and reversed austenite on the damping capacity in high manganese stainless steel with two phases of martensite and austenite was studied. The two phase structure of martensite and retained austenite was obtained by deformation for various degrees of deformation, and a two phase structure of martensite and reverse austenite was obtained by reverse annealing treatment for various temperatures after 70 % cold rolling. With the increase in the degree of deformation, the retained austenite and damping capacity rapidly decreased, with an increase in the reverse annealing temperature, the reversed austenite and damping capacity rapidly increased. With the volume fraction of the retained and reverse austenite, the damping capacity increased rapidly. At same volume of retained and reversed austenite, the damping capacity of the reversed austenite was higher than the retained austenite. Thus, the damping capacity was affected greatly by the reversed austenite.