• Journal of the Korean Vacuum Society
• /
• 제16권2호
• /
• pp.79-90
• /
• 2007

Prototype of $800{\ell}$ vacuum web coater (Vic Mama) consisting of ion source with low energy less than 250 eV for high speed surface modification and 4 magnetron sputter cathodes was designed and constructed. Its performance was evaluated through fabricating the adhesiveless flexible copper clad laminate (FCCL). Pumping speed was monitored in both upper noncoating zone pumped down by 2 turbo pumps with 2000 l/sec pumping speed and lower surface modification and sputter zone vacuumed by turbo pumps with 450 1/sec and 1300 1/sec pumping speed respectively. Ion current density, plasma density, and uniformity of ion beam current were measured using Faraday cup and the distribution of magnetic field and erosion efficiency of sputter target were also investigated. With the irradiation of ion beams on polyimide (Kapton-E, $38{\mu}m$) at different fluences, the change of wetting angle of the deionized water to polyimide surface and those of surface chemical bonding were analyzed by wetting anglometer and x-ray photoelectron spectroscopy. After investigating the deposition rate of Ni-Cr tie layer and Cu layer was investigated with the variations of roll speed and input power to sputter cathode. FCCL fabricated by sputter and electrodeposition method and characterized in terms of the peel strength, thermal and chemical stability.

• Journal of the Korean Ceramic Society
• /
• 제51권4호
• /
• pp.271-277
• /
• 2014

To overcome the limitations of the solid oxide fuel cells (SOFCs) due to the high temperature operation, there has been increasing interest in proton conducting fuel cells (PCFCs) for reduction of the operating temperature to the intermediate temperature range. In present work, the perovskite $BaCe_{0.85-x}Zr_xY_{0.15}O_{3-\delta}$ (BCZY, x = 0.1, 0.3, 0.5, and 0.7) were synthesized via solid state reaction (SSR) and adopted as an electrolyte materials for PCFCs. Powder characteristics were examined using X-ray diffraction (XRD), thermogravimetric analysis (TGA) and Brunauer, Emmett and Teller (BET) surface area analysis. Single phase BCZY were obtained in all compositions, and chemical stability was improved with increasing Zr content. Anode-supported cell with $Ni-BaCe_{0.55}Z_{0.3}Y_{0.15}O_{3-\delta}$ (BCZY3) anode, BCZY3 electrolyte and BCZY3-$Ba_{0.5}Sr_{0.5}Co_{0.8}Fe_{0.2}O_{3-\delta}$ (BSCF) composite cathode was fabricated and electrochemically characterized. Open-circuit voltage (OCV) was 1.05 V, and peak power density of 370 ($mW/cm^2$) was achieved at $650^{\circ}C$.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 한국전기전자재료학회 2007년도 추계학술대회 논문집
• /
• pp.259-259
• /
• 2007

층상구조의 전이금속 산화물($LiMO_2$, M=Co, Ni, Mn)은 리튬이차전지용 양극재료로 활발한 연구가 진행되고 있다. 차세대 리튬이차전지 시스템의 개발 및 고성능화를 위해서는 전지의 용량을 결정하는 핵심 부품인 양극재료의 고용량화 및 고안정화는 필수 불가결하다. 따라서 본 연구에서는 상업적으로 큰 장점이 있는 고상반응 공정을 이용하여 리튬이차전지용 양극소재를 제조하고, 소재의 전기화학적, 구조적인 특성을 평가하였으며, 다음과 같은 주제를 가지고 연구를 진행하였다. $LiCoO_2$ 양극재료는 리튬이온전지로 널리 사용되고 있다. 높은 에너지 밀도의 리튬이온전지를 얻기 위해서는 $LiCoO_2$ 양극재료가 고용량화 및 고밀도화를 가져야 한다. 여기서 $LiCoO_2$ 분말이 irregular particle morphology를 가지면 tap density가 $2.2-2.4gcm^{-3}$로 에너지 밀도가 낮으나, 구형 $LiCoO_2$의 정극재료는 tap density가 $2.6-2.8gcm^{-3}$로 상대적으로 energy density가 높아지는 효과가 있다. 구형 $LiCoO_2$ 양극재료를 합성하기 위해서는 chelating agent를 이용한 "controlled crystallization" 침전법을 사용하여 합성한 구형 코발트 수화물을 사용하고 있다. "controlled crystallization" 침전법에서 사용되는 chelating agent로는 주로 ammonia가 이용되고 있다. 본 연구에서는 chelating agent로 ethylene diamine을 사용하여 sodium hydroxides를 precipitation으로 침전 반응하여 구형 코발트 수화물을 합성하였다. 상기 방법으로 합성된 코발트 수화물과 리튬 수화물($LiOH{\cdot}H_2O$-고순도화학(高殉道化學))을 사용하여 고상법을 통하여 $LiCoO_2$를 합성하였다. 제조된 분말의 결정구조와 전기화학적 특성분석은 X-선 회절분석 및 리트벨트 구조정산, 그리고 충/방전 싸이클링을 수행하였으며, 분말의 미세구조 변화를 SEM을 이용하여 분석하였다.

• Journal of the Korean Ceramic Society
• /
• 제43권5호
• /
• pp.299-303
• /
• 2006

In this paper, anode supported SOFC with columnar structured YSZ electrolyte was fabricated via Electron Beam Physical Vapor Deposition (EBPVD) method. Liquid condensation process was employed for the preparation of NiO-YSZ substrate and the high power electron beam deposition method was used for the deposition of YSZ electrolyte film. Double layered cathode with LSM-YSZ and LSM was printed on electrolyte via screen-printing method and fired at $1150^{\circ}C$ in air atmosphere for 3 h. The electrochemical performance and the long-term stability of $5{\times}5cm^2$ single cell were investigated with DC current-voltage characteristics and AC-impedance spectroscopy. According to the investigation, $5{\times}5cm^2$ sized unit cell showed the maximum power density of around $0.76W/cm^2$ at $800^{\circ}C$ and maintained the stable performance over 400 h.

• Korean Chemical Engineering Research
• /
• 제46권1호
• /
• pp.131-136
• /
• 2008

Silica- or titania-filled poly (vinylidene fluoride-co-hexafluoropropylene)-based polymer electrolytes were prepared by phase inversion technique using N-methyl-2-pyrrolidone and dimethyl acetamide as solvent and water as non-solvent. The polymer electrolytes were adopted to the lithium metal polymer battery using high-capacity cathode $Li[Ni_{0.15}Co_{0.10}Li_{0.20}Mn_{0.55}]O_2$ and lithium metal anode. After the repeated charge-discharge test for the cell, it was proved that the cell adopting the polymer electrolyte based on the phase-inversion membrane containing 40~50 wt% silica showed the highest discharge capacity (180 mAh/g) until 80th cycle and then abrupt capacity fade was just followed. The capacity fade might be due to the deposition of lithium dendrite on the polymer electrolyte, in which the capacity retention was no longer sustainable.

• Resources Recycling
• /
• 제28권5호
• /
• pp.60-67
• /
• 2019

A valuable metal recovery from waste resources such as spent rechargeable secondary batteries is of critical issues because of a sharp increase in the amount of waste resources. In this context, it is necessary to research not only recycling waste lithium-ion batteries (LIBs), but also reusing valuable metals (e.g., Li, Co, Ni, Mn etc.) recovered from waste LIBs. In particular, the lithium hydroxide ($LiOH{\cdot}xH_2O$), which is of precursors that can be prepared by the recovery of Li in waste LIBs, can be reused as a catalyst, a carbon dioxide absorbent, and again as a precursor for cathode materials of LIB. However, most studies of recycling the waste LIBs have been focused on the preparation of lithium carbonate with a recovery of Li. Herein, we show the preparation of high purity lithium hydroxide powder along with the precipitation process, and the systematic study to find an optimum condition is also carried out. The lithium carbonate, which is recovered from waste LIBs, was used as starting materials for synthesis of lithium hydroxide. The optimum precipitation conditions for the preparation of LiOH were found as follows: based on stirring, reaction temperature $90^{\circ}C$, reaction time 3 hr, precursor ratio 1:1. To synthesize uniform and high purity lithium hydroxide, 2-step precipitation process was additionally performed, and consequently, high purity $LiOH{\cdot}xH_2O$ powder was obtained.