• 비파괴검사학회지
• /
• 제33권5호
• /
• pp.415-421
• /
• 2013

CGI는 주철보다 큰 강도 또는 작은 무게가 요구되는 응용에서 인기를 얻고 있다. 최근, 강화흑연강은 디젤 엔진 블록, 터보 하우징 및 배기 매니폴드에 사용된다. 이 논문은 873~1173 K에서 1~24 시간 동안 열화된 CGI340의 기계적 성질의 변화에 따른 음향방출 특성을 평가하였다. 연필심 파괴시험 결과에서, 탁월주파수 및 모재의 속도는 각각 97 kHz와 5,490 m/s이었다. 인장시험에서 모재는 상대적으로 높은 탁월주파수를 얻었다. 그러나 열처리된 재료, 열처리 시간이 길고, 열처리 온도가 높을수록, 낮은 주파수의 영역에서 얻어졌다. 이러한 현상은 장기간의 사용에 의해 나타난다.

• 대한치과보철학회지
• /
• 제28권1호
• /
• pp.25-41
• /
• 1990

The purpose of this study was to evaluate and compare the dimensional changes of relined dentures with a light-curing resin, a heat-curing resin, and a direct, hard reline resin. And also to measure the transverse strength, impact strength, surface hardness of the three resins used in relining. The surface textures of three resins also of evaluated by using scanning electron microscope. Through analyses on the data from this study, the following conclusions were obtained. 1. Impact strength of heat-curing resin was highest, and direct, hard reline resin higher, light-curing resin lowest. 2. Transverse strength of heat-curing resin was highest, and direct, hard reline resin and light-curing resin was lower and not signiicantly different. 3. Surface hardness of light-curing resin was lighest, heat-curing resin higher, and direct, hard reline resin was lowest. 4. After storage of the relined dentures for 1 day and 1 week in water at room temperature, linear shrinkage of distance between the reference points in the maxillary base relined with direct, hard reline resin was lowest, and those relined with light-curing resin and heat-curing resin were lower and were not significantly different. 5. After storage for 4 weeks in orator at room tempeature, linear shrinkage of distance between ridge crests of dentures relined with heat-curing resin was highest and that of distance between denture borders was not significantly different. 6. The dimensional changes of relined dentures during storage in water was not significant except those of distance between denture borders relined with light-curing resin at 1 day and 1 week storage in water. 7. At low magnification (x40) of SEM examination, the surface textures of three resins were similar except light-curing resin which had some defects. At high magnification (x200), the surface textures of hard, direct reline resin were smooth with little defects, but those of heat-curing resin and light-curing resin w ere irregular.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집A
• /
• pp.223-230
• /
• 2001

The Monkman-Grant (M-G) and its modified parameters were estimated for modified type 316LN and $9{\sim}12Cr-1Mo$ steels with chemical variations. Several sets of creep data were obtained by constant-load creep tests in $550-650^{\circ}C$ ranges. The relation parameters, m, $m^*$, C and $C^*$ were proposed and discussed for two alloy systems. In creep fracture mode, type 316LN steel showed domination of the intergranular fracture caused by growth and coalescence of cavities. On the other hand, the Cr-Mo steel showed transgranular fracture of the ductile type caused from softening at high temperature. In spite of the basic differences in creep fracture modes as well as creep properties, the M-G and its modified relations demonstrated linearity within the $2{\sigma}$ standard deviation. The value of the m parameter of the M-G relation was 0.90 in the 316LN steel and 0.84 in the Cr-Mo steel. The value of the $m^*$ parameter of the modified relation was 0.94 in the 316LN steel and 0.89 in Cr-Mo steel. The modified relation was superior to the M-G relation because the $m^*$ slopes almost overlapped regardless of creep testing conditions and chemical variations to the two alloy systems.

• 폴리머
• /
• 제30권1호
• /
• pp.70-74
• /
• 2006

셀룰로오스 디아세테이트(CDA)에 가소제로서 트리아세틴(TA)과 에폭시화된 콩기름(ESO)을 첨가하여 고속믹서에서 일차적으로 CDA를 가소화한 후, 여기에 화학적으로 처리한 라미섬유를 각각 첨가하여 천연섬유 복합체를 제조하였다. DMA측정에서 $tan\;\delta$ 피크로부터 유리전이 온도를 확인한 결과, 가소화된 CDA혼합체는 $85\;^{\circ}C$를 나타내고 여기에 라미섬유를 첨가하여 복합화한 필름의 경우는 $55\;^{\circ}C$ 증가한 $140\;^{\circ}C$의 $T_g$를 보였다. 기계적 강도 측정에서는 알칼리 처리된 라미섬유 필름이 상용화된 폴리프로필렌에 비교하여 인장강도와 탄성률이 각각 $15\%$와 $41\%$향상된 높은 수치로 우수한 물성이 관찰되었다 또한 복합 필름의 SEM 이미지로부터 알칼리 처리한 라미섬유(A1Ra)는 가소화된 CDA간의 계면접착성이 향상되었음을 확인할 수 있었다.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2017년도 춘계학술대회 논문집
• /
• pp.80-80
• /
• 2017

Titanium and its alloys that have a good biocompatibility, corrosion resistance, and mechanical properties such as hardness and wear resistance are widely used in dental and orthopedic implant applications. However, they do not form a chemical bond with bone tissue. Plasma electrolytic oxidation (PEO) that combines the high voltage spark and electro-chemical oxidation is a novel method to form ceramic coatings on light metals such as tita-nium and its alloys. This is an excellent re-producibility and economical, because the size and shape control of the nano-structure is relatively easy. Silicon (Si), manganese (Mn), and magne-sium (Mg) have a useful to bone. Particularly, Si has been found to be essential for normal bone, cartilage growth, and development. Mn influences regulation of bone remodeling be-cause its low content in body is connected with the rise of the concentration of calcium, phosphates and phosphatase out of cells. Pre-studies have shown that Mg plays very im-portant roles in essential for normal growth and metabolism of skeletal tissue in verte-brates and can be detected as minor constitu-ents in teeth and bone. In this study, Electrochemical behavior of plasma electrolytic oxidized films formed in solution containing Mn, Mg and Si ions were researched using various experimental in-struments. A series of Si-Mn-Mg coatings are produced on Ti dental implant using PEO, with the substitution degree, respectively, at 5 and 10%. The potentiodynamic polarization and AC impedance tests for corrosion behav-iors were carried out in 0.9% NaCl solution at similar body temperature using a potentiostat with a scan rate of 1.67mV/s and potential range from -1500mV to + 2000mV. Also, AC impedance was performed at frequencies anging from 10MHz to 100kHz for corrosion resistance.

• 센서학회지
• /
• 제1권2호
• /
• pp.131-145
• /
• 1992

본 논문은 SOI트랜스듀서 및 회로를 위해, Si 직접접합과 M-C국부연마법에 의한 박막SOI구조의 형성 공정을 기술한다. 또한, 이러한 박막SOI의 전기적 및 압저항효과 특성들을 SOI MOSFET와 cantilever빔으로 각각 조사했으며, bulk Si에 상당한다는 것이 확인되었다. 한편, SOI구조를 이용한 두 종류의 압력트랜스듀서를 제작 및 평가했다. SOI구조의 절연층을 압저항의 유전체분리층으로 이용한 압력트랜스듀서의 경우, $-20^{\circ}C$에서 $350^{\circ}C$의 온도범위에 있어서 감도 및 offset전압의 변화는 자각 -0.2% 및 +0.15%이하였다. 한편, 절연층을 etch-stop막으로 이용한 압력트랜스듀서에 있어서의 감도변화를 ${\pm}2.3%$의 표준편차 이내로 제어할 수 있다. 이러한 결과들로부터 개발된 SDB공정으로 제작된 SOI구조는 집적화마이크로트랜스듀서 및 회로개발에 많은 장점을 제공할 것이다.

• 한국압력기기공학회 논문집
• /
• 제13권2호
• /
• pp.75-83
• /
• 2017

In severe accident conditions of light water reactors, the loss of coolant may cause problems in integrity of zirconium fuel cladding. Under the condition of the loss of coolant, the zirconium fuel cladding can be exposed to high temperature steam and reacted with them by producing of hydrogen, which is caused by the failure in oxidation resistance of zirconium cladding materials during the loss of coolant accident scenarios. In order to avoid these problems, we develop a multi-metallic layered composite (MMLC) fuel cladding which compromises between the neutronic advantages of zirconium-based alloys and the accident-tolerance of non-zirconium-based metallic materials. Cold pilgering process is a common tube manufacturing process, which is complex material forming operation in highly non-steady state, where the materials undergo a long series of deformation resulting in both diameter and thickness reduction. During the cold pilgering process, MMLC claddings need to reduce the outside diameter and wall thickness. However, multi-layers of the tube are expected to occur different deformation processes because each layer has different mechanical properties. To improve the utilization of the pilgering process, 3-dimensional computational analyses have been made using a finite element modeling technique. We also analyze the dimensional change, strain and stress distribution at MMLC tube by considering the behavior of rolls such as stroke rate and feed rate.

• 한국자동차공학회논문집
• /
• 제18권4호
• /
• pp.40-47
• /
• 2010

This study deals with the investigation about the effect of the pilot and split injection strategies on the spray-atomization characteristics of biodiesel fuel derived from a soybean oil. Experimental results were compared with the calculation results obtained from the numerical analysis. Fuel properties of biodiesel according to the variation of the fuel temperature were inserted to the fuel library in the KIVA code. The amount of fuel injection is divided into equal mass for each split and main injection. In this work, the pilot injection strategy can be achieved by the amount of fuel injection shortly before the start of the main injection. A spray tip penetration, radial distance and spray area were measured for the analysis of macroscopic spray characteristics. In addition, the local and overall droplet size distribution were calculated by using KIVA-3V code to study the effect of split and pilot injection on the atomization performance under high ambient pressure. From these studies, the experimental results showed the multiple injection induced the decrease of the spray tip penetration due to the reduction and division of the spray momentum compared to single injection. In the atomization performance, the droplet size increased in the case of the multiple injection a little. Moreover, the SMD slightly increased as the fuel droplets goes through the axial direction. The spray behavior of numerical results were well predicted the experimental multiple spray characteristics of biodiesel fuel.

• Elastomers and Composites
• /
• 제50권2호
• /
• pp.103-109
• /
• 2015

In this study, epoxy/anhydride mixing ratio for the highly silica filled compounds with chromium (III) octoate catalyst was investigated at a low curing temperature ($71^{\circ}C$ for 40 hr) by evaluating the compressive strength with the weight ratio ranges from 0.3/1.0 to 1.0/1.0 of epoxy part (Part A)/anhydride part (Part B). In case of epoxy/anhydride compounds used surface unmodified silica by coupling agent, these compounds need excess anhydride unlike the weight ratio in the conventional epoxy/anhydride compounds. In curing behavior, the epoxy/anhydride compounds containing chromium (III) octoate showed high conversions at $71^{\circ}C$ for 40 hr, even if a dipropylene glycol (DPG) was not used as a polymerization initiator. Also, DPG leads to a poor epoxy network structure. In conclusion, the appropriate weight ratio of Part A/Part B of highly silica filled epoxy/anhydride compounds with chromium (III) octoate catalyst is 0.5/1.0 and the maximum amounts of silica is 1470 phr of epoxy resin.

• The Journal of Advanced Prosthodontics
• /
• 제7권2호
• /
• pp.98-107
• /
• 2015

PURPOSE. The aim of this study was to appraise the some mechanical properties of polymethyl methacrylate based denture base resin polymerized by copolymerization mechanism, and to investigate the cytotoxic effect of these copolymer resins. MATERIALS AND METHODS. 2-hydroxyethyl methacrylate (HEMA) and isobutyl methacrylate (IBMA) were added to monomers of conventional heat polymerized and injection-molded poly methyl methacrylate (PMMA) resin contents of 2%, 3%, and 5% by volume and polymerization was carried out. Three-point bending test was performed to detect flexural strength and the elasticity modulus of the resins. To determine the statistical differences between the study groups, the Kruskall-Wallis test was performed. Then pairwise comparisons were performed between significant groups by Mann-Whitney U test. Agar-overlay test was performed to determine cytotoxic effect of copolymer resins. Chemical analysis was determined by FTIR spectrum. RESULTS. Synthesis of the copolymer was approved by FTIR spectroscopy. Within the conventional heat-polymerized group maximum transverse strength had been seen in the HEMA 2% concentration; however, when the concentration ratio increased, the strength decreased. In the injection-molded group, maximum transverse strength had been seen in the IBMA 2% concentration; also as the concentration ratio increased, the strength decreased. Only IBMA showed no cytotoxic effect at low concentrations when both two polymerization methods applied while HEMA showed cytotoxic effect in the injection-molded resins. CONCLUSION. Within the limitations of this study, it may be concluded that IBMA and HEMA may be used in low concentration and at high temperature to obtain non-cytotoxic and durable copolymer structure.