• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2000.04a
• /
• pp.183-186
• /
• 2000

The high temperature deformation behavior of spray-formed Al-19wt%Si-1.87wt%Mg-0.085wt.%Fe alloy was studied by torsion testing in the strain rate range of 0.001-1 sec-1 and in the temperature range of 300-500 $^{\circ}C$. The relationship between stress temperature and strain rate is expressed using the Power law. the behavior of dynamic recrystallization is showed in 300-35$0^{\circ}C$, 1-0.1sec-1 and the behavior of dynamic recovery is showed in 450-50$0^{\circ}C$, 0.01-0.001sec-1 The size of Si particles is mall when the temperature is low and the strain rate is high. The strain rate sensitivity(m) and the apparent activation energy(Q) indicate the dependence on strain rate and temperature for flow stress respectively. The hot ductility is high when m is high and Q is low. The maps of strain rate sensitivity and apparent activation energy suggest the optimum processing conditions.

• Journal of Environmental Science International
• /
• v.7 no.5
• /
• pp.725-733
• /
• 1998

Three numerical experiments are done using IAP(Institute of Atmospheric Physics) global spectral model(T42L9) to investigate the influence of the surface temperatures on the 7-day simulation. Particularly, the response of the subtropical High in summer to the variation of soil temperature and sea surface temperature(SST) was emphasized through a series of experiments. Experiment 1 uses the June climate data as the earth surface conditions. Experiment 2 is similar to Experiment 1 except for the soil surface temperature. Experiment 3 is the same as Experiment 1 except for the modified SST, which is much warmer than the June climate SST on the sea around the Korean peninsula. The main finding in 7-day simulation is that the response of the subtropical high in summer to the variation of the sell surface temperature was much more than that to the variation of the SST. It is implied that the proper treatment of sell surface temperature is more important than that of the SST for the better 7-day simulation of the subtropical high in summer.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.22 no.3
• /
• pp.239-247
• /
• 2009

In AC-PDP, it is necessary to achieve high luminance efficacy, high luminance and high resolution by adopting technologies such as high Xenon concentration, MgO doping, and long gap. However, it is very difficult to apply above technologies because they reduce driving voltage margin. For example, doping of MgO reduces driving voltage but introduces new problems such as increased temperature dependency of discharge, which result in larger variations in driving margin at different temperatures. In this paper, we present the experimental results of the characteristics of temperature-dependent discharges. In addition, we suggest the mechanism of bright noise, black noise, and high temperature mis-discharge, which depend on temperature-dependent characteristics of MgO.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2007.10a
• /
• pp.302-305
• /
• 2007

In recent years, many researches on new storage media with high capacity and information are developing. For manufacture of optical storage with high capacity, the injection molding process is generally used. In order to increase the filling ratio of the injection molding structure, the injection molding process required for high injection pressure, packing pressure and temperature control of the mold. However, conventional injection molding process is difficult to increase the filling ratio using injection master with the range of several nanometers and high aspect ratio. In order to improve and increase filling ratio of nano-structure with high aspect ratio, the active temperature control of injection mold was used. Experimental conditions were used injection pressure, time and temperature. Consequently, by using the peltier device into injection mold, we carried out the efficient and active temperature control of mold at low cost.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2014.11a
• /
• pp.141-142
• /
• 2014

Decrease of performance degradation of High Strength Concrete occurs more than that of normal strength concrete at elevated temperature. Therefore, when it comes to evaluating performance of structures, strain of concrete subjected to elevated temperature and loading are important items. In this study, creep strain of High Strength Concrete sunjected to various temperature conditions and 33% loading was evaluated. As a result, creep strain increased with increase of temperature and loading. Creep strain of concrete at high temperature is influenced by loading.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2021.11a
• /
• pp.146-147
• /
• 2021

In this study, the deterioration of concrete subjected to high temperature was evaluated using harmonics. When concrete is exposed to high temperatures, its mechanical properties deteriorate. In order to evaluate this deterioration, a method of analyzing the waveform of elastic waves was applied. As the heating temperature increased, the fundamental wave of the 50 kHz elastic wave passing through the concrete decreased. In addition, harmonics were generated at each temperature, and the higher the heating temperature, the greater the ratio of harmonics. The higher the compressive strength, the greater the amplitude of the fundamental wave, and this phenomenon is thought to be due to the internal structure of concrete.

• Journal of the Korean Society for Precision Engineering
• /
• v.30 no.7
• /
• pp.673-678
• /
• 2013

Driving gear units can be affected by various problems, including those associated with external or internal defects in the bearing, problems with the lubricant oil, high-loading of the railway, and frequent impacts generated by rail joints. Temperature monitoring is a basic method in diagnosing abnormal conditions in the reduction gear and other components. This paper describes a new wireless monitoring system for the temperature diagnosis of abnormal conditions of the reduction gear. Integrated circuit (IC)-type temperature sensors were installed in the reduction gear box of a high-speed railway car. The temperature data from the reduction gear were acquired and analyzed in situ during high-speed rail operation. Analysis of these data was used to alert the driver and/or maintenance personnel when problems occurred.

• Journal of Environmental Health Sciences
• /
• v.38 no.6
• /
• pp.460-471
• /
• 2012

Objectives: Due to global warming resulting from climate change, there has been increasing interest in the relationship between temperature and mortality. These temperature-related deaths depend on diverse conditions related to a given place and person, as well as on time. This study examined changes in the impact of high temperatures on death in summer, using the effect and burden of elevated temperatures on deaths in Seoul and Daegu. Methods: A Poisson regression model was used to estimate short-term temperature effects on mortality. Temperature-related risks were divided into three time periods of equal length (1996-2000, 2001-2005, and 2006-2010). In addition, in order to compare the impact of high temperatures on deaths, this study calculated the proportion of attributable deaths to population, which simultaneously considers the threshold and the slope above the threshold. Results: The effect and burden of high temperatures on deaths is high in Daegu. However, the impact (i.e. the effect and burden) of elevated summer temperatures on deaths has declined over the past 15 years. Sensitivity analyses using alternative thresholds show the robustness of these findings. Conclusion: This study suggests that the attributable burden of high temperatures on deaths to be more plausible than relative risk or threshold for comparing the health impact of high temperatures across populations. Moreover, these results contain important implications for the development or the adjustment of present and future strategies and policies for controlling the temperature-related health burden on populations.

• Korean Journal of Agricultural Science
• /
• v.41 no.4
• /
• pp.291-298
• /
• 2014

Plastic film houses are directly associated with increases in plant growth and yield of vegetable crops through a year round cultivation, however, at the same time temperature stresses are one of fates which are difficult to avoid during crop growth. The objective of this study was to examine the translocation and distribution of minerals (N, P, K) and carbohydrates as well as seasonal fluctuation of mineral uptake and carbohydrate production in cucumber plant grown under moderately high temperature. The temperature treatments consisted of 2-layers film houses (optimal temp.) and 3-layers (high temp.). Shoot growth of cucumber plants were linearly increased until 14 weeks after transplanting (WAT) without any significant difference between both temperatures, and the slowdown was observed from 16 WAT. The level of soluble sugar and starch was slightly greater in optimal temperature compared to the high. Cumulative accumulation of soluble sugar was significantly different before and after 12 WAT in both treatments, whereas starch level represented a constant increase. Monthly production of soluble sugar reached the peak between 12 to 16 WAT, and starch peaked between 4 to 8 WAT and 12 to 16 WAT. Total uptake of N, P and K in optimal and high temperature conditions was $18.4g\;plant^{-1}$ and 17.6 for N, 4.7 and 5.1 for P, and 37.7 and 36.2 for K, respectively, and the pattern of monthly N uptake between optimal and high temperatures was greater in early growth stage, whereas was greater in mid growth stage in both P and K. Thus, this study suggests that moderately high temperature influences much greater to photosynthesis and carbohydrate production than plant biomass and mineral uptake. On the basis of the present result, it is required to indentify analysis of respiration rates from plant and soil by constantly increasing temperature conditions and field studies where elevated temperatures are monitored and manipulated.

• Journal of the Korean Ceramic Society
• /
• v.53 no.5
• /
• pp.506-510
• /
• 2016

The eutectic melt of BaO-CuO flux is known to be a potential sintering aid for $Ba(Zr,Y)O_3$ (BZY) electrolyte for proton-conducting ceramic fuel cells (PCFCs). A density of BZY higher than 97% of theoretical density can be achieved via sintering at $1300^{\circ}C$ for 2 h using a flux composed of 28 mol% BaO and 72 mol% CuO. In the present study, chemical and structural evolution of BaO-CuO flux throughout the sintering process was investigated. An intermediate holding step at $1100^{\circ}C$ leads to formation of various impurity compounds such as $BaCuO_{1.977}$, $Ba_{0.92}Cu_{1.06}O_{2.28}$ and $Cu_{16}O_{14.15}$, which exhibit significantly larger unit cell volumes than the matrix. The presence of such secondary compounds with large lattice mismatch can potentially lead to mechanical failure. On the other hand, direct heating to the final sintering temperature produced CuO and $Cu_2O$ as secondary phases, whose unit cell volumes are close to that of the matrix. Therefore, the final composition of the flux is strongly affected by the thermal history, and a proper sintering schedule should be used to obtain the desired properties of the final product.