• 한국지반환경공학회 논문집
• /
• 제14권9호
• /
• pp.13-19
• /
• 2013

천곡동굴은 동해시에 자리잡고 있는 석회암동굴로서 많은 돌리네를 가지고 있어 관광적 가치와 교육적 가치가 매우 높다. 하지만 천곡동굴은 시가지에 위치하고 있어 접근이 용이한 반면 하수의 유입 등에 의해 환경적 영향을 받을 가능성이 매우 크다. 본 연구에서는 천곡동굴의 수질환경을 장기 모니터링하여 생태계의 영향을 조사하고, 향후 장기 모니터링을 위한 인자를 선정하였다. 그 결과 천곡동굴 내 지하수의 수온은 $14^{\circ}C$, 용존 산소량은 10mg/L 이상, pH는 7-8의 범위에서 안정되게 유지되고 있어, 수생태계에 부정적 영향을 주는 수질적 요소는 없는 것으로 판단되었다. 관람객의 안전을 확보하기 위한 강우기준으로서 일강우로서 60mm/d가 적절하며 향후 장기 모니터링을 위해서 전기전도도를 주된 인자로 이용하고 pH와 탁도를 보조적으로 활용하는 것이 적절하며, 계절적 변화 등을 ORP를 이용하여 모니터링하는 것이 적절하다고 판단되었다.

• 한국세라믹학회지
• /
• 제40권4호
• /
• pp.350-353
• /
• 2003

Millimeter-wave dielectric ceramics have been used like applications for ultrahigh speed wireless LAN because it reduces the resources of electromagnetic wave, and Intelligent Transport System (ITS) because of straight propagation wave. For millimeterwave, the dielectric ceramics with high quality factor (Q$.$f), low dielectric constant($\varepsilon$), and nearly zero temperature coefficient of resonant frequency ($\tau$) are needed. No microwave dielectric ceramics with these three properties exist except Ba(Mg$\_$1/3/Ta/sub1/3/)O$_3$ (BMT), which has a little high s: In this paper, alumina (Al$_2$O$_3$) and fosterite (Mg$_2$SiO$_4$), candidates for millimeter-wave applications, were studied with an objective to get high q$.$f and nearly zero $\tau$$\_$f/ For alumina ceramics, q$.$f more than 680,000 GHz was obtained but it was difficult to obtain nearly zero Qf. On the other hand, for forsterite ceramics, q$.$f was achieved from 10,000 GHz of commercial for sterite to 240,000 GHz of highly purified MgO and SiO$_2$ raw materials, and $\tau$$\_$f/ was reduced a few by adding TiO$_2$ with high positive $\tau$$\_$f/.

• 대한전자공학회논문지SD
• /
• 제37권6호
• /
• pp.34-42
• /
• 2000

우수한 성능을 가지며 소형${\cdot}$경량인 무선통신기기를 구현하기 위해서는 GHz 대의 고주파수에서 동작하는 소형 RF chip 인덕터의 개발은 중요한 연구분야가 되어왔다. 또한 최근 많이 사용되는 자성 ferrite core 재료는 300MHz 이상의 주파수영역에서 자화율이 급속하게 감소하여 고성능 RF chip 인덕터 개발에 큰 장애가 되고 있다. 따라서 본 논문에서는 비정질 $Al_2O_3$ 코아 재료를 응용한 단순 solenoid 형태의 소형${\cdot}$고성능 RF chip 인덕터를 연구하였다. Cu를 코일 (직경=40${\mu}m$)로 사용하였고 인덕터 크기는 $2.1mm{\times}1.5mm{\times}1.0mm$였다. 외부 전류원은 코일의 양단을 코아 가장자리에 적층된 Au 막에 본딩시킨 후 인가되었다. 코아의 성분은 EDX를 사용하여 분석하였다 개발된 인덕터의 인덕턴스 (L), quality factor (Q), 인피던스(Z)등의 주파수 특성은 RF impedance/Material Analyzer (HP16193A test fixture가 장착된 HP4291B)로 측정되었다. 인덕터들의 인덕턴스 값은 22 nH ~ 150 nH 범위를 가지며, 이들의 자기공진주파수 (SRF)는 1~3.5GHz 영역을 나타낸다. 또한 자기공진주파수가 증가함에 따라 인덕턴스 값이 감소하는 경향을 보이고 있다. 임피던스는 공진주파수에서 최대 값을 가지며 Q-factor의 값은 500 MHz ~ 1.5 GHz 주파수 범위에서 최대 70~97까지 얻어졌다.

• 산업경영시스템학회지
• /
• 제43권3호
• /
• pp.101-111
• /
• 2020

Companies struggle to make their best products with high quality and service at a competitive price in global markets. However, customer needs and requirements keep changing with a variety of situations. Companies that face the changes can not stay the same and make an effort to adapt themselves to new circumstances. They would probably review the overall management system that is currently implementing to improve management efficiency. Among other things, quality might be considered to be a crucial element if they are manufacturing industries to be sustained in global markets. KSA (Korean Standards Association) is a government-affiliated organization under the Ministry of Trade, Infrastructure, and Energy. It is a Korean standards provider for quality and service industry. KSA confers national commendations for organizations, quality circles, artisans, QCEC (Quality Competitive Excellent Company), and the most honorable KNQA (Korean National Quality Award) every year. KSA established KNQA on the basis of Malcom Baldrige National Quality Award, Deming Prize, and European Quality Award. Research on quality awards shows that there are many similarities in the framework. Although KSA summarizes two factors for 13 evaluation indicators in the quality competitive excellent model of QCEC, the categorization is ambiguous to explain them according to earlier studies. We performed a deep analysis of foreign quality awards and background for KNQA and QCEC. We conducted a content analysis of KNQA and QCEC and matched evaluation items that were closely related. We proposed a quality competitiveness model with three factors, Technology, System, and Tools, summarizing 13 evaluation indicators in QCEC. Based on audit data for six years from 2012 to 2017 we carried out a confirmatory factor analysis for the proposed model by examining the model validity and fitness.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 추계학술대회 논문집 Vol.14 No.1
• /
• pp.386-389
• /
• 2001

In this study, development of a new LTCC material using non-glassy system was attempted with repsect to reducing the fabrication process steps and cost down. Lowering the sintering temperature can be achieved by liquid phase sintering. However, presence of liquid phases usually decrease dielectric properties, especially the quality factor. Therefore, the starting material must have quality factor as high as possible in microwave frequency range. And also, the material should have a low dielectric constant for enhancing the signal propagation speed. Regarding these factors, dielectric constants of various materials were estimated by the Clausius-Mosotti equation. Among them, $ZnWO_4$ was turned out the suitable LTCC material. $ZnWO_4$ can be sintered up to 98% of full density at $1050^{\circ}C$ for 3 hours. It's measured dielectric constant, quality factor, and temperature coefficient of resonant frequency were 15.5, 74380GHz, and $-70ppm/^{\circ}C$, respectively. In order to modify the dielectric properties and densification temperature, $B_{2}O_{3}$ and $V_{2}O_{5}$ were added to $ZnWO_4$. 40 mol% $B_{2}O_{3}$ addition reduced the dielectric constant from 15.5 to 12. And the temperature coefficient of resonant frequency was improved from -70 to $-7.6ppm/^{\circ}C$. However, sintering temperature did not change due to either lack of liquid phase or high viscosity of liquid phase. Incorporation of small amount of $V_{2}O_{5}$ in $ZnWO_{4}-B_{2}O_{3}$ system enhanced liquid phase sintering. 0.1 wt% $V_{2}O_{5}$ addition to the $0.6ZnWO_{4}-0.4B_{2}O_{3}$ system, reduced the sintering temperature down to $950^{\circ}C$. Dielectric constant, quality factor, and temperature coefficient of resonant frequency were 9.5, 16737GHz, and $-21.6ppm/^{\circ}C$, respectively.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 추계학술대회 논문집
• /
• pp.386-389
• /
• 2001

In this study, development of a new LTCC material using non-glassy system was attempted with respect to reducing the fabrication process steps and cost down. Lowering the sintering temperature can be achieved by liquid phase sintering. However, presence of liquid phases usually decrease dielectric properties, especially the quality factor. Therefore, the starting material must have quality factor as high as possible in microwave frequency range. And also, the material should have a low dielectric constant for enhancing the signal propagation speed. Regarding these factors, dielectric constants of various materials were estimated by the Clausius-Mosotti equation. Among them, ZnWO$_4$ was turned out the suitable LTCC material. ZnWO$_4$ can be sintered up to 98% of full density at 105$0^{\circ}C$ for 3 hours. It's measured dielectric constant, quality factor, and temperature coefficient of resonant frequency were 15.5, 74380GHz, and -70ppm/$^{\circ}C$, respectively In order to modify the dielectric properties and densification temperature, B$_2$O$_3$ and V$_2$O$_{5}$ were added to ZnWO$_4$. 40 mol% B$_2$O$_3$ addition reduced the dielectric constant from 15.5 to 12. And the temperature coefficient of resonant frequency was improved from -70 to -7.6ppm/$^{\circ}C$. However, sintering temperature did not change due to either lack of liquid phase or high viscosity of liquid phase. Incorporation of small amount of V$_2$O$_{5}$ in ZnWO$_4$-B$_2$O$_3$ system enhanced liquid phase sintering. 0.lwt% V$_2$O$_{5}$ addition to the 0.6ZnWO$_4$-0.4B$_2$O$_3$ system, reduced the sintering temperature down to 95$0^{\circ}C$ Dielectric constant, quality factor, and temperature coefficient of resonant frequency were 9.5, 16737GHz, and -21.6ppm/$^{\circ}C$ respectively.ively.

• 한국정보시스템학회지:정보시스템연구
• /
• 제18권3호
• /
• pp.251-276
• /
• 2009

Maintaining online services of high quality has become a crucial factor for brokerages to gain competitive advantages. Because of the attributes of the product uniformity of online trading, online brokerages have grown significantly with IT development, since the early 2000s. Now, as the online trading business gets mature, the profitability of the IT investment and the quality of IT-based services became questioned. This study examines the issues of IT investment and its contribution by analyzing the relationship between the quality of online service and IT investment. In addition, it also investigates the relationship of the quality of online services and profitability of brokerage. Our results show that IT investment draws cubic-style, curvilinear relationship with the service quality of online trading and only high quality services can lead to the increase of profitability.

• 한국의류학회지
• /
• 제34권10호
• /
• pp.1647-1657
• /
• 2010

This study examines underwear purchase behaviors and the attitude of male consumers based on the degree of interest in appearance. Data research was conducted on 296 males in their 20s and 30s located in Seoul & Gyeonggi province. The SPSS 17.0 software program was used to conduct data analyses such as descriptive statistics, frequency analysis, factor analysis, cluster analysis, t-test, and $\chi^2$-test. The results of this study are as follows: The degree of interest in appearance was identified with four factors; outfit management, confidence of figure, interest in clothing, weight control, and disinterest in appearance. Customers were segmented into two subdivisions: high and low interest in appearance. The factors derived from the factor analysis of underwear purchase motive included aesthetic, impulsiveness, and practicality. The purchase behavior of the group with high interest in appearance was highly motivated by aesthetics and impulsiveness. The factors derived from the factor analysis of underwear attitude included fashionability, comfortableness, and quality. Customers were segmented into the following three subdivisions: pursuit of comfortableness, pursuit of diversity, and normal. The type of high interest in appearance regarded fashionability and quality highly. Finally, the degree of interest in appearance showed significant relevance in purchase motive and underwear attitude for underwear.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 추계학술대회 논문집
• /
• pp.238-241
• /
• 2000

In this paper, we manufactured Pb($Ni_{1/2}$ $W_{1/2}$)$O_3$-Pb($Mn_{1/3}$$Nb_{2/3}$)$O_3$-Pb($Zr_3$Ti)$O_3$ceramics with variation of milling time and investigated its dielectric and piezoelectric properties. Density was increased with the increase of milling time because the sinterability of specimens were improved with the decrease of particle size. The highest value of electromechanical coupling factor was 0.518 at milling time 5hour. The highest values of mechanical quality factor and dielectric constant were 1566, 1590 at milling time 4hour, respectively.

• 한국생활과학회지
• /
• 제19권2호
• /
• pp.389-398
• /
• 2010

This study examines the relationship between the concern about well-being lifestyle and the perceived image of Hanji fiber. A survey was conducted among male and female consumers aged 20 and over in Jeonju and Daejon from January 4th to 11th, 2008. A total of 168 responses were analyzed by using descriptive statistics, factor analysis, and ANOVA via the SPSS ver. 12. As a result, four factors were determined in the concern for a well-being lifestyle; product consumption, enjoying culture, using therapy and managing the household. The perceived image of Hanji fiber were classified into four elements; traditional, high-quality, functional and popular images. Among the factors of the concern for a well-being lifestyle and the perceived image of Hanji fibers, a partial relationship was observed. There is a positive relationship, especially between the product consumption factor of a well-being lifestyle and the high-quality and functional image of Hanji fiber. Also, there was a positive relationship between the factor of managing the household and the traditional image of Hanji fiber. However, the therapy interest factor of a well-being lifestyle was negatively related to the traditional image of Hanji fiber.