본 연구에서는 테이프의 미소한 수직 변형에 대한 실험을 수행하여 이에 대한 계측 이론 및 계측방법을 정립한다. 회전 헤드와 주행 테이프를 구동할 수 있는 실 험 장치를 개발하고 주행 테이프의 변형을 정밀 계측할 수 있는 측정 시스템을 구성한 다. 이러한 측정 시스템을 이용하여 고속이면서 미소한 주행 테이프의 변형에 대해 비접촉적인 방법으로 3차원 계측을 실시한다. 헤드의 형상 및 크기가 다른 모델들을 설계 및 가공을 통해 제작하여 주행 테이프의 부상 특성을 평가한다. 주행 테이프의 부상 특성에 관한 수치 해석 결과에 대하여 실제와의 부합 여부를 검토할 수 있도록 실험을 수행한다. 본 연구에서 구성한 비접촉 측정 시스템으로 계측한 테이프의 3차 원 변형에 대한 실험 결과와 수치 해석 결과를 비교 검토한다.
In this study, a process combined biofiltration with sulfur-utilizing autotrophic denitrification and membrane separation was proposed to examine the efficiency of nitrogen removal. As an experimental device, hollow-fiber module was installed in the center of reactor to generate the flux forward sulfur layer in the cylinder packed with granular sulfur. In addition, a simple module was installed in activated sludge aeration tank which inside and outside of sulfur-using denitrification module was covered with microfilter and the module was considered as an alternative of clarifier. The experiment for developing new MBR process was carried out for three years totally. As the results of first two-year experiment, successful nitrogen removal performance was revealed with lab-scale test and pliot scale plant using artificial wastewater and actual plating wastewater. In this year, pilot scale test using actual domestic wastewater was performed to prove field applicability. As the results, high-rate nitrogen removal performance was confirmed with about 0.19 kg ${NO_3}^--N/m^3$ day of rate. Also significant fouling and pressure increase were not found during the experiment. And, the production ratio of sulfate and the consumption ratio of alkalinity showed a slightly higher value about 311 mg ${SO_4}^{2-}/L$ and 369 mg $CaCO_3$/L, respectively. In conclusion, the developed MBR process can be utilized as an alternative for retrofiting existing wastewater plants as well as new construction of advanced sewage wastewater treatment plants, with cost-effective merit.
반응성 조정 압축착화 (Reactivity Controlled Compression Ignition, RCCI) 연소는 착화원인 디젤 연료를 압축 행정 중 이른 시점에 미리 분사하여, 공기와 미리 섞여 들어온 천연가스 연료뿐만 아니라 디젤 연료 자체도 미리 연소 전에 공기와 혼합하여 착화를 이루는 전체 예혼합 혼소(Dual-fuel combustion) 방식의 일종이다. 따라서 기존의 혼소 방식 중에서도 RCCI 연소는 질소산화물(Nitrogen Oxides, NOx) 및 매연(Smoke)을 획기적으로 줄일 수 있고, 또한 높은 열효율을 유지할 수 있는 장점을 지니고 있다. 특히 연소 중 NOx의 발생은 연소 온도와 국부적인 당량비에 관계된 상황에서 당량비를 낮추기 위해 예혼합율을 높이는 시도뿐만 아니라, 연소 온도 감소를 위한 배기재순환(Exhuast Gas Recirculation, EGR)을 적용하는 것이 효과적이다. 그러나 배기재순환은 대개의 경우 터보차저의 압축기 전단에서 추출하는 HP-EGR(High Pressure-EGR) 방식을 적용하는 경우가 많으므로, EGR율을 높일 경우 터빈으로 공급되는 배기의 양이 줄어 배기 엔탈피 감소로 인해 과급이 줄어드는 악영향을 초래할 수 있다. 따라서 본 연구에서는 서로 다른 두 운전조건에서 천연가스-디젤 RCCI 연소를 시행할 때, EGR율 변화에 따른 엔진 시스템의 제동 출력 및 열효율의 변화에 대하여 실험적으로 분석하였다. 실험 조건은 1,200 rpm/29 kW 수준의 조건과 1,800 rpm/90 kW 이하 조건에서 수행하였으며 NOx와 smoke의 배출조건은 Tier-4 final 배기규제를 기준으로 삼았으며 엔진의 내구성을 고려하여 최고 연소압력은 160 bar를 넘지 않게 제어하였다. 그 결과 1,200 rpm/29 kW 조건에서는 EGR율을 4에서 30 %로 높이더라도 출력 및 열효율의 변화는 미미하였으나, 1,800 rpm 조건에서는 EGR율을 4에서 28 %로 증가할 경우 최대 과급 압력이 2.3에서 1.8 bar로, 최고 출력은 90에서 65 kW로, 열효율은 37에서 33 %로 감소함을 알 수 있었다. 따라서 효과적인 EGR공급을 위해서는 현재 압축기 전단에서 추출하는 EGR을 후단에서 추출하는 LP-EGR (Low Pressure EGR) 시스템이 효과적일 수 있음을 시사한다.
본 논문은 국내 고속형 화물열차에 적용되는 P4a 분배밸브를 갖는 화물열차의 장대 편성시 제동특성에 관한 것이다. 제동신호가 열차의 끝단까지 연결된 제동관을 통해 공기압력으로 전달되는 화차의 제동은 열차 길이와 사용된 밸브 등에 따라 영향을 받기 때문에 실험적 방법으로 확인한다. 장대화물 열차의 제동 특성은 평상시 운영의 약 2배인 50량으로 구성한 화물열차의 비상제동과 상용제동의 시험을 이용하였다. 1, 10, 20, 30, 50번째 차량에서 제동 실린더 압력이 측정되었다. 열차의 길이가 길어질수록 후방의 차량은 제동이 늦게 체결되는 제동지연 현상을 확인하였으며 특히 비상제동시 차량간 충격이 클 것을 예상할 수 있었다. 제한된 시험의 결과를 보완하고 향후 제동거리 계산을 위해 열차를 구성하는 모든 차량에서의 제동 압력을 예측할 필요가 있다. 제동시 각 차량에서의 압력은 계산시간의 단축과 신뢰성 있는 정보를 제공하는 것으로 알려진 선형보간, 단계형, 지수함수형의 경험적 모델들을 이용하여 예측하였다. 경험적 모델들의 예측결과는 실측한 결과들과 비교하였으며 지수함수형 모델이 비교적 정확하게 예측하고 있음을 확인하였다. 본 연구의 결과는 장대화물열차의 안전한 운용에 기여하고 화물열차의 제동거리 예측과 제동시 차량간 충격량 계산 등에 활용될 수 있을 것으로 예상된다.
대부분의 소비자들이 질 좋은 음식을 선호하기 때문에, 농장에서는 소비자들의 욕구를 충족시키기 위해 다양한 시설을 이용하고 있다. 가장 대표적인 시설은 플라스틱 온실과 유리온실이다. 국내의 플라스틱 온실 과 유리 온실의 측고는 3m 내외이다. 결과적으로 작물의 생산성이 제한되고, 이를 해결하기 위해서는 기둥의 높이를 증가시켜 온실의 측고를 높이는 것이다. 온실 기둥상승 장치는 멈춤장치, 공압 실린더 및 수직 부재 등으로 구성된다. 공압 실린더는 안전계수 1.5를 고려하여 직경 160mm와 행정길이 50mm로 설계하였으며, 노즐을 통하여 공기의 압력을 제어하였다. 1행정 시간을 30초 내외로 설계하기 위해서는 $21.5L{\cdot}min^{-1}$ 공기가 필요한 것으로 나타났다. 따라서 노즐의 직경은 0.5mm로 설계하였다. 압력이 0.9 MPa일 때 평균 인상력은 13,805N으로 계산된 값 15,612N에 근접하였다. 현장 시험결과 같은 열의 기둥과 오차가 발생하지 않았으며, 실제 유리 및 플라스틱 온실에 적용 가능한 것으로 판단되었다.
Kwon, Eunhee;Kang, Eun Kyu;Min, Jung Wook;Lee, Yong Tak
한국진공학회:학술대회논문집
/
한국진공학회 2013년도 제45회 하계 정기학술대회 초록집
/
pp.221-221
/
2013
Vertical LED (VLED) has been recognized as a way to obtain the high-power LED due to their advantages [1]. However, approximately 4% of the light generated from the active region is extracted, if the light extraction from side walls and back side is neglected because of Fresnel reflection (FR) and total internal reflection (TIR) [2,3]. In this study, the optical simulation of the VLED with the various microstructures was performed. Among them, the microlens having the diameter of 3 ${\mu}m$ and the height of 1.5 ${\mu}m$ shown the best result was chosen, and then, optimized microlens was formed on a GaN template using conventional semiconductor process. Various microstructures were proposed to improve the light extraction efficiency (LEE) of the VLED for the simulation. The LEE was simulated using LightTools based on a Monte Carlo ray tracing. The microstructures with hemisphere, cone, truncated and cylinder pattern having diameter of 3 ${\mu}m$ were employed on the top layer of the VLED respectively. The improvement of the LEE by using the microstructure is 87% for the hemisphere, 77% for the cone, 53% for the truncated, 21% for the cylinder, compared with the LEE of the flat surface at the reflectance of 85%. The LEE was increased by 88% at the height of 1.5 ${\mu}m$, compared with the LEE of the flat surface. We found that the microlens on the top layer is the most suitable for increasing the LEE. In order to apply the proposed microlens on n-GaN surface, we fabricated microlens on a GaN template. A photoresist array having hexagonal-closed packed microlens was fabricated on the GaN template. Then, optimization of etching the GaN template was performed using a dry etching process with ICP-RIE. The dry etching carried out using a gas mixture of Cl2 and Ar, each having a flow rate of 16 sccm and 10 sccm, respectively with RF power of 50 W, ICP power of 900 W and chamber pressure of 2 mTorr was the optimum etching condition as shown in Fig. 2(a).
액화석유가스는 배관을 통해 공급되는 도시가스와 달리 용기 또는 소형저장탱크와 같이 독립된 저장방식이 사용되며 이러한 사용특성에 의해 사고 발생률이 높다. LP가스 사고가 주로 발생하는 주택 및 업소는 인구밀집도가 높기 때문에 사고 발생 시 대규모 인명피해로 이어질 수 있는 우려가 있다. 이로 인해 액화석유가스는 타 가스에 비해 인명피해율이 높아 안전관리 강화에 대한 필요성이 꾸준히 제기되어왔다. 이에 따라 1996년 한국가스안전공사에서는 LP가스 누출시험을 진행한 바 있다. 본 연구는 1996년 실험을 바탕으로 외기온도, 배관 상태 등의 추가 조건을 설정하여 LP가스 용기의 가스 누출량 측정실험을 진행하였다. 이를 통해 LP가스 누출의 여러 시나리오에 대한 누출경향을 확인하였다. 가스누출에 있어서 조정기 등 감압에 영향을 줄 수 있는 용품이 연결되지 않은 누출의 경우 외기 온도에 의해 누출량의 변화가 크게 나타나고, 조정기와 같은 용품이 체결될 경우 출구압에 의한 영향이 큰 것으로 나타났다. 본 실험의 결과를 통해 추후 발생할 수 있는 LP가스 누출 사고에 대한 누출량 판단에 기초자료로 활용되어 가스안전관리 방안에 효과가 있기를 기대한다.
Clacic amphiboles along the tremolite (Tr)-tschermakite(Ts) joint were synthesized using a piston-cylinder appratus. At 750-85$0^{\circ}C$and 12-2 kb, amphibole+corundum coexist with zoisite($\pm$talc, chlorite, and Mg-staurolite), but with anorthite($\pm$cholorite, spinel, pyroxenes, and sapphirine) at lower P. At 90$0^{\circ}C$, amphibole+corundum+clinopyroxene($\pm$anorthite, forsterite, sapphirine, and garnet) are stable over the P range 12-18 kb. These amphibole-bearing assemblages are replaced at high P by clcinopyroxene+talc+chlorite+zoisite at 650-75$0^{\circ}C$, and at higher temperatures by garnet+clinopyroxene($\pm$zoisite, orthopyroxene, and Mg-staurolite). Synthetic amphiboles with Ts>~45 mol% contain as much as 0.15 excess cations per formula unit(pfu) based on 23 oxygens(anhydrous formula), whereas less tschermakitic ones are deficient in cation occupancy by up to 0.18 pfu. This trend is attributed to the 야/trioctahedral substitution in Ca-amphiboles. Compositions of synthetic amphiboles display systematic changes with P and T governed by coexisting mineral assemblages. The Ts content (=[8-Si-Na]/2) increases with increasing T( Ts/ T=~0.1 nik% K-1) in the range 750-85$0^{\circ}C$, but remains nearly constant at 850-90$0^{\circ}C$. Pressure dramatically affects the Ts content of Ca-amphiboles:it increases with P at 8-12 kb( Ts/ T=2-3 mol% K-1), but significantly decreases at 12-21 kb( Ts/ P=-2.5 mol% Kb-1). Hence, the most tschermakitic amphiboles, containing 60$\pm$5 mol % Ts, or 1.2$\pm$0.1 tetrahedral Al, occur at 12 kb and 850-90$0^{\circ}C$. Compositions of Ca-amphiboles defined by a simple reaction, 3 Tr+2 zoisite+7 corundum+H2O=5 Ts, are reversed and used to estimate thermodynamic parameters of tschermakite assuming ideal mixing of Tr-Ts solid solutions. Predicted standard molal entropy and enthalpy of tschermakite are : S$^{\circ}$of Tr-Ts solid solutions. Predicted standard molal entropy and enthalpy of tschermakite are : S$^{\circ}$=566.9$\pm$13.7 J mol-1K, -1and H$^{\circ}$=-12518.36$\pm$15.17 kJ mol.-1
A 50 kW class rotating body type wave energy converter consisted of two floating bodies and a PTO (Power Takeoff) unit is studied. As an wave energy extractor, the body is designed to have a VLCO (Variable Liquid-Column Oscillator) having a liquid filled U-tube with air chambers. Owing to the oscillation of the liquid in the U-tube caused by the air spring effect of the air chambers, the amplitude of response of the VLCO becomes significantly amplified for a target wave period. The PTO converts the rotational moment introduced from the relative motion of the hinged bodies to an hydraulic power by means of a cylinder. A high pressure accumulator, hydraulic motor and a generator are equipped in the PTO to convert the hydraulic power to electric power. A control law for adjusting the oscillation period of the VLCO is proposed for the efficient operation of the VLCO with various wave conditions. It is found that the effect of the air spring has an important role to play in making the oscillation of the VLCO match with the ocean wave. In this way, the wave energy converter equipped with the VLCO provides the most effective mode for extracting energy from the ocean wave.
이 논문의 목적은 자동차 에어컨 가스 누설에 관련된 고장사례를 분석하고 고찰한 것이다. 첫 번째 사례는 냉매가 누설된 상태에서 에어컨 컴프레서가 계속 작동되었다. 이로 인해 에어컨 컴프레서 내부의 피스톤이 윤활부족으로 인해 피스톤이 부분적으로 에어컨 컴프레서 내부의 실린더에 소착되는 현상이 발생하였다. 이것이 엔진작동 중 부하를 증대시켜 엔진의 회전수 변동과 함께 엔진의 작동이 정지되는 현상이 발생된 것으로 확인되었다. 두 번째 사례는 에어컨 라인과 관련 시스템을 확인한 결과 에어컨 컴프레서에서 뒤쪽으로 가는 컨덴서 고압파이프에서 미세한 균열에 의해 에어컨 냉매 가스가 누설되는 것을 확인하였다. 세 번째 사례는 에어컨 컨덴서 핀 부에서 육안으로 확인하기 어려운 미세한 크랙에 의해 컨덴서 내부 안쪽에서 에어컨 가스가 미세하게 누설되는 것을 확인하였다. 따라서, 에어컨 시스템은 에어컨 냉매가스에 의해 자동차의 실내의 온도를 낮춰 공기조화를 하는 시스템이므로 최적의 상태를 유지할 수 있도록 철저한 관리를 하도록 하여야 한다.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.