• 드라이브 ㆍ 컨트롤
• /
• 제13권2호
• /
• pp.1-9
• /
• 2016

In this paper, an elementary force fighting problem was investigated. The problem is encountered when a double-rod type EHA(electro-hydrostatic actuator) is combined with a single-rod type EHA to build a redundant actuator system with synchronized motion. When the rod-side chambers of the two different types of EHAs have the same effective piston areas and are simultaneously pressurized by an external load, the two EHAs behave identically, sharing the external load equally. However, when the piston head-side chamber of the single rod type EHA, having a larger effective area than the rod-side chamber, is pressurized by the external load, an abnormal force fighting between the two EHAs occurs, unless their pump speeds are properly decoupled. In this study, the output drive forces of each EHA were obtained from the cylinder pressure signals and applied to the position control for each EHA to maintain the balance between their pump speeds. Adding minor force difference feedback loops to the position control, the force fighting phenomena could be eliminated and steady state synchronization errors were reduced. The power consumption of the pumps also could be remarkably reduced, avoiding unnecessarily high load pressures to the pumps.

• 콘크리트학회논문집
• /
• 제15권5호
• /
• pp.726-736
• /
• 2003

섬유에 의하여 보강된 콘크리트의 압축강도와 최대 변형률은 현저하게 증가한다. 지난 10여년간 섬유보강 콘크리트의 구속효과에 대한 많은 연구가 수행되었지만, 기존 제안식의 대부분은 횡구속된 콘크리트의 압축강도 예측에 중점을 두고 있으며, 예측된 최대변형률은 실제값을 과대 또는 과소 평가하는 경향이 있다. 이 논문에서는 콘크리트 실린더 실험을 통해, 섬유보강된 콘크리트의 압축강도 및 최대변형률을 예측할 수 있는 평가식을 제안하였다. 구속콘크리트의 압축강도와 섬유의 파단강도 및 시험체의 크기효과를 고려하여 제안된 평가식은 기존의 제안식보다 정확하게 구속 콘크리트의 압축강도 및 최대 변형률을 예측하였다. 또한 섬유의 응력-변형률곡선의 특성을 고려하여 제안된 구속 콘크리트의 축방향 응력-변형률곡선은 탄소섬유에 의하여 구속된 콘크리트의 응력-변형률곡선을 기존의 제안식보다 정확하게 추적하였다.

• 한국자동차공학회논문집
• /
• 제15권2호
• /
• pp.8-14
• /
• 2007

Compression ignition of homogeneous charges in IC engines indicates possibilities of achieving the high efficiency of DI diesel engines with low level of NOx and particulate emissions. The objectives of this study are to further understand the characteristics of the HCCI(Homogeneous charge compression ignition) combustion and to find ways of extending the rich HCCI operation limit in an engine-like environment. DME fuel is supplied either in the form of premixture with air or directly injected in the combustion chamber of a rapid compression and expansion machine under the conditions of various equivalence ratio and injection timing. The cylinder pressure is measured and the rate of heat release is computed from the measured pressure for the analysis of the combustion characteristics. The experimental data show that the RCEM can operate without knock on mixtures of higher equivalence ratio, when DME is directly injected in the combustion chamber than introduced as a fraction of a perfect or nearly perfect premixture. Very early fuel injection timings usually employed in HCCI operation are seen to have only insignificant effects in control of ignition timing.

• 한국분무공학회지
• /
• 제21권2호
• /
• pp.95-103
• /
• 2016

The effect of pilot injection quantity on the combustion and emissions characteristics of a compression ignition engine with a biodiesel-compressed natural gas (CNG) dual fuel combustion (DFC) system is studied in this work. Biodiesel is used as a pilot injection fuel to ignite the main fuel, CNG of DFC. The pilot injection quantity is controlled to investigate the characteristics of combustion and exhaust emissions in a single cylinder diesel engine. The injection pressure and injection timing of pilot fuel are maintained at approximately 120 MPa and BTDC 17 crank angle, respectively. Results show that the indicated mean effective pressure (IMEP) of biodiesel-CNG DFC mode is similar to that of diesel-CNG DFC mode at all load conditions. Combustion stability of biodiesel-CNG DFC mode decreased with increase of engine load, but no notable trend of cycle-to-cycle variations with increase of pilot injection quantity is discovered. The combustion of biodiesel-CNG begins at a retarded crank angle compared to that of diesel-CNG at low load, but it is advanced at high loads. Smoke and NOx of biodiesel-CNG are simultaneously increased with the increase of pilot fuel quantity. Compared to the diesel-CNG DFC, however, smoke and NOx emissions are slightly reduced over all operating conditions. Biodiesel-CNG DFC yields higher $CO_2$ emissions compared to diesel-CNG DFC over all engine conditions. CO and HC emissions for biodiesel-CNG DFC is decreased with the increase of pilot injection quantity.

• 대한기계학회논문집
• /
• 제16권8호
• /
• pp.1575-1582
• /
• 1992

본 연구에서는 정상운전 중인 4사이클 6실린더 터보과급 디젤기관에 갑자기 큰 부하가 작용하였을 경우, 기관 및 과급기 관성 모멘트의 변화가 기관과 과급기의 실제 회전속도, 압축기 압력비, 실린더내 공기유량, 연소효율, 배기온도 등의 과도 응 답성능에 미치는 영향을 시뮬레이션해석과 실험을 통하여 규명하였다.

• 한국자동차공학회논문집
• /
• 제15권3호
• /
• pp.54-62
• /
• 2007

The knock characteristics in an engine were investigated under homogeneous charge compression ignition (HCCI) operation. Liquefied petroleum gas (LPG)and gasoline were used as fuels and injected at the intake port using port fuel injection equipment. Di-methyl ether (DME) was used as an ignition promoter and was injected directly into the cylinder near compression top dead center (TDC). A commercial variable valve timing device was used to control the volumetric efficiency and the amount of internal residual gas. Different intake valve timingsand fuel injection amounts were tested to verify the knock characteristics of the HCCI engine. The ringing intensity (RI) was used to define the intensity of knock according to the operating conditions. The RI of the LPG HCCI engine was lower than that of the gasoline HCCI engine at every experimental condition. The indicated mean effective pressure (IMEP) dropped when the RI was over 0.5 MW/m2and the maximum combustion pressure was over 6.5MPa. There was no significant relationship between RI and fuel type. The RI can be predicted by the crank angle degree (CAD) at 50 CA. Carbon monoxide (CO) and hydrocarbon (HC) emissions were minimized at high RI conditions. The shortest burn duration under low RI was effective in achieving low HC and CO emissions.

• Tribology and Lubricants
• /
• 제31권4호
• /
• pp.141-147
• /
• 2015

Gas foil thrust bearings (GFTBs) have attractive advantages over rolling element bearings and oil film thrust bearings, such as oil-free operation, high speed stability, and high-temperature operation. However, GFTBs have lower load carrying capacity than the other two types of bearings owing to the inherent low gas viscosity. The load carrying capacity of GFTBs depends mainly on the compliance of the foil structure and the formed hydrodynamic wedge, where the gas pressure field is generated between the top foil and the thrust runner. The load carrying capacity of the GFTBs is very important for the suitable design of oil-free turbomachinery with high performance. The aim of the present study is to identify the characteristics of the load carrying performance of GFTBs. A new test rig for the experimental measurements is designed to provide static loads up to 800 N using a pneumatic cylinder. The maximum operating speed of the driving motor is 30,000 rpm. A series of experimental tests—lift-off test, static load performance test, and maximum load capacity test—estimate the performance of a six-pad GFTB, in terms of the static load, driving torque, and temperature. The maximum load capacity is determined by increasing the static load until the driving torque rises suddenly with a sharp peak. The test results show that the torque and temperature increase linearly with the static load. The estimated maximum load capacity per unit area is approximately 80.5 kPa at a rotor speed of 25,000 rpm. The test results can be used as a design guideline for GFTBs for realizing oil-free turbomachinery.

• 한국항공우주학회지
• /
• 제44권1호
• /
• pp.23-32
• /
• 2016

초고속으로 비행하는 물체의 항력을 줄이기 위해 노즈콘으로부터 제트를 분사하는 다양한 연구가 진행되고 있다. 본 연구에서는 항력감소의 기초자료와 핵심 변수를 파악하기 위해서 미국의 항력감소용 분사 제트 연구 동향을 조사하고 요약하였다. 연구에 활용한 노즈콘 모델의 형상은 반구 실린더, 잘린 콘, 재돌입 캡슐이었으며, 각 모델의 시험조건에 대해 정리하였다. 항력감소의 핵심 변수는 분사제트의 마하수, 질량유량, 압력비율이다. 항력감소효과는 주어진 조건에 따라 다양한 결과를 보였지만, 최대 40~50% 정도까지 항력이 감소하였다.

• 대한기계학회논문집
• /
• 제15권1호
• /
• pp.107-119
• /
• 1991

본 연구에서는 테이프의 미소한 수직 변형에 대한 실험을 수행하여 이에 대한 계측 이론 및 계측방법을 정립한다. 회전 헤드와 주행 테이프를 구동할 수 있는 실 험 장치를 개발하고 주행 테이프의 변형을 정밀 계측할 수 있는 측정 시스템을 구성한 다. 이러한 측정 시스템을 이용하여 고속이면서 미소한 주행 테이프의 변형에 대해 비접촉적인 방법으로 3차원 계측을 실시한다. 헤드의 형상 및 크기가 다른 모델들을 설계 및 가공을 통해 제작하여 주행 테이프의 부상 특성을 평가한다. 주행 테이프의 부상 특성에 관한 수치 해석 결과에 대하여 실제와의 부합 여부를 검토할 수 있도록 실험을 수행한다. 본 연구에서 구성한 비접촉 측정 시스템으로 계측한 테이프의 3차 원 변형에 대한 실험 결과와 수치 해석 결과를 비교 검토한다.

• 상하수도학회지
• /
• 제25권3호
• /
• pp.383-390
• /
• 2011

In this study, a process combined biofiltration with sulfur-utilizing autotrophic denitrification and membrane separation was proposed to examine the efficiency of nitrogen removal. As an experimental device, hollow-fiber module was installed in the center of reactor to generate the flux forward sulfur layer in the cylinder packed with granular sulfur. In addition, a simple module was installed in activated sludge aeration tank which inside and outside of sulfur-using denitrification module was covered with microfilter and the module was considered as an alternative of clarifier. The experiment for developing new MBR process was carried out for three years totally. As the results of first two-year experiment, successful nitrogen removal performance was revealed with lab-scale test and pliot scale plant using artificial wastewater and actual plating wastewater. In this year, pilot scale test using actual domestic wastewater was performed to prove field applicability. As the results, high-rate nitrogen removal performance was confirmed with about 0.19 kg ${NO_3}^--N/m^3$ day of rate. Also significant fouling and pressure increase were not found during the experiment. And, the production ratio of sulfate and the consumption ratio of alkalinity showed a slightly higher value about 311 mg ${SO_4}^{2-}/L$ and 369 mg $CaCO_3$/L, respectively. In conclusion, the developed MBR process can be utilized as an alternative for retrofiting existing wastewater plants as well as new construction of advanced sewage wastewater treatment plants, with cost-effective merit.