• 전력전자학회논문지
• /
• 제10권4호
• /
• pp.313-322
• /
• 2005

본 논문은 복공진 인버터를 적용한 250[W] 메탈핼라이드램프를 구동하기 위한 고역률 전자식 안정기를 설계하고 구현하였다. 제안된 전자식 안정기는 역률 개선 회로기능을 갖는 부스트 능동 PFC 회로와 하프 브리지 복공진형 인버터로 구분된 2개의 전력처리단으로 구성되어 있다. 회로 기본동작원리 및 회로 해석은 무차원화 파라미터를 도입하여 범용성을 부여하여 도식적으로 나타내었다. 음향공명을 제거하기 위해 타이머 IC와 구동 IC로 구성된 간단한 주파수 제어기를 구현하였다. 실험을 통해 복공진 인버터를 적용한 고역률 메탈핼라이드램프용 전자식 안정기가 안정적으로 동작함을 확인하였다

• 한국소음진동공학회논문집
• /
• 제19권5호
• /
• pp.530-536
• /
• 2009

In this paper, the power flow analysis(PFA) has been used to analyze the vibration of a plate covered with a damping sheet. Experiments have been performed to measure the loss factor and frequency response functions of the plate covered with the damping sheet. The data for the loss factor has been used as the input data to predict the vibration of the coupled plates with PFA. The comparison between the experimental results and the predicted PFA results for the frequency response functions has been performed. It showed that PFA can be effectively used to predict structural vibration of a plate covered with a damping sheet in medium-to-high frequency range.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2009년도 춘계학술대회 논문집
• /
• pp.496-497
• /
• 2009

In this paper the power flow finite element method (PFFEM) has been used to analyze the vibration of a plate partially covered with a damping sheet. Experiments have been performed to measure the loss factor and frequency response functions of the plate partially covered with the damping sheet. The data for the loss factor has been used as the input data to predict the vibration of the coupled plates with PFFEM. The comparison between the experimental results and the predicted PFFEM results for the frequency response functions has been performed. It showed that PFFEM can be effectively used to predict structural vibration in medium-to-high frequency ranges.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1995년도 추계학술대회 논문집 학회본부
• /
• pp.246-249
• /
• 1995

This paper proposed a partial resonant swtiching three-phase high power factor converter using a lossless snubber. The proposed converter has a merit of simple controlled circuit because tile input current control discontinuously. And it is improve to input power factor that the snubber capacitor's energy regenerate to the AC source side. This topology is reduced a current/voltage stresses of resonant devices in addition to a partial resonant strategy. The result of simulations with the proposed topology included in this paper.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1995년도 추계학술대회 논문집 학회본부
• /
• pp.255-257
• /
• 1995

Many new electronic products are required to have a unity power factor and a distortion free input current waveform. In this parer, a high performance single phase AC/DC converter with input power factor correction is proposed. And each parameters are determined. Proposed control strategy has many advantages which include two Quadrants operation, simplified control circuit, high performance features and continuous Input current. The experimental results are included to verify the validity of this approach.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 1998년도 Proceedings ICPE 98 1998 International Conference on Power Electronics
• /
• pp.264-269
• /
• 1998

A proposed soft-switching buck-boost PWM converter has a lot of advantages, Viz., electric isolation, a high power factor, low switching losses, low EMI noise, reduction of the voltage and current stresses, etc. In a new PFC converter, the switching device is replaced by the loss-less snubber circuit to achieve the zero voltage switching (ZVS) at the maximum current. However, the charging current of the capacitor in the loss-less snubber circuit distorts the input current waveforms. To improve the input current waveform, a new duty factor control method is proposed in this paper.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2000년도 추계학술대회 논문집 학회본부 B
• /
• pp.368-371
• /
• 2000

Two-stage power factor correction (PFC) converter with a single PWM controller is proposed. It consists of a power factor pre-regulator cascaded by an isolated DC/DC converter as in a conventional two-stage approach. However, a single PWM controller is used as in a single-stage, single-switch PFC approach. This converter gives the goof power factor correction, low line current harmonic distortions, and tight output voltage regulations. This converter also has a high efficiency by employing an soft switching method. The proposed approach has advantages such as high performance over the single-stage approach and low cost over two-stage approach. The experimental results obtained on a 300W (30V/10A) prototype PFC converter are given to verify the effectiveness of the proposed control method.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1994년도 추계학술대회 논문집 학회본부
• /
• pp.135-137
• /
• 1994

It this paper, a single-phase high power factor rectifier with low-enery requirements for filtering elements is proposed. By switching control, the current containing the 3rd-hamonic component is to flow into the rectifier. Properly selecting the amplitude of the 3rd-hamonic component, it is possible to reduce the stored energy in the rectifier. Boost converter is used for power-factor control while active filter absorbs the 3rd-hamonic component. Simulation results are presented to show low stored energy of the proposed rectifier.

• 전력전자학회논문지
• /
• 제3권2호
• /
• pp.131-137
• /
• 1998

태양전지의 출력특성은 일사량, 온도와 부하에 의해 크게 변동하기 때문에 가능한 한 많은 에너지를 얻기 위해서는 태양전지의 출력을 항상 최대로 제어할 필요가 있다. 또한 가정용 부하는 교류부하인 반면에 태양전지의 출력은 직류이므로 태양광 발전 시스템에서는 인버터가 필수적이며, 단위역률을 갖는 정현파 전류 및 전압을 계통에 공급해 주어야 한다. 본 논문에서는 계통연계형 태양광 발전시스템을 승압쵸퍼와 전압형 인버터로 구성하였다. 전력비교에 따른 시비율을 변화시켜 일사량과 온도변화에 관계없이 항상 최대출력점을 추적하도록 승압쵸퍼를 제어하였고, 전압형 인버터는 위상동기를 위해서 계통전압을 검출하여 계통전압과 인버터 출력을 동상 운전하므로 고역률과 저고조파 출력으로 부하와 계통에 전력이 공급되도록 제어하였다.

• 전력전자학회논문지
• /
• 제21권5호
• /
• pp.381-387
• /
• 2016

Many efforts have focused on the improvement of power density and efficiency by downsizing the motor and inverter. Recently, Toyota, Honda, and GM realized that the compact-sized motor uses the hairpin structure with increased space factor. Reducing the maximum torque from high-speed technique also makes it possible to design the high-power density model. Toyota and Honda used the newly developed power semiconductor IGBT to decrease conduction loss for high-efficiency inverter. In particular, Toyota used the boost converter to increase the DC link voltage for high efficiency in low-torque high-speed region. Toyota and GM also used the double-sided cooling structure for miniaturization of inverter for high-power density.