• Journal of the Korean Ceramic Society
• /
• v.40 no.10
• /
• pp.943-948
• /
• 2003

The microstructure and electrical characteristics of Zn-Pr-Co-Cr-Dy oxides-based varistors were investigated with Dy$_2$ $O_3$ content in the range of 0.0∼2.0 ㏖%. As Dy$_2$ $O_3$ content is increased, the average grain size was decreased in the range of 18.2∼4.6 $\mu\textrm{m}$ and the ceramic density was decreased in the range of 5.49∼4.64 g/㎤. The incorporation of Dy$_2$ $O_3$ markedly enhanced the nonlinear properties of varistors more than 9 times in nonlinear exponent, compared with the varistor without Dy$_2$ $O_3$ The varistor with 0.5∼1.0 ㏖% Dy$_2$ $O_3$ exhibited the high nonlinearity, in which the nonlinear exponent is above 55 and the leakage current is below 1.0 ${\mu}\textrm{A}$. The donor concentration and the density of interface states were decreased in the range of (4.66∼0.25)${\times}$10$\^$18//㎤ and (5.70∼1.39)${\times}$10$\^$12//$\textrm{cm}^2$, respectively, with increasing Dy$_2$ $O_3$ content. The minimum dielectric dissipation factor of 0.0023 was obtained for 0.5 ㏖% Dy$_2$ $O_3$, but further addition of Dy$_2$ $O_3$ increased it.

• Korean Journal of Materials Research
• /
• v.22 no.11
• /
• pp.569-574
• /
• 2012

Large single grain $Gd_{1.5}Ba_2Cu_3O_{7-y}$ (Gd1.5) bulk superconductors were fabricated by a top-seeded melt growth (TSMG) process using an $NdBa_2Cu_3O_{7-y}$ seed. The seeded Gd1.5 powder compacts with a diameter of 50 mm were subjected to the heating cycles of a TSMG process. After the TSMG process, the diameter of the single grain Gd1.5 compact was reduced to 43 mm owing to the volume contraction during the heat treatment. The superconducting transition temperature ($T_c$) of the top surface of the single grain Gd1.5 sample was as high as 93.5 K. The critical current densities ($J_cs$) at 77 K and 1T and 1.5 T were in ranges of 25,200-43,900 $A/cm^2$ and 10,000-23,000 $A/cm^2$, respectively. The maximum attractive force at 77 K of the sample field-cooled using an Nd-B-Fe permanent magnet (surface magnetic field of 0. 527 T) was 108.3 N; the maximum repulsive force of the zero field-cooled sample was 262 N. The magnetic flux density of the sample field-cooled at 77 K was 0.311T, which is approximately 85% of the applied magnetic field of 0.375 T. Microstructure investigation showed that many $Gd_2BaCuO_5$ (Gd211) particles of a few ${\mu}m$ in size, which are flux pinning sites of Gd123, were trapped within the $GdBa_2Cu_3O_{7-y}$ (Gd123) grain; unreacted $Ba_3Cu_5O_8$ liquid and Gd211 particles were present near the edge regions of the single grain Gd1.5 bulk compact.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.42 no.5
• /
• pp.689-699
• /
• 2022

Recently, high productivity capabilities have been improved due to the application of advanced technologies in various industries, but in the construction industry, productivity improvements have been relatively low. Research on advanced technology for the construction industry is being conducted quickly to overcome the current low productivity. Among advanced technologies, 3D scan technology is widely used for creating 3D digital terrain models at construction sites. In particular, the 3D digital terrain model provides basic data for construction automation processes, such as earthwork machine guidance and control. The quality of the 3D digital terrain model has a lot of influence not only on the performance and acquisition environment of the 3D scanner, but also on the denoising, registration and merging process, which is a preprocessing process for creating a 3D digital terrain model after acquiring terrain scan data. Therefore, it is necessary to improve the terrain scan data processing performance. This study seeks to solve the problem of density inhomogeneity in terrain scan data that arises during the pre-processing step. The study suggests a 'pixel-based point cloud comparison algorithm' and verifies the performance of the algorithm using terrain scan data obtained at an actual earthwork site.

• Membrane Journal
• /
• v.32 no.4
• /
• pp.253-263
• /
• 2022

This study suggests a guideline for designing unit process of wastewater reuse in terms of a maintenance of the process based on critical parameters to draw a high quality performance of RO unit. Defining the parameters was done by applying membrane integrity test (MIT) in pretreatment process utilizing lab-scale MF. SDI is utilized for judging whether permeate is suitable to RO unit. However, result said TOC concentration matching with particle count analysis is better for judging the permeate condition. When membrane test pressure (P_test) was measured to derive log removal value in PDT, virgin state of membrane fiber was used to measure dynamic contact angle utilizing surface tension of the membrane fiber. Actually, foulant affects to the state of membrane surface, and it decreases the P_test value along with time elapsed. Consequently, LRV_DIT is also affected by P_test value. Thus, sensitivity of direct integrity test descends with result of P_test value change, so P_test value should be considered not the virgin state of the membrane but its current state. Overall, this study focuses on defining design parameters suitable to MF pretreatment for RO process in wastewater reuse by assessing its impact. Therefore, utilities can acknowledge that the membrane surface condition must be considered when users conduct the direct integrity test so that P_test and other relative parameter used to calculate LRV_DIT are adequately measured.

• 한국체육학회지인문사회과학편
• /
• v.55 no.3
• /
• pp.613-626
• /
• 2016

The purpose of this study was to identify the effect of dance sport participation on body composition and cardiometabolic parameters in obese middle aged women, by analyzing the current literature(2005-2015). The data from 9 studies were included in this systematic review and meta-analysis, and Comprehensive Meta Analysis(CMA) Version 2.0 was used for statistical analysis. A total of 197 middle aged women(intervention group: n=98, control group: n=99) were included in this analysis. An average duration of the dance sports intervention was 12.2 weeks, 3.13 session per week and 75 minutes per session. Significant reduction in body weight, body fat percent, triglyceride, low density lipoprotein LDL-Cholesterol and leptin were observed while significant increase in high density lipoprotein HDL-cholesterol was observed after the intervention. There were large effect size in percent body fat, total cholesterol, HDL-cholesterol and LDL-cholesterol while medium and small effect size were observed for triglyceride and body weight, leptin, insulin and glucose, respectively. In conclusion, dance sport participation resulted in positive changes in body composition and cardiometabolic parameter in middle aged women.

• Journal of Plant Biotechnology
• /
• v.42 no.4
• /
• pp.326-335
• /
• 2015

Citrus is an economically important fruit tree with the largest amount of fruit production in the world. It provides important nutrition such as vitamin C and other health-promoting compounds including its unique flavonoids for human health. However, it is classified into the most difficult crops to develop new cultivars through conventional breeding approaches due to its long juvenility and some unique reproductive biological features such as gamete sterility, nucellar embryony, and high level of heterozygosity. Due to global warming and changes in consumer trends, establishing a systematic and efficient breeding programs is highly required for sustainable production of high quality fruits and diversification of cultivars. Recently, reference genome sequences of sweet orange and clementine mandarin have been released. Based on the reference whole-genome sequences, comparative genomics, reference-guided resequencing, and genotyping-by-sequencing for various citrus cultivars and crosses could be performed for the advance of functional genomics and development of traits-related molecular markers. In addition, a full understanding of gene function and gene co-expression networks can be provided through combined analysis of various transcriptome data. Analytic information on whole-genome and transcriptome will provide massive data on polymorphic molecular markers such as SNP, INDEL, and SSR, suggesting that it is possible to construct integrated maps and high-density genetic maps as well as physical maps. In the near future, integrated maps will be useful for map-based precise cloning of genes that are specific to citrus with major agronomic traits to facilitate rapid and efficient marker-assisted selection.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.37 no.2
• /
• pp.159-169
• /
• 2004

Sedimentation and depositional pattern of the fine-grained sediments in the southeastern inner shelf of Korea were studied using a very high-resolution seismic profiles and sediment data. The recent mud deposits up to 45 m thick are distributed in the inner shelf forming a nearshore belt from the eastern part of Geoje Island to off the Pohang along the coast. The sediment in this area consists of homogeneous mud with mean grain size between $8.6\;to\;5.3\phi$ and does not show any distinct variability It gradually becomes finer and well sorted northeastward along the coast. Sediments normally appear as structureless massive mud but X-radiographs show that some bioturbation and faint lamination are present. The sediments accumulate at a rate of 0.18-0.44 cm/yr and the rate coincides well with the long-term (a 1000-year scale) accumulation based on very high-resolution seismic data. Distribution of wet bulk density and velocity shows a gradual increase from the southeastern part of Ulsan to off Pohang, whereas porosity shows a reverse pattern. Correlations between velocity and porosity/mean grain size are different from other regions compared, due to the difference of sediment texture and sedimentary environment. The recent shelf deposits are seismically characterized by three distinct facies: 1) well-stratified (near the river mouth), 2) semi-transparent (eastern part of Geoje Island), and 3) transparent (off Ulsan). The results suggest that fine-grained sediment derived from rivers, forming a nearshore mud belt, have been transported northeastward by the northeastward-flowing coastal current.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.11 no.3
• /
• pp.95-104
• /
• 2007

This study was focused on the effect of concrete strength and lateral ties of concrete columns subjected to eccentric compressive loads. The twenty-four concrete columns with $200mm{\times}200mm$ square cross-section were tested. The main variables were concrete strength, spacing and configuration of lateral ties, and eccentricity ratios. From the experiment, the followings were investigated ; 1) In all cases, it was observed that the increase of concrete compressive strength led to the decrease of ductility. Also, as the eccentricity ratios increased, the effect of ductility enhancement by lateral ties decreased. 2) As the ties spacing decreased from 100mm to 30mm, the magnitude of axial load acting on the concrete column showed an enhancement of 1.1~1.2 times and the descending curve after a peak moment presented a smooth decline. 3) The high-strength concrete columns required a design of lateral ties to increase the volumetric ratios and density of tie spacing to sustain a proper strength and ductility. Accordingly, regardless of concrete strength, the current AIK design code to specify the maximum tie spacing of concrete columns was proven to lead to the poor strength and ductility for seismic design. Therefore, it is necessary to develop a new seismic design code that connects volumetric ratios and tie spacing of concrete columns with concrete strength.

• Journal of Advanced Marine Engineering and Technology
• /
• v.13 no.2
• /
• pp.43-63
• /
• 1989

Various kinds of corrosion prevention methods have been developed. It is known that the method of electrochemical protection is more effective and economical than any other method on the large scale metal structures in corrosive solutions. Strong acid solutions such as nitric and sulfuric acid solutions are often used in industries, and the expensive stainless steel is almost exclusively used for the equipment that comes in contact with such acid solutions. However, it is more reasonable that carbon steel is used rather than stainless steel depending upon concentration of those acid solutions from the economical viewpoint. In this study, the typical strong acid solution such as nitric and sulfuric acid solutions are chosen for the experiment and the selected materials of specimen are the stainless steels of SUS 304L and SUS 316L, the carbon steels of SS 41, SM 50 and RA 32, and highly pure lead. Electrochemical protection diagrams can be drawn with data from the external cathodic and anodic polarization curves of SUS 304L, SUS 316L and SM 50 steels in 5-60% nitric acid solutions and from those polarization curves of SS 41, RA 32, SM 50 and SUS 316L steels, and highly pure lead in 2.5-98% sulfuric acid solutions at the slow scanning rate. The data obtained with using the determination method of the optimum cathodic protection potential, the Tafel extrapolation method and the characteristics of anodic polarization curves. The main results obtained from the diagrams are as follows: 1) In nitric acid solution : (1) Corrosion potentials exist in each of those corrosion zones on the stainless steels in the lower concentration than about 12% solutions and on the high tensile strength steels in the lower concentration than about 30% solutions, but the corrosion current (density) in each zone is small on the above mentioned former steels and large on the latter ones. (2) The stainless steels can be self-passivated in the higher concentration than 15% solutions, and the high tensile strength steels gives rise to the same phenomenon in the higher concentration than 35% solutions. (3) The stainless steels in the lower concentration than 60% solutions and the high tensile strength steels in the higher concentration than 35% solutions can be used without protection, but the latter steels must ve protected anodically in the lower conccentration than about 30% solutions. 2) In sufuric acid solution : (1) The carbon steels can be self-passivated in the higher concentration than 45% solutions, and the SUS 316L steel in higher concentration than 75% solutions and the lead in all concentration solutions also gives rise to the same phenomenon. (2) The lead in the lower concentration than 80% solutions and the SUS 316L steel in the higher concentration than 80% solutions can be used without protection. (3) The carbon steels in the higher concentration than 50% solutions also can be used without protecting economically, but the SUS 316L steel in the 20-70% solutions are considerably corrosive without protecting anodically.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.276-276
• /
• 2010

Localized surface plasmon resonance (LSPR) has been explored recently as a promising approach to increase energy conversion efficiency in photovoltaic devices, particularly for thin film hydrogenated amorphous silicon (a-Si:H) solar cells. The LSPR is frequently excited via an electromagnetic (EM) radiation in proximate metallic nanostructures and its primary con sequences are selective photon extinction and local EM enhancement which gives rise to improved photogeneration of electron-hole (e-h) pairs, and consequently increases photocurrent. In this work, high-dielectric-constant (k) $ZrO_2$ (refractive index n=2.22, dielectric constant $\varepsilon=4.93$ at the wavelength of 550 nm) is proposed as spacing layer to enhance the LSPR for application to the thin film silicon solar cells. Compared to excitation of the LSPR using $SiO_2$ (n=1.46, $\varepsilon=2.13$ at the wavelength of 546.1 nm) spacing layer with Au nanoparticles of the radius of 45nm, that using $ZrO_2$ dielectric shows the advantages of(i) ~2.5 times greater polarizability, (ii) ~3.5 times larger scattering cross-section and ~1.5 times larger absorption cross-section, (iii) 4.5% higher transmission coefficient of the same thickness and (iv) 7.8% greater transmitted electric filed intensity at the same depth. All those results are calculated by Mie theory and Fresnel equations, and simulated by finite-difference time-domain (FDTD) calculations with proper boundary conditions. Red-shifting of the LSPR wavelength using high-k $ZrO_2$ dielectric is also observed according to location of the peak and this is consistent with the other's report. Finally, our experimental results show that variation of short-circuit current density ($J_{sc}$) of the LSPR enhanced a-Si:H solar cell by using the $ZrO_2$ spacing layer is 45.4% higher than that using the $SiO_2$ spacing layer, supporting our calculation and theory.