• Journal of Biosystems Engineering
• /
• v.35 no.5
• /
• pp.302-309
• /
• 2010

Aerial application using an unmanned agricultural helicopter would allow precise and timely spraying. The attitude of a helicopter depends on a number of dynamic variables for roll-balanced flight. Laterally tilting behavior of a helicopter is a physically intrinsic phenomenon while hovering and forwarding. In order to balance the fuselage, the rotor should be counter-tilted, resulting in the biased down-wash. The biased spraying toward right side causes uneven spray pattern. In this study, a raised tail rotor system for the roll-balanced helicopter was studied. Thrust of the tail rotor system was measured and theoretically estimated for the fundamental database of the roll-balanced helicopter design. The estimated tail thrust and roll-moment would be used to design the raising height of tail rotor and roll balancing dynamics. The unmanned agricultural helicopter required the tail rotor thrust of about 39.2 N (4.0 kgf) during hovering with a payload of 235.4 N (24 kgf). A raised tail rotor system would compensate for the physical tilt phenomena. A further attitude control system of helicopter would assist roll-balanced aerial spray application.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.31 no.2
• /
• pp.46-54
• /
• 2023

Helicopter pilots are required to perform many visual workloads in topographical avoidance, flight path modification and navigation, because helicopters operate at very low altitudes. The helicopter-specific instability also require the pilot to have precise perception and control. This has caused frequent human error in helicopter accidents. In Korea, two to three cases have occurred annually on average over the past 10 years, and this trend has not decreased. The purpose of this study was to identify human error risks in advance to prevent helicopter accidents and to help develop measures for missions and mission phases with high risk of human error. Through the study, the tasks and mission phases where accidents occur frequently were classified and the risk of human error was calculated for each mission phases. To this end, the task of frequent accidents during helicopter missions was first identified, detailed steps were classified, and the number of accidents was analyzed. Next, the AHP survey program was developed to measure the pilot's risk of human error and the survey was conducted on the pilots. Finally, the risk of human error by helicopter mission and by mission phases calculated and compared with the actual number of accidents.

• Journal of Biosystems Engineering
• /
• v.37 no.3
• /
• pp.192-200
• /
• 2012

Purpose: Aerial application of chemicals with an agricultural helicopter allows for precise and timely spraying and reduces working labor and pollution. An attitude controller for an agricultural helicopter would be helpful to aerial application operator. The objectives of this paper are to determine the transfer function models and to estimate the handling qualities of a bare-airframe model helicopter. Methods: Transfer functions of a model unmanned helicopter were estimated by using NAVFIT and DERIVID modules of the $CIFER^{(R)}$ program to the time history data of frequency sweep flight tests. Control inputs of the transfer functions were elevator, aileron, rudder and collective pitch stick positions and the outputs were resulting on-axis movements of the fuselage. Results: Minimum realization of the transfer functions for pitch rate output to elevator control input and roll rate output to aileron control input produced second order transfer functions with undamped natural frequencies around 3.0 Hz and damping ratios of 0.139 and 0.530, respectively. The equivalent time delays of the transfer functions ranged from 0.16 to 0.44 second. Sensitivity analysis of the proposed parameters allowed derivation of minimal realization of the transfer functions. Conclusions: Handling quality of the model helicopter was addressed based on the eigenvalues of the transfer functions, corresponding undamped natural frequencies with damping ratios. The equivalent time delays of the lateral-directional motion ranged from 0.16 to 0.44 second, longer than the 0.1 to 0.15 second requirement for well-controlled typical manned aerial vehicles.

• Journal of Institute of Control, Robotics and Systems
• /
• v.7 no.3
• /
• pp.229-237
• /
• 2001

In this paper, we propose two design methods of neural networks controller for the height control of helicopter, one is the design of neural network controller having learning capability and the other is the design of more improved neural network controller. Through the simulation results, we show that the proposed controllers have controllers have enhanced control performance(rapid response, effectiveness and safety) than the typical neural networks controller in the height control of helicopter.

• The Transactions of the Korean Institute of Electrical Engineers D
• /
• v.53 no.6
• /
• pp.433-439
• /
• 2004

The Helicopter Simulator System is non-linear and complex. Futhermore, because of absence of its accurate mathematical model, it is difficult to control accurately its attitudes such as elevation angle and azimuth one. Therefore, we proposed a Hybrid GA-PID WAVENET(Genetic Algorithm Proportional Integral Derivative Wavelet Neural Network)control technique to control efficiently these angles. The proposed Hybrid GA-PID WAVENET is made through the following process. First, the WAVENET fundamental functions are defined. And their dilation and translation values are adjusted by GA to construct the optimal WAVENET controller. Secondly, the proportional, integral, and derivative gain coefficients of PR controller are tuned optimally. Finally, WAVENET controller which has a good transient characteristic and GA-PE controller which has a good steady state characteristic is adequately combined in hybrid type. Through the computer simulations, it is proved that the Hybrid GA-PE WAVENET control technique has a more excellent dynamic response than PID control technique and GA-PID one.

• 제어로봇시스템학회:학술대회논문집
• /
• 2001.10a
• /
• pp.85.6-85
• /
• 2001

This paper describes a 3-DOF attitude control of a small model helicopter in hover through explicit decoupling and adaptive control scheme. A model helicopter mounted on gimbal-stand is considered as a system that has 3 independent SISO systems representing motions about roll, pitch and yaw axis and these subsystems are identified from the test flight data. In this consideration, the contribution of others to yaw channel is neglected since it is relatively small. Two PID controllers based on Ziegler-Nichols method are designed for roll pitch channels independently. Also, adaptive fuzzy tuner is designed and applied to those PID controllers to cope with coupling effects between each channel and system uncertainties due to variation of engine RPM. The experimental results show that the attitude control ...

• International Journal of Control, Automation, and Systems
• /
• v.5 no.1
• /
• pp.24-34
• /
• 2007

Closed-loop active twist control of integral helicopter rotor blades is investigated in this paper for reducing hub vibration induced in forward flight. A four-bladed fully articulated integral twist-actuated rotor system has been designed and tested successfully in wind tunnel in open-loop actuation. The integral twist deformation of the blades is generated using active fiber composite actuators embedded in the composite blade construction. An analytical framework is developed to examine integrally twisted helicopter blades and their aeroelastic behavior during different flight conditions. This aeroelastic model stems from a three-dimensional electroelastic beam formulation with geometrical-exactness, and is coupled with finite-state dynamic inflow aerodynamics. A system identification methodology that assumes a linear periodic system is adopted to estimate the harmonic transfer function of the rotor system. A vibration minimizing controller is designed based on this result, which implements a classical disturbance rejection algorithm with some modifications. Using the established analytical framework, the closed-loop controller is numerically simulated and the hub vibratory load reduction capability is demonstrated.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.13 no.5
• /
• pp.564-570
• /
• 2003

This paper presents an adaptive fuzzy control scheme for nonlinear helicopter system which has uncertainty or unknown variations in parameters. The proposed adaptive fuzzy controller is a model reference adaptive controller. The parameters of fuzzy controller are adjusted so that the plant output tracks the reference model output. It is shown that the adaptive law guarantees the stability of the closed-loop system by using Lyapunov function. Several experiments with a small model helicopter having parameter variations are performed to show the usefulness of the proposed adaptive fuzzy controller.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.33 no.9
• /
• pp.922-929
• /
• 2009

This paper deals with the State-Dependent Riccati Equation (SDRE) Technique for the design of helicopter nonlinear waypoint guidance controller. To generate the flight guidance through multiple waypoints, we use the trigonometric spline. The controller design and its validation is based upon a level 2 simulation helicopter model and the designed SDRE controller is applied to the trajectory tracking problems. To validate the designed SDRE controller, the simulation environment of high fidelity helicopter model is developed using three independent computers. This paper focuses on the validation the present SDRE controller through the helicopter waypoint guidance simulation.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.31 no.10
• /
• pp.1031-1038
• /
• 2007

A study on the development of control loading system for a pilot command in the helicopter flight training device is performed. The key issue of the device is how to provide closely the real feeling of the stick forces to the trainer during the flight training. Focusing on this proviso and considering the suitable approach than the complexity of the hydraulic system, we adopt the AC servo motor system although its inherent disadvantages such as the torque ripple and the stick-slip friction effect at a low control force. However, we overcome these detrimental effects by introducing the appropriate control device and the robust structural design of the actuating system, thereby the feasibility and applicability to the system can be obtained by showing good performance, meeting the required specification.