This study was carried out to estimate the property of dimensional stability of heat compression of italian poplar wood with low density. Firstly, two levels of pressure conditions were applied using the closed and open-press system. The thermal treatment temperatures were 180℃ and 200℃, respectively. Water absorption tests were conducted in water bath at 25℃ and 100℃ for 35 hours and 1 hour, respectively. The compression rates of wood were 47 percent, 60 percent, and 73 percent, respectively. From these tests, it was found that the dimensional stability of the closed-press system was superior to that of the open-press system. Furthermore, the dimensional stability of compressed wood in the closed-press system was better at 200℃ than 180℃. In compression rate, dimensional stability of 73 percent compression rate was the best result. Considering these results, the best conditions for the dimensional stability of compressed wood were those of the closed-compressing system at high temperatures above 200℃ and larger compression rate. Therefore, it was concluded that the dimensional stability of wood is improved at higher temperature and larger deformation.
Ho-Jun Gam;Yosep Kang;Eun-Jung Park;Seong-Heon Kim;Sang-Mo Kang;In-Jung Lee
한국작물학회:학술대회논문집
/
한국작물학회 2022년도 추계학술대회
/
pp.109-109
/
2022
The global population is increasing every year, and the amount of food waste is also increasing. Direct landfilling of food waste has been prohibited since 2005, and in accordance with the London Convention in 2013, the discharge of livestock manure, sewage sludge, and food waste into the sea is prohibited. In the case of incineration to treat the discharged food waste, the heat point is lowered due to the moisture in the food waste itself, so fuel must be added. Therefore, this study was conducted to get basic data for setting the limit of application by investigating the growth and yield of crops after treating food waste dry powder mixed fertilizer (MF) on red pepper. In the experiment, continuous cultivation was carried out for two years in 2021 (1st year) and 2022 (2nd year). The treatment groups were set as Not Treatment (NT), Chemical Fertilizer (CF), Mixed Fertilizer (MF), Mixed Fertilizer×2 (MF×2). After harvest, crop growth and yield were investigated. As a result of the 1st years of growth survey, CF, MF, MF×2 show significant difference in shoot length compared to NT. About fresh weight and dry weight, CF show significant difference compared to NT. The 2nd years of growth survey, the shoot and root length, fresh weight did not show significant difference with NT. In case of dry weight, MF is significant increased compared to NT. As a result of the yield survey of the 1st year, all treatment groups did not show a significance in yield compared to the NT. In case of 2nd year, all treatment groups show significantly increased value compared to NT. The yield of MF was highest among the treatment groups. In the future, it is thought that it is necessary to quantitatively evaluate the effect of food waste dry powder mixed fertilizer through additional experiments and continuous cultivation, and to establish an appropriate amount of use and establishment of a manual based on this.
Experiments were carried out for the development of a processing method of soybean into full-fat or defatted flour, using two varieties of soybean (kwangkyo produced in Korea and Bragg produced in India) Samples were subjected to dry dehulling, size reduction and wet heat treatment processes to make soybean flours. The quality of soybean flours were evaluated, and the results obtained were summarized as follows. 1. Crude fiber content of dehulled soybean was under 3.0% which indicated satisfactory dehulling, and there was no significant difference in crude fibre content between two varieties. 2. When dehulled soybean was cracked into soy grits by a hammer mill, 98.71∼98.86% of the soy grit was in the range of 10∼18 mesh which was the optimum size of particle for quick and uniform penetration of heat into the intra-particle air spaces. 3. Moisture content of soy flour after steam treatment at 15 psig for 5 to 30 min was only 0.29∼1.68% which did not hinder the next milling operation. 4. From the color analysis of soy flours, it was observed that the dominant wavelength for all the samples are in a very narrow range from 575 to 581 nm and the color variation was from yellow to yellowish orange. Twenty to twenty five % higher reflectance was observed in the defatted flours than full fat flours. The % chroma of the defatted flour slightly increased as the duration of steaming of soy grits increased, whereas that of the full-fat flour did not. 5. The protein extractability in the defatted flour at pH 7.6 showed progressive decrease in solubility from 48.40% (Bragg), 75.20% (kwangkyo) for untreated flours to 9.75% (Bragg), 26.27% (kwangkyo) for 30 min steaming. But Kwangkyo variety showed twice higher protein extractability than Bragg variety.
옥수수 전분(초기 수분함량 11.4%)을 $130{\sim}220^{\circ}C$에서 건열처리하여 DSC로 열분석한 결과 $190^{\circ}C$이상에서 호화엔탈피는 감소하였고 알칼리호화시 열처리온도가 상승할수록 점도가 증가하였다. $170^{\circ}C$이상에서 열처리 온도가 높아질수록 원료전분에 비하여 최고점도를 포함한 아밀로그램상의 모든 값들, 전분호화액의 전단응력과 겉보기점도, 점조도지수 및 항복응력은 감소하였다. $90^{\circ}C$에서 호화진행에 따라 모든 시료들의 겉보기 점도와 항복응력은 상당히 증가하였으며 $190^{\circ}C$시료는 특히 초기에 급증하였으나, 점조도지수는 약간 증가한 반면에, 유동거동지수값들은 큰 차이를 보이지않았다. 그러나 $220^{\circ}C$의 경우 모든 값들이 다른 시료들에 비하여 크게 낮았다.
In order to investigate different and original theories on pathology of eyes from the past main etiology of fire and heat, two texts of Si-sheng-xin-yuan written by Huang Yuan Yu and Eui-gam-jung-ma written by Lee Gyu Jun are selected and analysed in terms of pathology and prescription. Huang explained that diseases of the eyes are usually born of functional disorders of spleen and stomach(脾胃升降失調) accompanied with turbidity change of energy and blood(氣血淸濁變化). In the meantime, Lee described that the diseases are made from disorders of activities of essence, spirit, energy and blood stored in 5 viscera. So following them, the main point of treatment for the diseases of eyes is to restore and clarify the stagnated gastrointestinal(GI) function, or to supply the clear essence and blood to eyes respectively. Also they have same opinions that the fire and heat are the secondary symptoms of the optical diseases. Therefore Huang focused on cleaning the phlegm and leaking the moisture of GI tract to treat those symptoms, and Lee emphasized on nourishing essential energy of kidney and liver on the other hand. Although they preferred to use radical therapy than symptomatic one. But it can be deduced that Huang's theory is more positive and direct therapy and Lee's one is more basic but indirect treatment.
This study was conducted to investigate the efficacy of surface spraying of antimicrobial solutions, oil and application of both on performance of broiler chicken under heat stress and reared on leaves and ground corn cobs as two alternative bedding materials. Six hundred seventy five day-old straightrun Arian broiler chicks were randomly assigned to 45 pens (at density of $0.09m^2/bird$) in an open sided partially-controlled shed. Three bedding materials viz. wood shavings (WS), ground corn cobs (GCC) (1.5 cm in length) and leaves were subjected to surface spraying of oil ($0.4L/m^2$ animal food grade sunflower oil), anti microbial solutions (3%) and mix treatment of both. Data on performance traits, incidence of breast and food pad lesions and litter characteristics were gathered and analysed in an appropriate factorial arrangements. Body weight at 56 d, feed intake up to 14 d, litter moisture at 28 d, litter pH at 14 d and litter temperature at 14 and 56 d were significantly influenced by litter type (p<0.05). Litter treatment revealed significant impact on body weight at 28, 42 and 56 d, feed intake during 29-42 and 1-42 d, mortality up to 56 d, litter temperature at 28 and 56 d, and litter pH at 28 and 56 d. Leaves and ground corn cobs have shown good potential as alternative bedding materials for rearing broilers. Surface spraying of antimicrobial solutions, oil and applying both were not effective tools to promote the broiler's health and performance. Meat type poultry growers and integrators are considered as primary audiences of the results achieved.
The use of biogas is an industrially necessary means to achieve resource circulation. However, since biogas obtained from waste frequently causes corrosion in pipes, it is important to elucidate corrosion mechanisms of the pipes used for biogas transportation. Recently, corrosion failure occurred in a pipe which supplied for the biogas at the speed of 12.5 m/s. Pinholes and pits were found in a straight line along the seamline of the pipe. By using corrosion-damaged samples, residual thickness, microstructure, and composition of oxide film and inclusion were examined to analyze the cause of the failure. It was revealed that the thickness reduction of biogas pipe was ~0.11 mm per year. A thin sulfuric acid film was formed on the surface of the interior of a pipe due to moisture and hydrogen sulfide contained in a biogas. Near the seamline, microstructure was heterogeneous and manganese sulfide (MnS) was found. Pits were generated by micro-galvanic corrosion between the manganese sulfide and the matrix in the interior of the pipe along the seamline. In addition, microcracks formed along the grain boundaries beneath the pits revealed that hydrogen-induced cracking (HIC) also contributed to accelerating the pitting corrosion.
An experimental work was conducted to develop an optimum operating system of various hay drying systems ; sun-drying with long hay, sun-drying after chopping, sun-drying after crushing, heated air drying after chopping using batch-type dryer and heated air drying after crushing using tunnel-type dryer. Seombody having 60 cm long and initial moisture content of approximately 79 % in wet basis was used for the experiment. The criteria selected for determining the optimum operating condition were the drying performance rate, the production cost and quality of dried matter of each drying systems. The result of this study are summarized as follows : 1. Drying characteristics of leaves of long stem hay, chopped seombody and crushed one were obtained by maintaining the oven temperature at 70 degrees centigrade. The required drying times for various samples to approximately 15% moisture content in wet basis were about 50 min .for leaves ; 160 min. for crushed hay ; 250 min. for chopped hay ; 340min. for ling hay and more than 360 min .for stems. The drying time of crushed hay was required about 50 % of that for the uncrushed long hay. Such a significant difference of drying of time between the leaf and long stem may indicate that an effective drying of seombody may not be achieved unless any kind of special process treatment for the whole hay is undertaken. 2. In each individual drying system, the following conclusions were drawn: a. After 8 days sun-drying on concrete floor under good days with average tempe?rature at $256{\circ}C$ and relative humidity at 55% at 2 P.M., the moisture content of long hay was still above 25 5'~ and the leaf loss during drying caused by wind and rough handling was more than 50 ~G. b. It was possible to dry the chopped seombody by sun-drying down to about 10 % moisture content within 5 days, however, a stock of heat and discolouration phenomena were observed during the drying, which may be due to the increased deposit-density by chopping, resulting in lowering the quality of the dried product. c. Sun-drying for the crushed material by hay-conditioner was required about 4 days to reduce the moisture content to about 10 %, keeping the quality of dried product at good grade. o. The optimum deposit-depth of the chopped seombody in the batch-type dryer used was about 28cm with about 42kg/hr of drying performance rate. However, it was necessary to overturn the materials between the upper and lower layers in order to obtain a good quality of dried product. d. The drying performance rate by the tunnel-type drier was highest among those of drying systems tested, giving the rate of approximately 400kg/day. 3. On reviewing the individual drying system for seombody, it was possible to draw conclusion that the best system was tunnel drying with the crushed seombody as far as the performance rate was concerned. However, the methods gives the highest operational cost. The system for the lowest operational cost with good quality of dried product was the sun-drying with the crushed material. Accordingly, it may be recommended that the system of sun-drying for the crushed seombody may be the most feasible system presently applicable to farm-level operation.
An experimental work was conducted to develop an optimum operating system of various hay drying systems ; sun-drying with long hay, sun-drying after chopping, sun-drying after crushing, heated air drying after chopping using batch-type dryer and heated air drying after crushing using tunnel-type dryer. Seombody having 60 cm long and initial moisture content of approximately 79 % in wet basis was used for the experiment. The criteria selected for determining the optimum operating condition were the drying performance rate, the production cost and quality of dried matter of each drying systems. The result of this study are summarized as follows : 1. Drying characteristics of leaves of long stem hay, chopped seombody and crushed one were obtained by maintaining the oven temperature at 70 degrees centigrade. The required drying times for various samples to approximately 15% moisture content in wet basis were about 50 min .for leaves ; 160 min. for crushed hay ; 250 min. for chopped hay ; 340min. for ling hay and more than 360 min .for stems. The drying time of crushed hay was required about 50 % of that for the uncrushed long hay. Such a significant difference of drying of time between the leaf and long stem may indicate that an effective drying of seombody may not be achieved unless any kind of special process treatment for the whole hay is undertaken. 2. In each individual drying system, the following conclusions were drawn: a. After 8 days sun-drying on concrete floor under good days with average tempe\ulcornerrature at $256{\circ}C$ and relative humidity at 55% at 2 P.M., the moisture content of long hay was still above 25 5'~ and the leaf loss during drying caused by wind and rough handling was more than 50 ~G. b. It was possible to dry the chopped seombody by sun-drying down to about 10 % moisture content within 5 days, however, a stock of heat and discolouration phenomena were observed during the drying, which may be due to the increased deposit-density by chopping, resulting in lowering the quality of the dried product. c. Sun-drying for the crushed material by hay-conditioner was required about 4 days to reduce the moisture content to about 10 %, keeping the quality of dried product at good grade. o. The optimum deposit-depth of the chopped seombody in the batch-type dryer used was about 28cm with about 42kg/hr of drying performance rate. However, it was necessary to overturn the materials between the upper and lower layers in order to obtain a good quality of dried product. d. The drying performance rate by the tunnel-type drier was highest among those of drying systems tested, giving the rate of approximately 400kg/day. 3. On reviewing the individual drying system for seombody, it was possible to draw conclusion that the best system was tunnel drying with the crushed seombody as far as the performance rate was concerned. However, the methods gives the highest operational cost. The system for the lowest operational cost with good quality of dried product was the sun-drying with the crushed material. Accordingly, it may be recommended that the system of sun-drying for the crushed seombody may be the most feasible system presently applicable to farm-level operation.
삼나무의 심재 부위에는 흑화현상이 자주 발생한다. 심재 내 페놀성 추출물과 Norlignans 물질이 약알칼리하에서 산화함으로써 흑화현상이 발생한다고 보고된 바 있다. 본 연구에서는 삼나무 내부 흑심재와 변재간의 색상차를 줄여보고자 열처리와 광처리를 실시하였다. 열처리로는 열기건조, 진공가열건조, 열수처리를 적용하였고, 광처리로는 삼나무 표면에 자외선광을 조사하였다. 열처리와 광처리에서 온도와 함수율 및 자외선의 색상차 감소효과를 평가하였다. 색상차 감소 효과는 열수처리가 가장 우수하였으며, 산소량이 적은 저기압 상태에서 건조시킴으로써 산화반응을 줄여보고자 실시한 진공건조는 기대한 바와 달리 열기건조와 비슷한 정도의 목재 표면의 색상차 감소효과를 보였다. 광처리는 건조재 표면의 색상차 감소효과를 보여 대패가공 후 마감처리에 적합한 것으로 판단된다. 추후 효과적인 삼나무 재색제어를 위해서 각 처리별 최적 공정조건 탐색 및 복합처리 적용기술개발이 필요하다.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.