• 제목/요약/키워드: heat storage rate

검색결과 325건 처리시간 0.024초

Development of Model to Evaluate Thermal Fluid Flow Around a Submerged Transportation Cask of Spent Nuclear Fuel in the Deep Sea

  • Guhyeon Jeong;Sungyeon Kim;Sanghoon Lee
    • 방사성폐기물학회지
    • /
    • 제20권4호
    • /
    • pp.411-428
    • /
    • 2022
  • Given the domestic situation, all nuclear power plants are located at the seaside, where interim storage sites are also likely to be located and maritime transportation is considered inevitable. Currently, Korea does not have an independently developed maritime transportation risk assessment code, and no research has been conducted to evaluate the release rate of radioactive waste from a submerged transportation cask in the sea. Therefore, secure technology is necessary to assess the impact of immersion accidents and establish a regulatory framework to assess, mitigate, and prevent maritime transportation accidents causing serious radiological consequences. The flow rate through a gap in a containment boundary should be calculated to determine the accurate release rate of radionuclides. The fluid flow through the micro-scale gap can be evaluated by combining the flow inside and outside the transportation cask. In this study, detailed computational fluid dynamic and simplified models are constructed to evaluate the internal flow in a transportation cask and to capture the flow and heat transfer around the transportation cask in the sea, respectively. In the future, fluid flow through the gap will be evaluated by coupling the models developed in this study.

열교환기 형상이 축소한 IRWST 내부의 풀핵비등에 미치는 복합적인 영향에 대한 실험적 연구 (Experimental Investigation of the Combined Effects of Heat Exchanger Geometries on Nucleate Pool Boiling Heat Transfer in a Scaled IRWST)

  • Kang, Myeong-Gie;Chun, Moon-Hyun
    • Nuclear Engineering and Technology
    • /
    • 제28권1호
    • /
    • pp.1-16
    • /
    • 1996
  • 축소한 격납용기 내부 핵연료재장전수저장탱크의 안쪽에 설치한 열교환기 튜브의 주요 매개변수들이 풀핵비등 열전달에 미치는 복합적인 영향을 극명하기 위해 튜브 외경, 표면 거칠기, 그리고 튜브 설치 방향에 대한 다양한 조합들을 환용하여 열유속 q'quot;와 과열 온도 차이 $\Delta$T 간의 관계에 대한 총 1,966 개의 실험값을 취득하였다. 이 실험 결과들에 의하면, (1) 표면 거칠기 증가는 수평 및 수직 튜브 모두에 대해 열전달을 향상시키고, (2) 기포 생성에 따른 두가지 열전달 기구인 주변 액체 운동증가에 의한 열전달 향상과 기포층 및 기포 군집 형성에 의한 열전달 감소는 50㎾/$m^2$의 열유속을 경계로 낮은 열유속과 높은 열유속 영 역 에서 서로 다르게 관찰되는데, 이것은 튜브 설치 방향과 표면 거칠기의 크기와 관련이 있으며, (3) 튜브 외경 증가는 수평 및 수직 튜브 모두에 대해 열전달을 감소시키는데, 그 영향정도는 수평보다 수직구조에서 더 크다. 수평 및 수직 튜브들에 대해 열유속 q'quot;와 표면 거칠기 ($\varepsilon$) 및 튜브 외경 (D) 사이의 관계를 결정하는 두 가지 실험식을 개발하였다. 그리고, q'quot;만의 함수로된 풀핵비등 열전달계수( $h_{b}$ 에 대한 간단한 실험식도 부가적으로 개발하였다. 실험식도 부가적으로 개발하였다.'quot;만의 함수로된 풀핵비등 열전달계수($h_{b}$ 에 대한 간단한 실험식도 부가적으로 개발하였다.

  • PDF

상부 코일히터를 갖춘 나선재킷형 태양열 축열조의 성능예측을 위한 CFD 해석모델 개발 및 검증 (Computational Fluid Dynamics Model for Solar Thermal Storage Tanks with Helical Jacket Heater and Upper Spiral Coil Heater)

  • 백승만;종일명;남진현;정재동;홍희기
    • 대한기계학회논문집B
    • /
    • 제37권4호
    • /
    • pp.331-341
    • /
    • 2013
  • 태양열 온수급탕 시스템에서는 태양열 에너지가 집열판에서 획득되고 열매체로 전달되어 최종적으로 온수의 형태로 축열조에 저장된다. 본 연구에서는 상부 코일히터를 갖춘 나선재킷형 축열조의 축열성능 특성을 정확하게 해석할 수 있는 전산유체역학 모델을 개발하였다. 본 연구에서 고려한 축열조는 벽면에 열매체의 나선유로가 형성된 맨틀형 축열조의 일종으로 시스템 설계 단순화, 저유량 운전, 성층화 촉진 등의 장점을 지닌다. 또한 축열조 내부에 추가적인 코일히터가 장착되어 축열성능과 성층화의 추가적인 향상을 도모할 수 있다. 본 연구에서 개발된 해석모델의 검증은 실제 태양열 온수급탕 시스템의 실증실험 결과와 비교를 통하여 수행되었으며, 온수의 온도변화, 열매체의 온도변화, 성층화 온도분포의 측면에서 잘 일치하는 결과를 얻었다.

참다래 쥬스의 이화학적 특성에 미치는 살균 및 저장온도의 영향 (Effects of Pasteurization and Storage Temperatures on the Physicochemical Characteristics of Kiwi Juice)

  • 이진원;김인환;이광원;이철
    • 한국식품과학회지
    • /
    • 제35권4호
    • /
    • pp.628-634
    • /
    • 2003
  • 본 실험은 다양한 온도에서 살균 및 저장함에 따라 참다래 쥬스의 품질에 미치는 영향을 알아보기 위하여 참다래 쥬스$(13.5^{\circ}Brix)$를 65, 75 및 $85^{\circ}C$에서 각각 15초간 살균한 뒤 4, $25^{\circ}C$의 incubator에서 30일간 저장하며, 미생물, 이화학적 특성을 조사한 결과, 대부분의 참다래 쥬스 내 세균은 $65^{\circ}C$의 가열에서 파괴되었고 저장기간 중 모든 시료에 대하여 세균 증식은 나타나지 않았다. Tubular type가열 살균기에서 살균한 참다래 쥬스 중 세균에 대한 D value는 $65^{\circ}C$에서 4.17초, $75^{\circ}C$에서 1.47초, $85^{\circ}C$에서는 0.81초로 감소하였다. Vitamin C함량의 변화는 살균온도와 저장온도 및 저장기간이 증가할수록 감소되었으며, 환원당 함량은 모든 살균조건에서 저장 20일째 최대값을 보인 후, 급격히 감소하는 경향을 나타내었다. 색도의 경우에는 모든 살균 및 저장조건에서 L, a 및 b값은 저장기간에 따라 감소하는 경향을 나타내었으며, 갈색도 변화는 저장기간이 길어질수록 지속적인 감소현상을 나타내었다.

황금 GAP 지침 설정을 위한 건조방법, 저장조건 및 포장재료에 따른 품질변화 (Changes in Quality by Drying Methods, Different Storage Conditions and Package Mediums for Established GAP Guide Book in Scutellaria baicalensis Georgi)

  • 김명석;김길자;최진경;권오도;박흥규;김현우;김성일;김영국;차선우;심재한
    • 한국약용작물학회지
    • /
    • 제25권2호
    • /
    • pp.89-94
    • /
    • 2017
  • Background: The purpose of improving the quality of oriental medicinal herbs is to contribute to the improvement of the income of farm. The present study investigated the effect of reasonable drying methods, different storage conditions and packageing materials on quality and stability of Scutellaria baicalensis Georgi and for developing GAP (good agricultural practice) guide book. Methods and Results: Three methods of drying Scutellaria baicalensis roots produced over two years were used to estimate loss rate owing to drying, storage, and packaging. The methods of drying were categorized into natural drying (36 - 60 h by sunshine), drying with heat dryer (2 - 10 h), or drying with gas bulk dryer (2 - 10 h). After cleaning, and initial drying for a few days under controlled temperature conditions, the second phase of drying was carried out at 35, 45 and $55^{\circ}C$. Changes in hunter color values and quality under the two studied storage treatments (at $20^{\circ}C$ indoors and at $4^{\circ}C$ in a refigerator) were evaluated. Storage period for 60, 120, and 180 days in three packaging materials, PE (polyethylene package), PP (polypropylene gunnysack), and WP (watertight packing paper) were studied. Conclusions: Initial cleaning, reasonable gas drying and hot air drying, and drying in an oven at 35 and $45^{\circ}C$ after cutting the roots resulted in the lowest loss rates in S. Baicalensis root. Hunter color valuse indicated that stroage of dry roots at room temperature was better than PP packaging, and that cold stroage was better than PE packaging for long-term stability.

농산물(農産物) 건조(乾燥)를 위(爲)한 태양열(太陽熱) 집열기(集熱機)의 제작(製作) 및 이용(利用)에 관(關)한 연구(硏究) (Design and Utilization of Solar Collector for Drying Agricultural Products)

  • 고학균;금동혁
    • Journal of Biosystems Engineering
    • /
    • 제6권2호
    • /
    • pp.48-57
    • /
    • 1982
  • In order to improve the quality of traditionally sun-dried red peppers and to increase the efficiency of drying performance, three types of solar dryers were designed and built, and drying performance of the solar dryers was compared to traditional sun drying. Results obtained from the experiment are summarized as fallows: 1. The air temperature and relative humidity profiles over a 8-hour period measured at the specified locations in the drying chamber of solar dryers appeared to have large variation in each dryer. The rate of drying increased with the temperature rise in the drying chamber of the solar dryer. 2. In general. drying with solar dryers proceeded faster than traditional sun drying. With A'-type of solar dryer developed in the second experiment it was possible to dry red peppers in seven days from an initial moisture content of 80% to safe storage conditions. The drying time with the A'-type solar drier was 50% shorter compared to traditional sun drying. 3. Red peppers appeared to have an increasing or constant-rate drying period until the weight of the product was reduced to about one half the initial weight, followed by a falling-rate drying period. When the dried red peppers were exposed to the atmospere during the night, the moisture content increased as much as 6%, which is much higher than for the grains. 4. It was suggested from the experiment that either a heat storage system or a supplemental heating system in the solar dryer was desirable for more efficient drying operation. 5. It was shown that the solar dryer developed in this study may be suitable for drying other vegetables and fishes, and also offered additional advantages of saving in drying time, maintaining sanitation and minimizing contamination by dust, insects and unfavorable weather condition.

  • PDF

액체수소 제조를 위한 냉각튜브 내 유동장 해석 (Analysis on Fluid Dynamics in the Cooling Tube for Manufacture of Liquid Hydrogen)

  • 이대원;홍하이응우엔;나소노바 안나;오인환;김교선
    • 한국수소및신에너지학회논문집
    • /
    • 제26권4호
    • /
    • pp.301-307
    • /
    • 2015
  • We present a study of hydrogen liquefaction using the CFD (Computational Fluid Dynamics) program. Liquid hydrogen has been evaluated as the best storage method because of high energy per unit mass than gas hydrogen, but efficient hydrogen liquefaction and storage are needed in order to apply actual industrial. In this study, we use the CFD program that apply navier-stokes equation. A hydrogen is cooled by heat transfer with the while passing gas hydrogen through Cu tube. We change diameter and flow rate and observe a change of the temperature and flow rate of gas hydrogen passing through Cu tube. As a result of, less flow rate and larger diameter are confirmed that liquefaction is more well. Ultimately, When we simulate the hydrogen liquefaction by using CFD program, and find optimum results, it is expected to contribute to the more effective and economical aspects such as time and cost.

우드펠릿의 저장량에 따른 발화온도 및 발화유도시간에 관한 연구 (A Study on the Ignition Temperature and Ignition Induction Time According to Storage Amount of Wood Pellets)

  • 김형석;최유정;김정훈;정필훈;최재욱
    • 한국화재소방학회논문지
    • /
    • 제33권1호
    • /
    • pp.7-14
    • /
    • 2019
  • 우드펠릿은 화력발전소 및 화목 보일러의 연료로 많이 사용되고 있으나 발열량이 높은 우드펠릿을 장기간 보관 시 자연발화의 위험성이 있다. 본 연구에서는 시료 용기의 크기에 따라 유량의 변화에 따른 최소자연발화온도와 발화한계온도를 구하였으며, 발화한계온도를 이용하여 겉보기 활성화 에너지를 측정함으로써 우드펠릿의 발화 특성을 예측하였다. 겉보기 활성화 에너지는 190.224 kJ/mol을 구하였다. 용기에 저장된 시료량이 두꺼워질수록 시료 표면에서 중심까지의 열전달이 어려워 발화유도시간이 긴 것으로 나타났으며, 용기의 크기가 같을 경우 유량의 양이 많아 질수록 자연발화온도는 낮아졌다. 또한 시료용기가 커질수록 자연발화온도는 낮아지고 발화유도시간은 길어지는 것으로 나타났다.

수소 저장용 탱크의 튜브 형상에 따른 온도분포 특성에 대한 수치해석 연구 (A Study on the Characteristics of Temperature Distribution Related to Geometry of Tube in Hydrogen Storage Vessel)

  • 오승준;윤정환;전경숙;김재규;박준홍;최정주
    • 한국수소및신에너지학회논문집
    • /
    • 제32권4호
    • /
    • pp.205-211
    • /
    • 2021
  • Recently, it is necessary for study on renewable energy due to environmental pollution and fossil fuel depletion. Therefore, in this study, the filling temperature according to the nozzle geometry was evaluated based on the limit temperature specified in SAEJ2601 for charging hydrogen, a new energy. There are three types of nozzles, normal, angle and round, fixed the average pressure ramp rate at 52.5 MPa/min, and the injection temperature was set at 293.4 K. As a result, the lowest temperature distribution was found in the round type, although the final temperature did not differ significantly in the three types of nozzles. In addition, Pearson's coefficient was calculated to correlate the mass flow rate with the heat transfer rate at the inner liner wall, which resulted in a strong linear relationship of 0.98 or higher.

Effects of Clothing Material Dyed with Astringent Persimmon Extract upon Exercise-Induced Thermal Strain and Sensory Responses in a Warm Environment

  • Park, Shin-Jung;Shin, Hye-Sun;Chung, Hee-Chung
    • International Journal of Human Ecology
    • /
    • 제16권2호
    • /
    • pp.1-9
    • /
    • 2015
  • This study investigated the effects of persimmon-dyed clothing materials upon thermophysiological responses and subjective comfort sensations during exercise and rest in a warm environment. Six healthy, untrained women participated in two separate testing sessions, with cotton materials dyed with astringent persimmon extract (DC) and undyed cotton materials (UDC). The physical characteristics associated with heat and moisture transfer were improved in DC; also, stiffness, anti-drapery stiffness and crispness in the primary hand values were higher in DC. The experimental protocol consisted of a 10-min rest, 15-min exercise on a treadmill (at ${7km{\cdot}h^{-1}}$) and 25-min recovery at $28{\pm}0.2^{\circ}C$ and $50{\pm}3%\;RH$. The results were as follows: When wearing DC rather than UDC, mean body temperature, heart rate, heat storage and body mass loss were significantly lower during the whole experimental period. Clothing microclimate temperature showed different profiles between the two clothing materials, being lower with DC than UDC during the first half of exercise and the second half of recovery. Clothing microclimate humidity was significantly lower with DC than UDC during the whole experimental period. When wearing UDC, subjects felt significantly warmer and less comfortable during exercise, and sensed greater humidity during exercise and recovery. These results suggest that eco-friendly clothing materials dyed with astringent persimmon extract can reduce exercise-induced heat load and improve subjective sensations when exercising and resting in a warm environment, due to greater heat dissipation from the body to the outside environment compared with undyed clothing materials.