• Journal of Institute of Control, Robotics and Systems
• /
• v.11 no.8
• /
• pp.726-732
• /
• 2005

This paper proposes an autolanding guidance and control algorithm with the lateral guidance law. This algorithm is basically formulated and designed in feedback linearization based on singular perturbation. Main features of this algorithm are two facts. One of those is that when a certain situation happens that airplane must realign to the runway suddenly assigned due to unexpected environment change around the landing site, the heading guidance in this algorithm is very valuable, and the other is the fact that the inner loop control of this algorithm is able to be designed directly based on the Handling Quality Requirements that most flight control systems must be satisfied with. To illustrate the potential of this algorithm, 6-DOF nonlinear simulation based on the nonlinear airplane model shown in Ref.[11] is carried out. The simulation results showed that the altitude response to the given landing trajectory is accurate, and the airplane heading alignment to the assigned runway from the lateral deviation is successful. It is noted that this algorithm is also applicable to unmanned aerial vehicle, which can be retrieved in autolanding technique, where the runway far retrieving the vehicle is in any direction for example at war field.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.59 no.2
• /
• pp.135-144
• /
• 2023

In order to provide basic data to increase the efficiency and stability of seamanship at anchoring, the characteristics of the hull motion including dragging anchor due to external forces were observed at Mokpo and Jinhae anchorage for the avoidance of the typhoon. As a result, it is necessary to check the embedding motion and holding power of the anchor according to at initial position to decrease dragging anchor. Dragging anchor at anchorage seems to have been easily caused according to discrepancy between embedded anchor flukes and the towing direction due to the change in wind direction, rather than the wind speed. This discrepancy, thus, should be considered when anchoring. This test vessel with a small radius of curvature of the stem is relatively vulnerable to the influence of wind direction and wind speed, so it is easy to cause a decrease in the holding power due to an increase in the rate of turn. When the current speed is greater than or equal to 1 knot, the range of the rate of turn is reduced resulting in a relatively increased holding power. In addition, during the swing, the tension of the chain was high according to the angular velocity change of heading at three-quarters of the swing length rather than the left and right ends.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.18 no.5
• /
• pp.624-631
• /
• 2008

This paper presents a method for a mobile robot to follow a moving object in real time. The robot follows a target object keeping the facing angle toward the target and the distance to the target to given value. The method consists of two procedures: first, the detection of target position in the robot coordinate system, and the second, the calculation of translational velocity and rotational velocity to follow the object:. To detect the target location, range sensor data is represented in histogram. Based on the real time calculation of the location of the target relative to the robot, translational velocity and rotational velocity to follow the target are calculated. The velocities make the heading angle and the distance to target converge toward the desired ones. The performance of the method is tested through simulation. In the simulation, the target moves with three different trajectories, straight line trajectory, rectangular trajectory, and circular trajectory. As shown in the results, it is inevitable to lose track temporarily of the target when the target suddenly changes its motion direction. Nevertheless, the robot speeds up to catch up and finally succeeds to follow the target as soon as possible even in this case. The proposed method can also be utilized to coordinate the motion of multiple robots to keep their formation as well as to follow a target.

• Journal of Institute of Control, Robotics and Systems
• /
• v.21 no.6
• /
• pp.497-502
• /
• 2015

One of the goals in the field of mobile robotics is the development of personal service robots for the elderly which behave in populated environments. In this paper, we describe a security robot system and ongoing research results that minimize the risk of the elderly and the infirm to access an area to enter restricted areas with high potential for falls, such as stairs, steps, and wet floors. The proposed robot system surveys a potential falling area with an equipped laser scanner sensor. When it detects walking in elderly or infirm patients who in restricted areas, the robot calculates the velocity vector, plans its own path to forestall the patient in order to prevent them from heading to the restricted area and starts to move along the estimated trajectory. The walking human is assumed to be a point-object and projected onto a scanning plane to form a geometrical constraint equation that provides position data of the human based on the kinematics of the mobile robot. While moving, the robot continues these processes in order to adapt to the changing situation. After arriving at an opposite position to the human's walking direction, the robot advises them to change course. The simulation and experimental results of estimating and tracking of the human in the wrong direction with the mobile robot are presented.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.25 no.1
• /
• pp.48-56
• /
• 2015

In the paper, a smartphone-controlled personal mobility system(PMS) based on a compass sensor is developed. The use of a magnetic compass sensor makes the PMS move according to the heading direction of a smartphone controlled by a rider. The proposed smartphone-controlled PMS allows more intuitive interface than PMS controlled by pushing a button. As well, the magnetic compass sensor makes a role in compensating for the mechanical characteristics of motors mounted on the PMS. For adequate control of the robot, two methods: absolute and relative direction methods based on the magnetic compass sensor and wireless communication are presented. Experimental results show that the PMS is conveniently and effectively controlled by the proposed two methods.

• 제어로봇시스템학회:학술대회논문집
• /
• 2000.10a
• /
• pp.80-80
• /
• 2000

The GPS can provide accurate position information on the earth. But GPS receiver can't give position information inside buildings. DR(Dead-Reckoning) or INS(Inertial Navigation System) gives position information continuously indoors as well as outdoors, because they do not depend on the external navigation information. But in general, the inertial sensors severely suffer from their drift errors, the error of these navigation system increases with time. GPS and DR sensors can be integrated together with Kalman filter to overcome these problems. In this paper, we developed a personal navigation system which can be carried by person, using GPS and electronic pedometer. The person's footstep is detected by an accelerometer installed in vertical direction and the direction of movement is sensed by gyroscope and magnetic compass. In this case the step size is varying with person and changing with circumstance, so determining step size is the problem. In order to calculate the step size of detected footstep, the neural network method is used. The teaming pattern of the neural network is determined by human walking pattern data provided by 3-axis accelerometer and gyroscope. We can calculate person's location with displacement and heading from this information. And this neural network method that calculates step size gives more improved position information better than fixed step size.

• The Bulletin of The Korean Astronomical Society
• /
• v.36 no.2
• /
• pp.80.2-80.2
• /
• 2011

The sudden decrease of galactic cosmic ray (GCR) intensity observed by ground neutron monitor (NM) is called a Forbush decrease (FD) event. The intensity time profile of FD event looks like the geomagnetic storm visualized by geomagnetic storm index Dst. Oh et al. [2008] and Oh and Yi [2009] classified the FD events into two kinds by criteria of the overlapping simultaneity of main phase in universal time (UT). The FD event is defined simultaneous if the main phase parts observed by the stations distributed evenly around the Earth are overlapped in UT and non-simultaneous if ones are overlapped in each station's local time (LT). They suggested the occurrence mechanisms of two kind FD events related to the interplanetary magnetic structures such as the interplanetary shock (IP shock) and magnetic cloud. According to their model, the simultaneity of FD depends on the strength and propagation direction of interactive magnetic structures overtaking the Earth. Now the STEREO mission can visualize the emergence and propagation direction of the coronal mass ejection (CME) in 3-dimension in the heliosphere. Thus, it is possible to test the suggested mechanisms causing two different types of FD events. One simultaneous FD observed on February 17, 2011 may be caused by a CME heading directly toward the Earth observed on February 15, 2011 by the STEREO mission. The simultaneity of FD event is proved to be a useful analysis tool in figuring out the geo-effectiveness of solar events such as interplanetary CMEs and IP shocks.

• The Journal of Korea Robotics Society
• /
• v.13 no.2
• /
• pp.103-112
• /
• 2018

In this paper, a high performance underwater vehicle which can be manufactured at low cost is designed and fabricated, and its performance is verified through experiments. To improve efficiency, the Myring equation is used to design the appearance and the duct structure including the thruster is planned to increase the propulsion efficiency while reducing the drag force. Through various methods, it is secured stable waterproof performance, and also is devised to have high speed movement and turning performance. The developed underwater vehicle is equipped with a high output BLDC motor to achieve a linear speed of up to 2 m/s and can change direction rapidly with stability through four rudders. The rudders are driven by coupling a timing belt and a pulley by extending the axis of a servo motor, and are equipped at the end of the body to turn heading. In addition, for stable posture control, the roll keeps its internal center of gravity low and maintains its stability due to restoring force. By controlling the four rudders, pitch and yaw are handled by the PID controller and show stable performance. To investigate the horizontal turning performance, it is confirmed that the yaw rate controller is designed and stable yaw rate control is performed.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.6 no.1
• /
• pp.98-118
• /
• 2014

An auto weather-vaning system for a Dynamic Positioning (DP) vessel is proposed. When a DP vessel is operating, its position keeping is hindered by ocean environmental disturbances which include the ocean current, wave and wind. Generally, most ocean vessels have a longitudinal length that is larger than the transverse width. The largest load acts on the DP vessel by ocean disturbances, when the disturbances are incoming in the transverse direction. Weather-vaning is the concept of making the heading angle of the DP vessel head toward (or sway from) the disturbance direction. This enables the DP vessel to not only perform marine operations stably and safely, but also to maintain its position with minimum control forces (surge & sway components). To implement auto weather-vaning, a nonlinear controller and a disturbance observer are used. The disturbance observer transforms a real plant to the nominal model without disturbance to enhance the control performance. And the nonlinear controller deals with the kinematic nonlinearity. The auto weather-vaning system is completed by adding a weather-vaning algorithm to disturbance based controller. Numerical simulations of a semi-submersible type vessel were performed for the validation. The results show that the proposed method enables a DP vessel to maintain its position with minimum control force.

• Journal of Broadcast Engineering
• /
• v.2 no.2
• /
• pp.125-135
• /
• 1997

This paper is concerned with realistic mainpulation of content in video sequences. Manipulation of content in video sequences is one of the content-based functionalities for MPEG-4 Visual standard. We present an approach to synthesizing video sequences by using the intermediate outputs of three-dimensional (3D) motion and depth analysis. For concreteness, we focus on video showing 3D motion of an observer relative to a scene containing planar runways (or roads). We first present a simple runway (or road) model. Then, we describe a method of identifying the runway (or road) boundary in the image using the Point of Heading Direction (PHD) which is defined as the image of, the ray along which a camera moves. The 3D motion of the camera is obtained from one of the existing 3D analysis methods. Then, a video sequence containing a runway is manipulated by (i) coloring the scene part above a vanishing line, say blue, to show sky, (ii) filling in the occluded scene parts, and (iii) overlaying the identified runway edges and placing yellow disks in them, simulating lights. Experimental results for a real video sequence are presented.