• Proceedings of the Korean Nuclear Society Conference
• /
• 1995.10a
• /
• pp.429-436
• /
• 1995

This paper describes a methodology for determination of representative CANDU feeder geometry and the pressure drops between inlet/outlet header and fuel channel in the primary loop. A code, MEDOC, was developed based on this methodology and helps perform a calculation of equivalent feeder geometry for a selected channel group on the basis of feeder geometry data (fluid volume, mass flow rate, loss factor) and given property data pressure, quality, density) at inlet/outlet header. The equivalent feeder geometry calculated based on this methodology will be useful fur the transient thermohydraulic analysis of the primary heat transport system for the CANDU heavy water-cooled pressure tube reactor.

• Journal of Mechanical Science and Technology
• /
• v.20 no.7
• /
• pp.1030-1042
• /
• 2006

An experimental study has been performed to investigate the off-take phenomena at the header-feeder systems (horizontal header pipe with multiple feeder branch pipes) in a CANDU (CANadian Deuterium Uranium) reactor with the branch orientation varies ${\pm}36^{\circ}\;or\;{\pm}72^{\circ}$. In order to evaluate the applicability of the conventional correlations used in the safety analysis code, RELAP5-Mod3, the test facility is designed with the 1/2 scale of the. CANDU 6. It was found that the data set for the top, bottom and side branches are in a good agreement with the correlations used. However, for the specific angled branches, ${\pm}36^{\circ}\;and\;{\pm}72^{\circ}$, the onsets of off-take data and quality data showed large deviation with the conventional model inside RELAP5-MOD3. Furthermore, based on the uncertainty analysis, the conventional 2.5 power law needs to be modified. The present experimental data set can be useful for the construction of the general correlation considering the arbitrary branch orientation.

• Nuclear Engineering and Technology
• /
• v.36 no.2
• /
• pp.142-152
• /
• 2004

The liquid entrainment and vapor pull-through offtake model of RELAP5/MOD3 had been developed for SBLOCA (Small Break Loss of Coolant Accident). The RELAP5/MOD3 model for horizontal volumes accounts for the phase separation phenomena and computes the flux of mass and energy through a branch when stratified conditions occur in the horizontal pipe. In the case of CANDU reactor, this model should be used in the coolant flow of 95 feeders connected to the reactor header component under the horizontal stratification in header. The current RELAP5 model can treat the only 3 directions junctions; vertical upward, downward, and side oriented junctions, and thus improvements for the liquid entrainment and vapor pull-through model were needed for considering the exact angles. The RELAP5 off-take model was modified and generalized by considering the geometric effect of branching angles. Based on the previous experimental results, the critical height correlation was reconstructed by use of the branch line connection angle and validation analyses were also performed using SET. The new model can be applied to vertical upward, downward and angled branch, and the accuracy of the new correlations is more improved than that of RELAP5.

• Proceedings of the Korean Nuclear Society Conference
• /
• 2003.05a
• /
• pp.120-120
• /
• 2003

• Journal of the Korea Society for Simulation
• /
• v.15 no.4
• /
• pp.59-67
• /
• 2006

An efficient PCB assembly method with Gantry type machine is developed and proposed in this paper to improve system productivity. Nozzle changes at Gantry type machine is the major reason causing lower system performance instead of header and slot movements on the other type machines. The problem is attacked by maximizing multiple adsorptions to reduce the number of necessary nozzle changes with Gantry type machine. It is designed to reduce the assembly time per PCB with multiple adsorptions based upon the positions of feeders and nozzles. A simulation model is constructed to show the effectiveness of the suggested heuristic and necessarily a comparison study is followed with different methods on selection of next assembly feeder and nozzle with various cases.