• Journal of Mechanical Science and Technology
• /
• 제14권7호
• /
• pp.744-751
• /
• 2000

To achieve lower flying height for high areal recording density, the laser zone texturing of the disk needs to be designed to reduce glide height. One problem of the laser bump design is that the regular laser bump pattern often produces glide resonance phenomenon, which leads to failure of the glide height test. However, it was found in this study that glide resonance is an intrinsic problem of the glide head used and resonance phenomenon depends on the type of the head slider, that is, the natural frequency of the slider body. Therefore, higher glide height or glide failure caused by glide resonance does not lead to head/media interface problem in the real drive operating conditions in which the data head is used. Pseudo-random bump pattern greatly reduces the glide resonance. Smaller bump pitch will also help to reduce the glide resonance. However, as bump spacing becomes smaller, glide height will be increased due to increased air pressure developed around the bumps. Lowering bump height is the most effect way to reduce glide avalanche.

• KSTLE International Journal
• /
• 제5권1호
• /
• pp.28-31
• /
• 2004

The object of the present work is the natural frequency analysis of subambient pressure tri-pad and pico sliders. Head/disk interaction during start/stop and constant speed were detected by using the acoustic emission (AE) test system. The frequency spectrum analysis is performed using the AE signal obtained during the head/disk interaction. The FFT (Fast Fourier Transform) analysis of the AE signals is used to understand the interaction between the AE signal and the state of contact. Natural frequency analysis was performed using the Ansys program. The results indicate acceptable accordance of finite element calculation results with the experimental results.

• 제어로봇시스템학회논문지
• /
• 제10권2호
• /
• pp.153-163
• /
• 2004

The control objective in hard disk drives is to move head as fast as possible to target track and position the head over the center of target track in the presence of external disturbances. The external shock or disk clamping error in manufacturing process causes the disk center to deviate from the disk rotation center. The disk shift acts on the control system as disturbance and degrades severely the performance of disk drives. In this paper, we present a new controller that compensates for the periodic disturbances very fast. The disturbance compensator is arranged in parallel with the state feedback controller. To avoid the interference with the state feedback controller, the compensator creates compensation signal without the feedback of system output until steady state. The pulse type controller is included additionally for improving the transient performance due to initial state. Finally, in order to demonstrate the superior performance of the proposed compensator. we present some experimental results using a commercially available disk drive.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 추계학술대회논문집
• /
• pp.140-145
• /
• 2002

In high-capacity disk drives with ever-growing track density, the allowable level of position error signal (PES) is becoming smaller and smaller. A substantial portion of the PES is caused by disk vibration. This can be reduced by using a head gimbal assemblies (HGAs) that do not confine the slider movement to the vertical direction to disks, but allow movement to the radial direction of disks with respect to disk vibration. Several types of HGAs are proposed for such radial motion of the slider. Experimental results show that the PES levels are reduced by the proposed HGA-design concepts.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2004년도 춘계학술대회논문집
• /
• pp.189-194
• /
• 2004

As a disk drive becomes widely used in portable environments, one of the important requirements is durability under severe environmental condition, especially, resistance to mechanical shock. An important challenge in the disk recording is to improve disk drive robustness in shock environments. If the system comes In contact with outer shock disturbance, the system gets critical damage in head-gimbal assembly or disk. This paper describes analysis of a HGA(head-gimbal assembly) in micro MO drives to shock loading during both non-operating state and operating state. A finite element model which consists of the disk, suspension, slider and air bearing was used to find structural response of micro MO drives. In the operational case. the air bearing is approximated with four linear elastic springs. The commercially available finite element solver, ANSYS/LS-DYNA, is used to simulate the shock response of the HGA in micro MO drives. In this paper, the mechanical robustness of the suspension is simuiated considering the shock responses of the HGA.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 추계학술대회논문초록집
• /
• pp.320.2-320
• /
• 2002

In high-capacity disk drives with ever-growing track density, the allowable level of position error signal (PES) is becoming smaller and smaller. A substantial portion of the PES is caused by disk vibration. This can be reduced by using a head gimbal assemblies (HGAs) that do not confine the slider movement to the vertical direction to disks, but allow movement to the radial direction of disks with respect to disk vibration. Several types of HGAs are proposed for such radial motion of the slider. (omitted)

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 1998년도 춘계학술대회 및 발표대회 강연 및 발표논문 초록집
• /
• pp.6-6
• /
• 1998

In 1957, the first magnetic disk drive compatible with a movable head was introduced as an external file memory device for computer system. Since then, magnetic disks have been improved by increasing the recording density, which has brought about the development of a high performance thin film magnetic head. The thin film magnetic head has a magnetic circuit on a ceramic substrate using IC technology. The physical property of the substrate material is very important because it influences the tribology of head/disk interface and also manufacturing process of the head. $Al_{2}O_{3}$-TiC ceramics, so called ALTIC, is known to be one of the best substrate materials which satisfies this property requirement. Even though the head is not in direct contact with the disk, frequent instantaneous contacts are unavoidable due to its high rotating speed and the close gap between them. This may cause damage in the magnetic recording media and, thus, it is very important that the magnetic head has a good wear resistance. $Al_{2}O_{3}$-TiC ceramics has an excellent tribological property in head/disk interface. Manufacturing process of thin film head is similar to that of IC, which requires extremely smooth and flat surface of the substrate. The substrate must be readily sliced into the heads without chipping. $Al_{2}O_{3}$-TiC ceramics has excellent machineability and mechanical properties. $Al_{2}O_{3}$-TiC ceramics was first developed at Nippon Tungsten Co. as cutting tool materials in 1968, which was further developed to be used as the substrate materials for thin film head in collaboration with Sumitomo Special Metals Co., Ltd. in 1981. Today, we supply more than 60% of the substrates for thin film head market in the world. In this paper, we would like to present the sintering process of $Al_{2}O_{3}$-TiC ceramics and its property in detail.

• Tribology and Lubricants
• /
• 제17권1호
• /
• pp.40-55
• /
• 2001

Acoustic emission(AE) signal has been widely utilized to monitor the interaction at the head/disk interface. In this work the relationship between the AE signal and the state of contact between the slider and the disk is presented. Results of the FFT(Fast Fourier Transform) analyses of the AE signal could be used to better understand the interfacial interaction. Also, it was found that wear particles affect the AE signal. Therefore, the signal can be used to monitor the wear particle presence at the interface.

• 정보저장시스템학회:학술대회논문집
• /
• 정보저장시스템학회 2005년도 추계학술대회 논문집
• /
• pp.88-95
• /
• 2005

The head to disk spacing must be decreased to increase recording densities in hard disk drives. Recently, to decrease the head to disk spacing, smooth disk having no bumps onto the lading zone has used. In this research, we compared the number of particles generated in HDD with smooth and textured disks. We used a sampling method using a particle sampler and a CPC (condensation particle counter) to detect particles in HDD. First, we sampled and counted panicles generated with disk rotational speed and various rest times when the smooth disk and textured disks were used, then analyzed the sampled particles by SEM (scanning electron microscopy) and AES (auger electron spectroscopy). In results of measuring particles, more particles in case of LZT disk drive generated than that of the smooth disk drive in all test modes. The number of particles generated in the smooth disk was very low. The particle generation increased as the rest time increased (smooth/LZT disks) and more particles in case of LZT disk drive generated than that of the smooth disk drive. In results of analyzing particle components, Al, Ti, Si components were detected and we could not found differences between components in case of smooth/LZT disk drive.

• 정보저장시스템학회논문집
• /
• 제2권2호
• /
• pp.123-129
• /
• 2006

The head to disk spacing must be decreased to increase recording densities in hard disk drives. Recently, to decrease the head to disk spacing, smooth disk having no bumps onto the lading zone has used. In this research, we compared the number of particles generated ill HDD with smooth and textured disks. We used a sampling method using a particle sampler and a CPC (condensation particle counter) to detect particles in HDD. First, we sampled and counted particles generated with disk rotational speed and various rest times when the smooth disk and textured disks were used, then analyzed the sampled particles by SEM (scanning electron microscopy) and AES (auger electron spectroscopy). In results of measuring particles, more particles in case of LZT disk drive generated than that of the smooth disk drive in all test modes. The number of particles generated in the smooth disk was very low. The particle generation increased as the rest time increased (smooth/LZT disks) and more particles in case of LZT disk drive generated than that of the smooth disk drive. In results of analyzing particle components, Al, Ti, Si components were detected and we could not found differences between components in case of smooth/LZT disk drive.